Vera Dream Storage Bed Assembly Instructions
Vendor Information
Vendor Name: LSMX1
Vendor Code: V-005852
Vendor Collection: VERA DREAM STORAGE
Parts List
| ITEM | DESCRIPTION | QUANTITY |
|---|---|---|
| 1 | VERA DREAM HEADBOARD | 1 PIECE |
| 2 | VERA DREAM RAILS/SLATS | 1 KIT |
| 3 | VERA DREAM FOOTBOARD | 1 PIECE |
| 4 | VERA DREAM DRAWERS | 1 KIT |
Hardware Included
- A 5/16-18X1" SCREW BUTTON HEAD CAP (x8)
- B WASHER 5/16 PLAIN (x8)
- C 3/16 SHORT ARM HEX KEY (x2)
- D 5/16-18X 1 1/2" SCREW BUTTON HEAD CAP (x2)
Hardware bag included in side rails and slat box with red ribbon to located.
Assembly Steps
STEP 1: Attach side rails to headboard
Attach the side rails (2) to the headboard (1) using Wrench (C), 4 Screws (A) and Washers (B).
Diagram shows side rails connecting to the headboard with screws and washers.
STEP 2: Attach the "L" shape Slat to side rails
Attach the "L" shape slat (3) to the side rails (2) using 2 Screws (A) and Washer (B).
Diagram shows an L-shaped slat being attached to the side rails.
STEP 3: Attach support legs to center slat
Attach the support legs with leveler to the center slat. Adjust the levers on bottom of support legs when necessary.
Diagram shows support legs being attached to a center slat, with an instruction to turn right.
STEP 4: Place the piece into the U-shaped slot
Place the piece from top to bottom into the U-shaped slot.
Diagram shows a panel being placed into a U-shaped slot.
STEP 5: Secure the center slat
Hold the center slat with the "L" shape slat using Wrench (C), 1 Screw (D) and Washer (B).
Diagram shows the center slat being secured with a screw, washer, and wrench.
STEP 6: Insert the footboard storage assembly
Insert the footboard storage assembly (instructions on drawers box) into bed assembly as shown in the picture.
Diagram shows the footboard storage assembly being inserted into the main bed frame.
STEP 7: Unroll the slats
Unroll the slats onto the center slat starting at the footboard and ending at the headboard.
Diagram shows slats being unrolled across the bed frame.
STEP 8: Verify slat installation
Verify the slats are installed properly; the legs are perpendicular to the floor for full support.
Diagram shows a side view of the bed with slats properly installed, indicating perpendicularity to the floor.
Vera Dream Wings Assembly Instructions
(Note: These instructions are for attaching optional Vera Dream Wings)
STEP 1: Loosen screw
Loosen the screw (C), using a wrench (E) and turn it counterclockwise.
STEP 2: Turn plate
Turn a plate clockwise and one for the counterclockwise.
STEP 3: Tighten screw
To tighten the screw (C) turn the wrench (E), following the direction of the hands of a clock.
STEP 4: Attach brackets
Attach brackets (A & B) in the holes on the back and under the wings, using wrench (E), screw (C), and flat washers (D), following the direction of the clock.
Diagram shows the attachment of slot brackets and corner brackets to the wings using screws and washers.
STEP 5: Raise bed to put inside side rail of wing bracket
Raise bed to put inside the side rail of wing bracket.
Diagram shows the bed being raised to align with the wing bracket's side rail.
STEP 6: Attach bracket to headboard
Attach bracket (A) to headboard, using wrench (E), 4 screws (C), and flat washers (D), following the direction of the hands of a clock.
Diagram shows a bracket being attached to the headboard with screws, washers, and a wrench.
