MCombo Wooden Cat House
Owner's Manual
Model: 6012-CT090
Purchaser's Agreement
By accepting delivery of this product, you agree not to change, alter, or modify it, or remove or render unsafe any guards or safety features. You also agree not to refuse or neglect retrofit kits provided by MCombo to enhance safe use.
Contents
- Product Precautions
- Disclaimer
- Installation Preparation
- Assembly Instructions
- Warranty
- Return/Replacement Policy
- MCombo Customer Support
I. Product Precautions
- [Read Manual] Read and follow the information in the user's manual.
- [Keep away from children] Please keep kids away from small components to ensure safety.
- [Ventilate] Please ventilate before use.
- [Not chew-proof] Please note that the wood is not chew-proof.
- [Clean spills promptly] Please clean up water stains and pet excrement in time.
- [Do not overload] Do not place overweight items.
- [Handle with care] Please handle wood and other accessories properly.
II. Disclaimer
Ensure you read and understand this manual completely before using your MCombo Product. MCombo is not responsible for any damage or injury incurred due to improper or unsafe use, or any use that does not comply with applicable federal, state, or local laws or ordinances.
III. Installation Preparation
- Prepare a carpet or mat to protect your floor and spread out all accessories.
- Prepare a pair of gloves to avoid scratches from sharp wooden sawdust during installation.
- Open all boxes to check that accessories are complete and in good condition (refer to Part List).
- Keep small components away from children before installation.
- If using power tools, set the speed to low in advance to avoid damaging the wood.
IV. Assembly Instructions
1. Product Parameters
| Specification | Description |
|---|---|
| Product Model No. | 6012-CT090 |
| Package Quantity | 1 |
| Overall Dimension | 31.50 * 23.62 * 48.82 inch |
| Package Contains | Wood Panels, Accessory Packs, Instructions |
2. Part List
| Part | Description | Dimensions |
|---|---|---|
| A x1PC | Square Panel | 760*565mm |
| B x1PC | Square Panel | 760*565mm |
| C x1PC | Rectangular Panel with Door Frame | 800*600mm |
| D x1PC | Rectangular Panel | 800*600mm |
| E x1PC | Tall Slatted Panel | 1130*576mm |
| F x1PC | Tall Slatted Panel | 1130*576mm |
| G x1PC | Door Panel | 1124*398mm |
| H x1PC | Door Panel | 1124*398mm |
| I x1PC | Top Panel | 758*400mm |
| J x1PC | Shelf | 200*200mm |
| K x1PC | Shelf | 300*400mm |
| L x1PC | Cat-shaped Decorative Panel | 300*300mm |
| M x1PC | Wooden Support Bar | 300*20mm |
| N x1PC | Fence-like Divider | 330*100mm |
| O x1PC | Sloped Platform | 385*200mm |
3. Hardware
| Item | Description | Dimensions | Quantity |
|---|---|---|---|
| 1 | Screw | M3*12mm | 12+1PCS |
| 2 | Screw | M3*14mm | 12+1PCS |
| 3 | Screw | M3*16mm | 8+1PCS |
| 4 | Screw | M3.5*25mm | 22+2PCS |
| 5 | Screw | M3.5*35mm | 2PCS |
| 6 | Screw | M3.5*40mm | 8+1PCS |
| 7 | Screw | M6*30mm | 2PCS |
| 8 | Bolt with Nut | M6*35mm | 5+1PCS |
| 9 | Bolt with Nut | M6*45mm | 12+1PCS |
| 10 | Screw | M6*50mm | 7+1PCS |
| 11 | Dowel | Ø8*20mm | 9+1PCS |
| 12 | Bracket | - | 4PCS |
| 13 | Wheel/Caster | - | 2PCS |
| 14 | Hinge | - | 1PC |
| 15 | Hinge | - | 1PC |
| 16 | Wheel/Caster | - | 2PCS |
| 17 | Wheel/Caster | - | 2PCS |
| 18 | Wall Anchor Kit | - | 2PCS |
Assembly Steps
Step 1
Attach panel A to panel B using two screws (9). The diagram shows panels A and B standing upright. Panel A is on the left, panel B on the right. Two screws (9) are inserted from the outside of panel A into the edge of panel B. A close-up shows the screw head and nut assembly. Ensure the side with holes faces outwards.
Parts used: A x1, B x1, Screw (9) x2
Step 2
Attach panels E and F to the structure formed by A and B using eight screws (9). Panel E is attached to the left side, and panel F to the right side. The diagram shows the vertical slatted panels being attached to the edges of A and B. A close-up shows screw (9) being inserted through panel E/F into panel A/B.
Parts used: E x1, F x1, Screw (9) x8
Step 3
Insert eight dowels (11) into the designated holes on the top edges of the structure. The diagram shows the structure from a top-down perspective, with dowels (11) being inserted into the top corners and along the top edges.
Parts used: Dowel (11) x8
Step 4
Attach wooden support bar M to panel C using two screws (5) and one screw (11). Panel C is a rectangular panel with a door frame. The diagram shows bar M being attached horizontally to the inside of panel C, near the top. Screws (5) are inserted from the front of C into M, and screw (11) is inserted from the back of C into M.
Parts used: C x1, M x1, Screw (5) x2, Dowel (11) x1
Step 5
Attach panel C (with M attached) to the main structure using four screws (6) and two screws (10). The diagram shows panel C being attached to the front of the structure, between panels A and F. Screws (6) are inserted from the outside of A and F into the edges of C. Screws (10) are inserted from the inside of the structure into the edge of C.
Parts used: C x1, Screw (6) x4, Screw (10) x2
Step 6
Attach panel D to the main structure using four screws (6) and two screws (10). Panel D is similar to C but without the door frame. The diagram shows panel D being attached to the front of the structure, between panels A and E. Screws (6) are inserted from the outside of A and E into the edges of D. Screws (10) are inserted from the inside of the structure into the edge of D.
Parts used: D x1, Screw (6) x4, Screw (10) x2
Step 7
Attach four wheel/casters (16) to the bottom corners of the structure using sixteen screws (4). The diagram shows the bottom of the structure. Two wheels (16) are attached to the front corners, and two wheels (17) are attached to the rear corners. Screws (4) are used for attachment. A note indicates parts #16 need to be installed on the front side.
Parts used: Wheel/Caster (16) x2, Wheel/Caster (17) x2, Screw (4) x16
Step 8
Install shelf I using four bolts with nuts (8). The diagram shows shelf I being placed horizontally inside the structure. Bolts (8) are inserted through the side panels (E/F) and into the edges of shelf I. A close-up shows the bolt and nut assembly. A note indicates to pay attention to the side with holes underneath the panel, put it in front.
Parts used: I x1, Bolt with Nut (8) x4
Step 9
Attach the fence-like divider N using two screws (4). The diagram shows divider N being installed vertically in the lower section of the cat house, between panels E and F. Screws (4) are inserted from the outside of the side panels into the divider.
Parts used: N x1, Screw (4) x2
Step 10
Install shelf J using two screws (9) and one screw (10). The diagram shows shelf J being placed horizontally above divider N. Screws (9) are inserted from the outside of the side panels into the edge of shelf J. Screw (10) is inserted from the back panel into the edge of shelf J. A note indicates part #10 needs to be installed from the back panel.
Parts used: J x1, Screw (9) x2, Screw (10) x1
Step 11
Install shelf K using one bolt with nut (8) and two screws (10). The diagram shows shelf K being placed horizontally in the upper section. Bolt (8) is inserted through the side panel into the edge of shelf K. Screws (10) are inserted from the back panel into the edge of shelf K.
Parts used: K x1, Bolt with Nut (8) x1, Screw (10) x2
Step 12
Attach the cat-shaped decorative panel L using four screws (4). The diagram shows panel L being mounted on the upper shelf (K). Screws (4) are inserted through panel L into the shelf.
Parts used: L x1, Screw (4) x4
Step 13
Attach the sloped platform O using four screws (1). The diagram shows platform O being mounted in the upper section, angled downwards. Screws (1) are inserted through the platform into the side panels.
Parts used: O x1, Screw (1) x4
Step 14
Attach door G and door H using twelve screws (2). The diagram shows doors G and H being attached to the front frame (C). Hinges are pre-attached to the doors. Screws (2) are used to secure the hinges to the frame. A close-up shows the hinge attachment with screws (2).
Parts used: G x1, H x1, Screw (2) x12
Step 15
Attach door hardware using screws (3), screws (7), and screws (12). The diagram shows the attachment of latches and handles to the doors and frame. Four brackets (12) are attached to the frame using screws (3). Two screws (7) are used for handles on the doors. Four screws (12) are used for the latches. The diagram shows close-ups of these attachments.
Parts used: Screw (3) x8, Screw (7) x2, Bracket (12) x4, Screw (12) x4, Screw (13) x2
Step 16
Attach hinges (14 and 15) to the doors using screws (1). The diagram shows the attachment of hinges to the doors G and H. Four screws (1) are used for each hinge. The diagram shows close-ups of hinge attachment.
Parts used: Hinge (14) x1, Hinge (15) x1, Screw (1) x8
Step 17
Secure the cat house to the wall using two wall anchor kits (18). The diagram shows the top rear of the cat house being attached to a wall. The wall anchor kits (18) are used to fasten the structure to the wall for stability. A close-up shows the wall anchor and screw. A note indicates parts marked with a checkmark (✓) are required for this step.
Parts used: Wall Anchor Kit (18) x2
Step 18
Secure the cat house to the wall using two wall anchor kits (18). This step appears to be a repeat or a different angle of wall anchoring. The diagram shows the side rear of the cat house being attached to a wall. Wall anchor kits (18) are used. A note indicates parts marked with a checkmark (✓) are required for this step.
Parts used: Wall Anchor Kit (18) x2
Step 19
Secure the cat house to the wall using two wall anchor kits (18). The diagram shows the top rear of the cat house being attached to a wall using straps and wall anchors. The straps are looped through attachment points on the cat house and secured to the wall. A note indicates parts marked with a checkmark (✓) are required for this step.
Parts used: Wall Anchor Kit (18) x2
Step 20
Final check. The cat house is fully assembled. The diagram shows the completed wooden cat house with doors closed.
FINISH
V. Warranty
Notice
- For products beyond the limited manufacturer warranty period and scope, MCombo can provide replacement service for a basic charge.
- The warranty applies only to MCombo products and does not include accessories or enhancements.
- Warranties are valid in the 48 contiguous United States and contingent upon operating the product according to the manual.
| Category | Warranty Period |
|---|---|
| Wood | ★ 1 Year |
| Hardware | ★ 6 months |
CONSUMER WARRANTY LIMITATIONS AND EXCLUSIONS
All warranties begin on the date of delivery and are to the original purchaser from MCOMBO® ONLY.
- MCOMBO® will replace defective parts or send replacement product if parts have not been subjected to misuse, abuse, or improper service.
- Exclusions include damage caused by: Contamination, Abuse, misuse, accident, or negligence, Commercial use, or use other than normal, Improper operation, maintenance, or storage.
NOTE: MCOMBO® will pay standard shipping rates on all warranted parts for the first year. Replacement parts out of warranty can be purchased at a discount price.
VI. Return/Replacement Policy
Notice
Why don't we recommend returning the item by yourself?
- Huge cost - UPS/FedEx oversize fee.
- Need you to take the box to UPS/FedEx facility.
Return/ Replacement Policy
MCOMBO® offers a straightforward, hassle-free return policy. You have 30 days from the date of purchase to return any item purchased from our store. We accept returns of items in new or used condition, with all original packaging and components included. Refunds will be issued in the original form of payment.
NOTE:
- Please keep the original packaging. If unavailable, new packaging must meet UPS/FedEx size standard: (width + height) * 2 + length < 128 inches.
- Disassemble the product before returning to avoid huge costs for oversized items.
- Do not purchase return labels for damaged/defective products yourself.
- If you have any problem returning the product, please contact MCOMBO® customer support.
VII. MCOMBO Customer Support
If you have any questions or suggestions, please refer to the following contact information. MCOMBO® will do its best to work with you to ensure you are entirely satisfied.
- Email: sales@mcombo.com (Respond within 24 hours)
- Phone: 1-323-597-1109 (8:00 a.m. - 4:00 p.m. PST, Monday-Friday)
Locations:
-
DE
2411 Bear Corbitt Rd STE 1
New Castle, DE, 19720
1-302-268-8644 -
CA
2808 Vail Ave
Commerce, CA, 90040
1-323-597-1109 -
TN
3980 PREMIER AVE,
MEMPHIS, TN, 38118
