Renogy ONE Core Quick Guide

Before Getting Started

This quick guide provides important operation and maintenance instructions for the Renogy ONE Core (referred to as Core). Please read it carefully before operation and save it for future reference. Failure to observe the instructions or precautions may result in electrical shock, serious injury, or death, or damage to the Renogy ONE Core.

Renogy ensures the accuracy and applicability of information at the time of printing, but product improvements may occur. Renogy assumes no responsibility for losses caused by failure to install or use the product in compliance with this guide. Renogy is not liable for failures, damages, or injuries resulting from repairs attempted by unqualified personnel or improper installation and operation.

Illustrations are for demonstration purposes only and may vary slightly depending on product revision and market region. Renogy reserves the right to change information without notice. For the latest quick guide, visit renogy.com.

Online Manuals:

• Quick Guide
• User Manual

What's In the Box?

• Renogy ONE Core × 1
• Mounting Screws (M3.5*14mm) × 4 (1 extra)
• Power Cable (5m) × 1
• Quick Guide × 1

Get to Know RENOGY ONE Core

Components:

• Mounting Holes
• On/Off Button
• Communication Port
• Bubble Level
• Power Port
• Type-C Port

Installation Site and Environment

Recommended Installation:

• Ensure the screen points to the front, rear, left, or right side of the RV, vertically to the RV floor for the leveling function.
• Use RV leveling blocks during the leveling process.

Environmental Conditions:

• Altitude: ≤5000m
• Temperature: -4°F to 158°F (-20°C to 70°C)
• Humidity: 0% to 95%

Handling Precautions:

• Keep Dry ?
• Fragile ⚠️
• Indoor Use ?

Required Tools

• Phillips Screwdriver (#1)
• Insulation Tape
• Skill Saw (optional, for flush mounting)
• Impact Drill with Hole Saw, 2.17in/55mm (optional, for flush mounting)

NOTE: Tools are required only when the Core is flush mounted on a wall.

Installation Steps

Step 1 (A): Place Renogy ONE Core on a Table

The package box can be used as a bracket for installation if wall mounting is not required.

NOTE: The RV leveling function is unavailable when the Core is placed on a table.

Step 1 (B): Mount Renogy ONE Core on a Wall

Use the provided mounting template (or a paper copy) for drilling holes. The installation hole size is 2.17 in x 2.17 in (55 mm x 55 mm).

Follow the numbered steps for mounting:

1. Use the mounting template to mark drilling locations.
2. Drill holes at the marked locations.
3. Insert wall anchors if necessary.
4. Secure the mounting bracket to the wall using mounting screws.
5. Attach the Renogy ONE Core to the bracket.

Step 2: Connect Renogy ONE Core to a Power Supply

You can connect the Core to a power supply using the included power cable or an optional Type-C cable.

• Installed on a Wall: Connect the DC Power (8-60V) using the included Power Cable. Alternatively, use a Type-C Cable (5V, DC) (optional).
• Installed on a Table: Connect the DC Power (8-60V) using the included Power Cable. Alternatively, use a Type-C Cable (5V, DC) (optional).

NOTE: When installing the power cable, connect the negative terminal first, then the positive terminal.

Step 3: Install a Communication Cable (Optional)

For details, see the Renogy ONE Core User Manual by scanning the QR code in the guide. Connect using an RJ45 Ethernet Cable (Max length: 6 m) to Devices (RS-485).

Step 4: Power On/Off

Long press the On/Off Button for 5 seconds to power the Core on or off.

Step 5: Pairing with DC Home

For initial startup, follow the startup wizard on the Core to pair it with the DC Home app. Alternatively, navigate to System > Pair with App.

Scan the QR code to pair Renogy ONE Core with the DC Home app.

Step 6: Add Devices

Renogy ONE Core can connect to Bluetooth, Bluetooth mesh, and Zigbee Renogy devices concurrently.

RV Leveling

Follow the on-screen prompts by navigating to > RV Leveling. Calibrate the RV leveling function each time the installation site is changed.

Important Safety Instructions

• Keep Renogy ONE Core out of the reach of children.
• Dispose of the product according to local, state, and federal regulations.
• Do not expose the Core to flammable or harsh chemicals or vapors.
• Do not open, dismantle, repair, or modify the Core. There are no serviceable parts inside.
• Confirm the polarities of devices before connecting to a power supply to avoid damage and voiding the warranty.
• Ensure the connected DC power supply is rated at 8V to 60V. Connecting to a power source outside this range may cause failure or permanent damage.
• An extended power cable can be used on demand. Refer to the Renogy ONE Core User Manual for details.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, try to correct the interference by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consulting the dealer or an experienced radio/TV technician.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

RSS Standard

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The device is compliance with RF exposure guidelines; users can obtain Canadian information on RF exposure and compliance. The minimum distance from body to use the device is 20cm.

French: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio électrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Le présent appareil est conforme après examen de ce matériel aux conformité ou aux limites d'intensité de champ RF, les utilisateurs peuvent sur l'exposition aux radiofréquences et compliance d'acquérir les informations correspondantes. La distance minimale du corps à utiliser le dispositif est de 20cm.

Renogy Support

To discuss inaccuracies or omissions in this quick guide or user manual, visit or contact Renogy at:

• renogy.com/support/downloads
• contentservice@renogy.com

For technical questions about your product in the U.S., contact the Renogy technical support team through:

• renogy.com/contact-us
• Phone: 1(909)2877111

For technical support outside the U.S., visit the local Renogy website:

• Canada: ca.renogy.com
• United Kingdom: uk.renogy.com
• Australia: au.renogy.com
• South Korea: kr.renogy.com
• China: www.renogy.cn
• Japan: renogy.jp
• Germany: de.renogy.com
• Other Europe: eu.renogy.com

Disclaimer

Renogy ONE Core Quick Guide © 2023 Renogy. All rights reserved. RENOGY and RENOGY are registered trademarks of Renogy.

All information in this quick guide is subject to copyright and other intellectual property rights of Renogy and its licensors. The quick guide may not be modified, reproduced, or copied, in whole or in part, without the prior written permissions of Renogy and its licensors.

The registered trademarks in this quick guide are the property of Renogy. Unauthorized use of the trademarks is strictly prohibited.