ASSEMBLY GUIDE

Fixed Frame
Projector Screen
NS-SCR120FIX19W / NS-SCR100FIX19WINSIGNIA NS SCR120FI 19W Fixed Frame Projector ScreenBefore using your new product, please read these instructions to prevent any damage.
Contents

IMPORTANT SAFETY INSTRUCTIONS

  • Don’t install the product on a plasterboard surface. You can mount it on a  brick surface, concrete surface, and wooden surface (wooden thickness is more than 0.5 in. [12 mm]).
  • Be careful of the burrs and sharp cuts in the aluminum frames when installing.
  •  Use two people to assemble this product.
  •  After assembly, you’ll need two people to carry your frame.
  •  Make sure that you install the projection screen in a horizontal position.
  • We suggest that you use the product indoors. Using your screen outdoors for
    an extended time can make the screen surface turn yellow.
  • WARNING: Take care when installing this product. Installation faults, incorrect operation, and any natural calamities that cause damage to your screen or injuries to persons is not covered by the Warranty.
  •  Do not touch the screen surface with your hand.
  •  Do not clean the screen surface with corrosive detergent.
  • Do not scratch the screen surface with a hand or sharp object.

Features

  •  A simple solution for your home theater needs
  •  The high-quality matte white screen supports resolutions as high as 4K Ultra HD
  • Rigid and durable aluminum frame keeps the screen flat and taunt
  • Black velvet frame gives the screen an elegant, theatrical look with a 152° viewing angle Dimensions

INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - screen flat 1

Tools needed

You need the following tools to assemble your projector screen:

Phillips screwdriver INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 1
Pencil INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 2
Hammer or mallet INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 5
Drill with 8 mm bit INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 9

Package contents

Make sure that you have all the parts and hardware needed to assemble your new projector screen.
Parts

INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts Right horizontal frame piece (2)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 1 Left horizontal frame piece (2)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 3 Vertical frame piece (2)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 4 Support rod (1)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 5 Screen fabric (1 roll)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 7 Short fiberglass tube (4)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 6 Long fiberglass tube (2)

Hardware

HARDWARE #
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 8 Corner bracket 4
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 9Screw (24 + 2 spares) 26
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 9Hanging bracket A 2
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 11Hanging bracket B 2
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 12Spring (100 in. model: 38 + 4 spares)
(120 in. model 48 + 4 spares)
83/48
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 17Joint bracket 2
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 16Installation hook 2
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 15Bakelite screw 6
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 14Plastic anchor 6
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 13Fiberglass tube joint 2

Assembly instructions
Step 1 – Assemble the frame
You’ll need

INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 1 Left horizontal frame piece (2)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts Right horizontal frame piece (2)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 3 Vertical frame piece (2)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 1 Phillips screwdriver
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 17 Joint bracket (2)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 9 Screw (24)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 8 Corner bracket (4)

1 Connect a left horizontal frame piece to a right horizontal tube with a joint bracket and four screws to create a long horizontal tube. Repeat to connect the other left and right horizontal frame pieces.INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - the frame 8

2 Place the four frame pieces on the ground to form a rectangle.INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - the frame 7

3 Slide a corner bracket into a horizontal frame piece and into a vertical frame piece. Repeat for the other three frame sides.

Adjust the four frame pieces to create a rectangle. The outer corners of the frame should be 90° angles.INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - the frame 6

Lock the frame pieces into place using four screws for each corner.INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - frame pieces

Note: If there’s a big gap between the frame pieces, adjust the tightness of the screws to reduce the gap.
Step 2 – Assemble the screen You’ll need

INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - the frame 5Connect two of the short fiberglass tubes with a fiberglass joint to create one extra-long fiberglass tube. Repeat to connect the other two short fiberglass tubes. INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - the frame 4

2 Insert the long fiberglass tubes vertically and the extra-long fiberglass tubes horizontally into the tube slots on the screen fabric.INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - the frame 3

3 Make sure that the white side of the fabric is facing down, then place the screen flat into the frame.INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - screen flat

Step 3 – Attach the screen to the frame You’ll need

INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 12 Spring (100 in. models: 38) (120 in. model 48)
Note: Each model comes with 4 spare springs
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 7 Support rod (1)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 16 Spring hook (1)

On the back of the frame, insert the small hook on hook into the grove near the outer edge of the frame. Repeat this step to install 37 (100 in. model) or 47 (120 in. model) springs. INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - the frame 2

Use the installation hook to pull the large hook toward the center of the frame, then insert the large hook into the hole in the screen fabric. Repeat with all the remaining springs.INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - the frame 1

Locate the springs in the middle of the top and bottom of the frame, then insert the top of the support rod into the notch groove on the spring. Repeat to install the bottom of the rod. The rod should snap into place.INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - the frame

Step 4 – Hang your projector screen You’ll need

INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 17 Hanging bracket A (2)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 11 Hanging bracket B (2)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 5 Pencil
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 1 Phillips screwdriver
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 9 Drill with 8 mm bit
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 15 Bakelite screws (6)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 14 Plastic anchors (6)
INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Parts 2 Hammer or mallet
  1.  Align one of the hanging brackets A on the wall where you want to install the top of your projector screen. Make sure that the top of the bracket is level on the wall.
    The distance between the hanging brackets A should be 100 in. the model: More than 4.8 (1.45 m) and less than 5.9 ft. (1.8 m). 120 in. model: More than 5.7 ft. (1.75 m) and less than 6.6 ft. (2 m).INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Moving your screen 3
  2. Drill pilot holes through the screw holes on the bracket and into the wall with a drill with an 8 mm bit.INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - drill 1
  3. Insert a plastic anchor into each screw hole you drilled. Make sure that the anchor is flush with the wall. If needed, tap the anchors with a hammer or mallet.
  4.  Secure the bracket to the wall with two of the Bakelite screws.
  5. Install the other hanging bracket A. Make sure that the tops of both brackets are level with each other.
  6. Hang the top of your projector screen on the A brackets.
  7.  Hang the hanging brackets B on the bottom of the aluminum frame, then slide the brackets so they align with the A brackets. The distance between brackets B should be the same as the distance you used for brackets A.
    Note: Make sure that you attach brackets B to the aluminum frame first, then secure the brackets to the wall.
  8. Mark the screw holes in brackets B, then drill pilot holes through the screw holes on the brackets and into the wall with a drill with an 8 mm bit.
  9. INSIGNIA NS SCR120FI 19WInsert a plastic anchor into each screw hole you drilled. Make sure that the anchor is flush with the wall. If needed, tap the anchors with a mallet or hammer.
    Secure the brackets B to the wall with one screw per bracket.INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Moving your screen 1

Maintaining your screen

  •  Use a soft brush or wet cloth to clean the screen surface.
  •  Don’t clean the screen surface with corrosive detergents. Wipe the screen surface with a non-corrosive detergent.

Moving your screen

  • Have two people move your projector screen, one on each side.
  •  Make sure that the screen stays level during moving.
  •  Don’t twist the frame.

INSIGNIA NS SCR120FI 19W Fixed Frame Projector Screen - Moving your screen

Storing your screen

  1. Remove the screen from brackets B.
  2. If you want to roll the fabric, remove the springs. Roll the fabric into a tube to prevent damage.
  3.  Do not disassemble the frame. You can damage the frame pieces.
    Note: To protect the screen, cover it with a piece of cloth or plastic.

Specifications

Dimensions (H × W × D) 100 in. model:
54 × 92 × 1.4 in. (137 × 234 × 3.6 cm)
120 in. model:
64 × 110 × 1.4 in. (163 × 280 × 3.6 cm)
Weight 100 in. model: 17.4 lbs (7.9 kg)
120 in. model: 21.1 lbs: (9.6 kg)
Screen gain 1.05
Viewing angle 152°
Screen material PVC

ONE-YEAR LIMITED WARRANTY

Definitions:
The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”). For this warranty to apply, your Product must be purchased in the United States or Canada from a Best Buy branded retail store or online at www.bestbuy.com or www.bestbuy.ca and is packaged with this warranty statement.
How long does the coverage last?
The Warranty Period lasts for 1 year (365 days) from the date you purchased the Product. Your purchase date is printed on the receipt you received with the Product.
What does this warranty cover?
During the Warranty Period, if the original manufacture of the material or workmanship of the Product is determined to be defective by an authorized Insignia repair center or store personnel, Insignia will (at its sole option): (1) repair the Product with new or rebuilt parts; or (2) replace the Product at no charge with new or rebuilt comparable products or parts. Products and parts replaced under this warranty become the property of Insignia and are not returned to you. If service of Products or parts are required after the Warranty Period expires, you must pay all labor and parts charges. This warranty lasts as long as you own your Insignia Product during the Warranty Period. Warranty coverage terminates if you sell or otherwise transfer the Product.
How to obtain warranty service?
If you purchased the Product at a Best Buy retail store location or from a Best Buy online website (www.bestbuy.com or www.bestbuy.ca), please take your original receipt and the Product to any Best Buy store. Make sure that you place the Product in its original packaging or packaging that provides the same amount of protection as the original packaging. To obtain warranty service, in the United States and Canada call 1-877-467-4289. Call agents may diagnose and correct the issue over the phone.
Where is the warranty valid?
This warranty is valid only in the United States and Canada at Best Buy branded retail stores or websites to the original purchaser of the product in the country where the original purchase was made.
What does the warranty not cover?
This warranty does not cover:

  • Customer instruction/education
  • Installation
  • Set up adjustments
  •  Cosmetic damage
  •  Damage due to weather, lightning, and other acts of God, such as power surges
  •  Accidental damage
  • Misuse
  • buse
  • Negligence
  •  Commercial purposes/use, including but not limited to use in a place of business or in communal areas of a multiple dwelling condominium or apartment complex, or otherwise used in a place of other than a private home.
  • Modification of any part of the Product, including the antenna
  • Display panel damaged by static (non-moving) images applied for lengthy periods (burn-in).
  •  Damage due to incorrect operation or maintenance
  • Connection to an incorrect voltage or power supply
  • Attempted repair by any person not authorized by Insignia to service the Product
  • Products sold “as is” or “with all faults”
  •  Consumables, including but not limited to batteries (i.e. AA, AAA, C, etc.)
  •  Products where the factory-applied serial number has been altered or removed
  •  Loss or Theft of this product or any part of the product
  • Display panels containing up to three (3) pixel failures (dots that are dark or incorrectly illuminated) grouped in an area smaller than one-tenth (1/10) of the display size or up to five (5) pixel failures throughout the display. (Pixel-based displays may contain a limited number of pixels that may not function normally.)
  • Failures or damage caused by any contact including but not limited to liquids, gels, or pastes.

REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY FOR BREACH OF WARRANTY. INSIGNIA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS  PRODUCT, INCLUDING, BUT NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST PROFITS. INSIGNIA  PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A  PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.
Contact Insignia:
1-877-467-4289
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its affiliated companies.
*Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.

www.insigniaproducts.com
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
INSIGNIA is a trademark of Best Buy and its affiliated companies.
Distributed by Best Buy Purchasing, LLC
©2020 Best Buy. All rights reserved.
V1 ENGLISH
20-0294

Documents / Resources

INSIGNIA NS-SCR120FIX19W Fixed Frame Projector Screen [pdf] Installation Guide
NS-SCR120FIX19W, NS-SCR100FIX19W, NS-SCR120FIX19W Fixed Frame Projector Screen, Fixed Frame Projector Screen

Leave a comment

Your email address will not be published.