Beijer ELECTRONICS GT-4564 Analog Fitar
Ƙayyadaddun bayanai
- Samfura: GT-4564 Analog Fitar Module
- Tashoshi: 4
- Fitarwa Voltage: +/- 10 V
- Ƙaddamarwa: 16 bit
- Nau'in Tasha: Kaji Clamp, 10 pt m tasha
Umarnin Amfani da samfur
Shigarwa
- Tabbatar cewa an kashe wutar lantarki kafin shigar da Module na Analog Output.
- Haɗa ƙirar zuwa ramin da aka keɓance a cikin tsarin G-jerin bibiyar zanen wayoyi da aka bayar.
- Danne kejin clamps amintacce don tabbatar da haɗin kai mai kyau.
Saita
- Ƙarfi akan tsarin G-jerin bayan shigarwa.
- Samun dama ga tsarin dubawar tsarin kuma nemo saitin saituna don Module Fitowar Analog.
- Sanya abin da ake so voltage kewayon da ƙuduri bisa ga bukatun aikace-aikacenku.
Amfani
- Da zarar saitin ya cika, Module Fitar Analog yana shirye don canza siginar dijital zuwa vol na analogtage fitarwa.
- Aika sigina na sarrafawa daga software na aikace-aikacen ku zuwa ƙirar don samar da siginar fitarwa na analog tsakanin kewayon kewayon.
Game da Wannan Jagoran
Wannan littafin ya ƙunshi bayani kan software da kayan aikin masarufi na Beijer Electronics GT-4564 Analog Output Module. Yana ba da cikakkun bayanai masu zurfi, jagora akan shigarwa, saiti, da amfani da samfurin.
Alamomin da Aka Yi Amfani da su a cikin Wannan Jagoran
Wannan ɗaba'ar ya haɗa da Gargaɗi, Tsanaki, Bayanan kula da gumaka masu mahimmanci inda ya dace, don nuna masu alaƙa da aminci, ko wasu mahimman bayanai. Ya kamata a fassara alamomin da suka dace kamar haka:
GARGADI
Alamar faɗakarwa tana nuna yanayi mai yuwuwar haɗari wanda, idan ba a kiyaye shi ba, zai iya haifar da mutuwa ko mummuna rauni, da babban lahani ga samfurin.
HANKALI
Alamar taka tsantsan tana nuna yanayi mai yuwuwar haɗari wanda, idan ba a kiyaye shi ba, zai iya haifar da ƙaramin rauni ko matsakaici, da matsakaicin lalacewa ga samfurin.
NOTE
Alamar bayanin kula tana faɗakar da mai karatu zuwa ga gaskiya da yanayi masu dacewa.
MUHIMMANCI
Muhimman alamar yana nuna mahimman bayanai.
Tsaro
Kafin amfani da wannan samfurin, da fatan za a karanta wannan jagorar da sauran littattafan da suka dace a hankali. Biya cikakken hankali ga umarnin aminci!
Babu wani abu da Beijer Electronics zai kasance da alhakin ko alhakin lalacewa sakamakon amfani da wannan samfurin.
Hotunan, examples da zane-zane a cikin wannan jagorar an haɗa su don dalilai na misali. Saboda yawancin masu canji da buƙatun da ke da alaƙa da kowane takamaiman shigarwa, Beijer Electronics ba zai iya ɗaukar nauyi ko alhaki don ainihin amfani dangane da tsohonamples da zane-zane.
Takaddun shaida na samfur
Samfurin yana da takaddun takaddun samfur masu zuwa.
Janar Bukatun Tsaro
GARGADI
- Kada a haɗa samfuran da wayoyi tare da wutar da aka haɗa da tsarin. Yin haka yana haifar da “bakin filashi”, wanda zai iya haifar da al’amura masu haɗari da ba zato ba tsammani (ƙonawa, wuta, abubuwa masu tashi, matsa lamba, fashewar sauti, zafi).
- Kar a taɓa tubalan tasha ko na'urorin IO lokacin da tsarin ke gudana. Yin hakan na iya haifar da girgiza wutar lantarki, gajeriyar kewayawa ko rashin aiki na na'urar.
- Kada ka bari abubuwan ƙarfe na waje su taɓa samfurin lokacin da tsarin ke gudana. Yin hakan na iya haifar da girgiza wutar lantarki, gajeriyar kewayawa ko rashin aiki na na'urar.
- Kada ka sanya samfurin kusa da abu mai ƙonewa. Yin hakan na iya haifar da gobara.
- Duk aikin wayoyi ya kamata injiniyan lantarki ya yi.
- Lokacin sarrafa kayan aikin, tabbatar da cewa duk mutane, wurin aiki da marufi suna da tushe sosai. Guji taɓa abubuwan da ke gudana, samfuran sun ƙunshi abubuwan lantarki waɗanda za a iya lalata su ta hanyar fitarwar lantarki.
HANKALI
- Kada a taɓa amfani da samfurin a cikin mahallin da zafin jiki sama da 60 ℃. Guji sanya samfurin a cikin hasken rana kai tsaye.
- Kada a taɓa amfani da samfurin a cikin mahallin sama da 90% zafi.
- Yi amfani da samfur koyaushe a cikin mahalli tare da gurɓataccen digiri 1 ko 2.
- Yi amfani da madaidaicin igiyoyi don yin wayoyi.
Game da Tsarin G-jerin
Tsarin ya ƙareview
- Module Adaftar hanyar sadarwa: Tsarin adaftar hanyar sadarwa yana samar da hanyar haɗin kai tsakanin bas ɗin filin da na'urorin filin tare da ƙirar faɗaɗa. Haɗin zuwa tsarin bas na filin daban-daban na iya kafa ta kowane ɗayan adaftar cibiyar sadarwa mai dacewa, misali, don MODBUS TCP, Ethernet IP, EtherCAT, PROFINET, CC-Link IE Field, PROFIBUS, CANopen, DeviceNet, CC-Link, MODBUS/Serial da sauransu.
- Module Fadada: Nau'in nau'ikan haɓakawa: Digital IO, Analog IO, da kayayyaki na musamman.
- Saƙo: Tsarin yana amfani da saƙo iri biyu: Saƙon sabis da saƙon IO.
IO Tsarin Taswirar Bayanai
Tsarin fadada yana da nau'ikan bayanai guda uku: bayanan IO, ma'aunin daidaitawa, da rajistar ƙwaƙwalwar ajiya. Ana yin musayar bayanai tsakanin adaftar cibiyar sadarwa da tsarin haɓakawa ta hanyar aiwatar da bayanan hoto na IO ta hanyar yarjejeniya ta ciki.
Gudun bayanai tsakanin adaftan cibiyar sadarwa (ramummuka 63) da kuma abubuwan haɓakawa
Bayanan bayanan shigarwa da fitarwa sun dogara ne akan matsayin ramin da nau'in bayanai na ramin fadadawa. Yin odar shigarwa da fitarwa bayanan hoto yana dogara ne akan matsayi na faɗaɗawa. Lissafi don wannan tsari an haɗa su a cikin jagorar adaftar cibiyar sadarwa da na'urorin IO masu shirye-shirye.
Ingantattun bayanan siga ya dogara da samfuran da ake amfani da su. Domin misaliample, na'urorin analog suna da saitunan ko dai 0-20 mA ko 4-20 mA, kuma na'urorin zafin jiki suna da saituna kamar PT100, PT200, da PT500. Takaddun bayanai na kowane nau'i yana ba da bayanin bayanan siga.
Ƙayyadaddun bayanai
Ƙayyadaddun Muhalli
| Yanayin aiki | -20°C – 60°C |
| UL zafin jiki | -20°C – 60°C |
| Yanayin ajiya | -40°C – 85°C |
| Dangi zafi | 5%-90% ba condensing |
| Yin hawa | DIN dogo |
| Shock aiki | IEC 60068-2-27 (15G) |
| Juriya na rawar jiki | IEC 60068-2-6 (4 g) |
| Fitar masana'antu | EN 61000-6-4: 2019 |
| Kariyar masana'antu | EN 61000-6-2: 2019 |
| Matsayin shigarwa | A tsaye da a kwance |
| Takaddun shaida na samfur | CE, FCC, UL |
Gabaɗaya Bayani
| Rashin wutar lantarki | Max. 30mA @ 5 VDC |
| Kaɗaici | I/O zuwa dabaru: Warewa
Ikon filin: Rashin ware |
| UL filin iko | Ƙarar voltage: 24 VDC maras kyau, aji 2 |
| Ƙarfin filin | Ƙarar voltage: 24 VDC mai lamba Voltage kewayon: 18-30 VDC
Rashin wutar lantarki: 30mA @ 24 VDC |
| Waya | I/O na USB max. 2.0 mm2 (AWG 14) |
| Torque | 0.8 Nm (7Ib-in) |
| Nauyi | 59g ku |
| Girman module | 12 x 99 mm x 70 mm |
Girma
Girman Module (mm)
Ƙimar fitarwa
| Fitar kowane module | Tashoshi 4 sun ƙare, ba a ware tsakanin tashoshi |
| Manuniya (gefen dabaru) | 4 koren fitarwa matsayi |
| Ƙaddamarwa a cikin jeri | 16-bit: 0.31mV/bit |
| Kewayon fitarwa | - 10-10 V |
| Tsarin bayanai | lamba 16 bit (2' yabo) |
| Kuskuren Module | ± 0.1 % cikakken ma'auni @ 25 ℃
± 0.3 % cikakken ma'auni @ -40 °C, 60 ℃ |
| Juriya na lodi | Min 4 kΩ |
| Bincike | A kashe wutar filin: LED kyaftawar ido Ikon filin a kunne: Babu fitar da LED a kashe
Ƙarfin filin a kunne: Fitar da LED a kunne |
| Lokacin juyawa | 0.2 ms / duk tashoshi |
| Daidaitawa | Ba a buƙata |
| Nau'in gama gari | 4 tashoshi / 4 gama gari |
Tsarin Waya
| Fil babu. | Bayanin sigina |
| 0 | Analog tashar fitarwa 0 |
| 1 | Analog tashar fitarwa 1 |
| 2 | Analog tashar fitarwa 2 |
| 3 | Analog tashar fitarwa 3 |
| 4 | Tashar fitarwa ta gama gari (AGND) |
| 5 | Tashar fitarwa ta gama gari (AGND) |
| 6 | Tashar fitarwa ta gama gari (AGND) |
| 7 | Tashar fitarwa ta gama gari (AGND) |
| 8 | Tsarin ƙasa |
| 9 | Tsarin ƙasa |
Alamar LED
| LED no. | LED aiki / bayanin | LED launi |
| 0 | OUTPUT tashar 0 | Kore |
| 1 | OUTPUT tashar 1 | Kore |
| 2 | OUTPUT tashar 2 | Kore |
| 3 | OUTPUT tashar 3 | Kore |
Matsayin Tashoshin LED
| Matsayi | LED | Nuni |
| Aiki na al'ada | Kashe
Kore |
Babu ƙimar fitarwa
Aiki na al'ada |
| Kuskuren ikon filin | Duk tashar tana maimaita kore da kashewa | Ƙarfin filin ba ya haɗi |
Darajar Data / Voltage
Voltage kewayon: -10-10 VDC
| Voltage | -10.0 V | -5.0 V | 5.0 V | 10.0 V |
| Bayanai (Hex) | HF800 | HC000 | Farashin H3FFF | Farashin H7FFF |
Bayanin Taswira Daga Teburin Hoto
Ƙimar hoton da aka fitar
| Bit no. | Bit 7 | Bit 6 | Bit 5 | Bit 4 | Bit 3 | Bit 2 | Bit 1 | Bit 0 |
| Baiti 0 | Analog fitarwa Ch 0 low byte | |||||||
| Baiti 1 | Analog fitarwa Ch 0 babban byte | |||||||
| Baiti 2 | Analog fitarwa Ch 1 low byte | |||||||
| Baiti 3 | Analog fitarwa Ch 1 babban byte | |||||||
| Baiti 4 | Analog fitarwa Ch 2 low byte | |||||||
| Baiti 5 | Analog fitarwa Ch 2 babban byte | |||||||
| Baiti 6 | Analog fitarwa Ch 3 low byte | |||||||
| Baiti 7 | Analog fitarwa Ch 3 babban byte | |||||||
Bayanan fitarwa na module - bayanan fitarwa 8 byte
| Analog fitarwa Ch 0 |
| Analog fitarwa Ch 1 |
| Analog fitarwa Ch 2 |
| Analog fitarwa Ch 3 |
Bayanan Sigar
Tsawon siga mai inganci: 4 bytes
| Bit no. | Bit 7 | Bit 6 | Bit 5 | Bit 4 | Bit 3 | Bit 2 | Bit 1 | Bit 0 |
| Baiti 0 | Laifi na tashar 3 | Laifi na tashar 2 | Laifi na tashar 1 | Laifi na tashar 0 | ||||
| 00: Ƙimar kuskure / 01: Riƙe jihar ƙarshe / 10: Ƙananan iyaka / 11: Babban iyaka | ||||||||
| Baiti 1 | Ba a yi amfani da shi ba | |||||||
| Baiti 2 | Ƙimar ƙarancin ƙima | |||||||
| Baiti 3 | Ƙimar kuskure babban byte | |||||||
Saitin Hardware
HANKALI
- Koyaushe karanta wannan babin kafin shigar da tsarin!
- Zafi mai zafi! Fuskar gidan na iya zama zafi yayin aiki. Idan ana amfani da na'urar a cikin yanayin yanayin zafi, koyaushe bari na'urar ta yi sanyi kafin ta taɓa ta.
- Yin aiki akan na'urori masu ƙarfi na iya lalata kayan aiki! Koyaushe kashe wutar lantarki kafin aiki akan na'urar.
Bukatun sararin samaniya
Zane-zane masu zuwa suna nuna buƙatun sarari lokacin shigar da samfuran G-jerin. Tazarar tana haifar da sarari don samun iska, kuma yana hana tsangwama na lantarki da aka gudanar daga yin tasiri. Matsayin shigarwa yana aiki a tsaye da a kwance. Hotunan misalai ne kuma maiyuwa ba su kai daidai ba.
HANKALI
RASHIN bin buƙatun sarari na iya haifar da ɓata samfurin.
Dutsen Module zuwa DIN Rail
Babi masu zuwa suna bayyana yadda ake hawan tsarin zuwa dogo na DIN.
HANKALI
Dole ne a daidaita tsarin zuwa layin dogo na DIN tare da maƙallan kullewa.
Dutsen GL-9XXX ko GT-XXXX Module
Umurnai masu zuwa sun shafi waɗannan nau'ikan samfura:
- GL-9XXX
- GT-1XXX
- GT-2XXX
- GT-3XXX
- GT-4XXX
- GT-5XXX
- GT-7XXX
Modulolin GN-9XXX suna da levers na kulle guda uku, ɗaya a ƙasa da biyu a gefe. Don umarnin hawa, koma zuwa Module Dutsen GN-9XXX.
Module Dutsen GN-9XXX
Don hawa ko saukar da adaftar cibiyar sadarwa ko tsarin IO mai tsari tare da sunan samfurin GN-9XXX, don ex.ampGN-9251 ko GN-9371, duba waɗannan umarnin:
Tushen Tasha Mai Cirewa
Don hawa ko saukar da toshe mai cirewa (RTB), duba umarnin da ke ƙasa.
Haɗa igiyoyi zuwa Toshe Tasha Mai Cirewa
Don haɗa/cire haɗin igiyoyi zuwa/daga cikin toshe mai cirewa (RTB), duba umarnin da ke ƙasa.
GARGADI
Koyaushe amfani da shawarar samarwa voltage da mita don hana lalacewar kayan aiki da kuma tabbatar da kyakkyawan aiki.
Wurin Wuta da Fil ɗin Bayanai
Sadarwa tsakanin adaftar cibiyar sadarwa ta G-jerin da tsarin faɗaɗawa, da tsarin / filin samar da wutar lantarki na motocin bas ana aiwatar da su ta hanyar bas na ciki. Ya ƙunshi Fil Power Fil 2 da Fin bayanai 6.
GARGADI
Kar a taɓa bayanan da filayen ikon filin! Taɓawa na iya haifar da lalacewa da lalacewa ta hanyar hayaniyar ESD.
| Fil babu. | Suna | Bayani |
| P1 | Tsarin VCC | Samar da tsarin voltage (5VDC) |
| P2 | Tsarin GND | Tsarin ƙasa |
| P3 | Fitowar alama | Token fitarwa tashar jiragen ruwa na processor module |
| P4 | Serial fitarwa | Mai watsa fitarwa tashar jiragen ruwa na processor module |
| P5 | Shigar da serial | Mai shigar da tashar tashar mai karɓar mai sarrafawa |
| P6 | Ajiye | An tanada don alamar wucewa |
| P7 | Filin GND | Filin filin |
| P8 | Filin VCC | Samar da filin voltage (24VDC) |
Bayanin da ke cikin wannan takarda yana iya canzawa ba tare da sanarwa ba kuma ana bayar da shi kamar yadda yake a lokacin bugawa. Beijer Electronics AB yana da haƙƙin canza kowane bayani ba tare da sabunta wannan ɗaba'ar ba. Beijer Electronics AB ba ta da alhakin kowane kurakurai da ka iya bayyana a cikin wannan takarda. Duk examples a cikin wannan takarda an yi niyya ne kawai don inganta fahimtar ayyuka da sarrafa kayan aiki. Beijer Electronics AB ba zai iya ɗaukar kowane alhaki ba idan waɗannan tsoffinampAna amfani da les a ainihin aikace-aikace.
In view daga cikin nau'ikan aikace-aikacen wannan software, masu amfani dole ne su sami isasshen ilimi da kansu don tabbatar da cewa an yi amfani da shi daidai a takamaiman aikace-aikacen su. Mutanen da ke da alhakin aikace-aikacen da kayan aiki dole ne da kansu su tabbatar da cewa kowane aikace-aikacen ya dace da duk buƙatun da suka dace, ƙa'idodi, da dokoki dangane da tsari da aminci. Beijer Electronics AB ba za ta karɓi wani alhaki ga duk wani lahani da ya faru yayin shigarwa ko amfani da kayan aiki da aka ambata a cikin wannan takarda. Beijer Electronics AB ya haramta duk gyare-gyare, canje-canje, ko canza kayan aiki.
Karin Bayani
Babban ofishi
Beijer Electronics AB girma
Akwatin 426
201 24 Malmö, Sweden
- www.beijerelectronics.com
- + 46 40 358600
FAQ
- Tambaya: Menene zan yi idan na gamu da kuskure yayin amfani da Analog Fitar Module?
- A: Idan kun ci karo da kurakurai, da farko koma zuwa littafin mai amfani don shawarwarin warware matsala. Tabbatar da shigarwa da daidaitawa daidai. Idan al'amura sun ci gaba, tuntuɓi tallafin abokin ciniki don ƙarin taimako.
- Tambaya: Zan iya amfani da Module Output Analog tare da wasu tsarin baya ga jerin G?
- A: Module Output Analog an tsara shi musamman don amfani da tsarin G-jerin. Daidaituwa da wasu tsarin na iya bambanta, don haka ana ba da shawarar bincika tare da masana'anta don bayanin dacewa.
Takardu / Albarkatu
 |
Beijer ELECTRONICS GT-4564 Analog Fitar Module [pdf] Manual mai amfani GT-4564 Analog Output Module, GT-4564, Analog Fitar Module, Fitar Module, Module |