I-ARDUINO ABX00087 UNO R4 WiFi
Ulwazi lweMveliso
IMveliso yeReference Manual SKU: IABX00087
Inkcazo: Iindawo ekujoliswe kuzo: Umenzi, umqali, imfundo
Iimbonakalo:
- I-R7FA4M1AB3CFM#AA0, edla ngokubizwa ngokuba yi-RA4M1 kolu luhlu lwedatha, yeyona MCU iphambili kwi-UNO R4 WiFi, eqhagamshelwe kuzo zonke iiheader zepin kwibhodi kwakunye nazo zonke iibhasi zonxibelelwano.
- Imemori: 256 kB iMemori yeFlash, 32 kB SRAM, 8 kB iMemori yeDatha (EEPROM)
- Iiperipherals: ICapacitive Touch Sensing Unit (CTSU), USB 2.0 Full-Speed Module (USBFS), 14-bit ADC, Ukuya kuthi ga kwi-12-bit DAC,Iyasebenza Ampisihlanguli (OPAMP)
- Unxibelelwano: 1x UART (pin D0, D1), 1x SPI (pin D10-D13, ICSP header), 1x I2C (pin A4, A5, SDA, SCL), 1x CAN (pin D4, D5,i-transceiver yangaphandle iyadingeka)
Ukufumana iinkcukacha ezithe kratya zobugcisa kwi-R7FA4M1AB3CFM#AA0 microcontroller, tyelela i R7FA4M1AB3CFM#AA0 datasheet.
Iimpawu ze-ESP32-S3-MINI-1-N8:
- Le modyuli isebenza njenge-MCU yesibini kwi-UNO R4 WiFi kwaye inxibelelana ne-RA4M1 MCU isebenzisa umguquli wenqanaba lengqiqo.
- Qaphela ukuba le modyuli isebenza kwi-3.3 V ngokuchasene ne-RA4M1's 5 V yevolthi yokusebenza.tage.
Ukufumana iinkcukacha ezithe vetshe ngobugcisa kwimodyuli ye-ESP32-S3-MINI-1-N8, tyelela i Idatha ye-ESP32-S3-MINI-1-N8.
Imiyalelo yokusetyenziswa kwemveliso
Imiqathango yokuSebenza eCetyisiweyo:
| Uphawu | Inkcazo | Min | Chwetheza | Max |
|---|---|---|---|---|
| VIN | Igalelo voltage ukusuka VIN pad / DC Jack | 6 | 7.0 | 24 |
| I-VUSB | Igalelo voltage ukusuka kwisidibanisi se-USB | 4.8 | 5.0 | 5.5 |
| PHEZULU | Ubushushu bokusebenza | -40 | 25 | 85 |
Umsebenzi oPhezuluview:
Umthamo wokusebenzatagI-e ye-RA4M1 igxininiswe kwi-5 V ukuba ibe yi-hardware ehambelana nezihlangu, izixhobo, kunye neesekethe ezisekelwe kwiibhodi ze-UNO zangaphambili ze-Arduino.
I-Topology yeBhodi:
Ngaphambili View:
Ref. U1 U2 U3 U4 U5 U6 U_LEDMATRIX M1 PB1 JANALOG JDIGITAL JOFF J1 J2 J3 J5 J6 DL1
Phezulu View:
Ref. I-DL2 LED RX (i-serial yamkela), i-DL3 Amandla e-LED (eluhlaza), i-DL4 LED SCK (i-serial clock), i-D1 PMEG6020AELRX Schottky Diode, i-D2 PMEG6020AELRX Schottky Diode, i-D3 PRTR5V0U2X, i-215 yoKhuselo lwe-ESD
Okubhalwe ngasentla kwe-ESP:
Iheda ebekwe kufutshane neqhosha le-RESET ingasetyenziselwa ukufikelela kwimodyuli ye-ESP32-S3 ngokuthe ngqo. Izikhonkwane ezifikelelekayo zezi:
- ESP_IO42 – MMS ukulungisa ingxaki (iPin 1)
- ESP_IO41 – MTDI debugging (Pin 2)
- ESP_TXD0 – Ukuhanjiswa kothotho (UART) (Iphini 3)
- ESP_DOWNLOAD – qalisa (iPin 4)
- ESP_RXD0 – Uthotho Fumana (UART) (Pin 5)
- GND - umhlaba (Iphini 6)
Inkcazo
I-Arduino® UNO R4 WiFi yibhodi yokuqala ye-UNO ebonisa i-32-bit microcontroller kunye nemodyuli ye-ESP32-S3 Wi-Fi® (ESP32-S3-MINI-1-N8). Ibonisa i-RA4M1 yochungechunge lwe-microcontroller evela kwi-Renesas (R7FA4M1AB3CFM#AA0), esekelwe kwi-48 MHz Arm® Cortex®-M4 microprocessor. Inkumbulo ye-WiFi ye-UNO R4 inkulu kunangaphambili, ine-256 kB flash, 32 kB SRAM kunye ne-8 kB ye-EEPROM.
I-RA4M1's voltage ilungiswe kwi-5 V, kanti imodyuli ye-ESP32-S3 yi-3.3 V. Unxibelelwano phakathi kwezi MCU zimbini lwenziwa nge-logic level translator (TXB0108DQSR).
Iindawo ekujoliswe kuzo:
Umenzi, umqali, imfundo
Iimbonakalo
I-R7FA4M1AB3CFM#AA0, edla ngokubizwa ngokuba yi-RA4M1 kolu luhlu lwedatha, yeyona MCU iphambili kwi-UNO R4 WiFi, eqhagamshelwe kuzo zonke iiheader zepin kwibhodi kwakunye nazo zonke iibhasi zonxibelelwano.
Ngaphezuluview
- 48 MHz Arm® Cortex®-M4 microprocessor enendawo edadayo yeyunithi (FPU) 5 V yevolthi yokusebenzatage
- Iwotshi yexesha lokwenyani (RTC)
- IYunithi yoKhuseleko lweMemori (MPU)
- Digital-to-analog Converter (DAC)
Inkumbulo
- 256 kB Inkumbulo yokudanyaza
- 32 kB SRAM
- 8 kB iMemori yeDatha (EEPROM)
Iiperipherals
- ICapacitive Touch Sensing Unit (CTSU)
- I-USB 2.0 iModyuli eSpeed esiPheleleyo (USBFS)
- I-14-bit ADC
- Ukuya kuthi ga kwi-12-bit DAC
- Ukusebenza Ampinqanawa (OPAMP)
Amandla
- Ukusebenza ivoltagI-e ye-RA4M1 yi-5 V
- Igalelo elicetyiswayo voltage (VIN) yi-6-24 V
- Ijekhi yomphanda iqhagamshelwe kwi-VIN pin (6-24 V)
- Amandla nge-USB-C® nge-5 V
Unxibelelwano
- 1x UART (pin D0, D1)
- I-1x SPI (i-pin D10-D13, i-header ye-ICSP)
- 1x I2C (pin A4, A5, SDA, SCL)
- I-1x CAN (i-pin D4, i-D5, i-transceiver yangaphandle iyafuneka)
Jonga idatha yedatha ye-R7FA4M1AB3CFM#AA0 kwikhonkco elingezantsi:
- R7FA4M1AB3CFM#AA0 datasheet
I-ESP32-S3-MINI-1-N8 yi-MCU yesibini kunye ne-antenna eyakhelweyo kwi-Wi-Fi® kunye neBluetooth® uxhumano. Le modyuli isebenza kwi-3.3 V kwaye inxibelelana ne-RA4M1 isebenzisa umguquleli wenqanaba le-logic (TXB0108DQSR).
Ngaphezuluview
- Xtensa® dual-core 32-bit LX7 microprocessor
- 3.3 V ukusebenza voltage
- 40 MHz crystal oscillator
I-Wi-Fi®
- Inkxaso ye-Wi-Fi® ene-802.11 b/g/n esemgangathweni (Wi-Fi® 4)
- Isantya seBit ukuya kuthi ga kwi-150 Mbps
- 2.4 GHz ibhendi
I-Bluetooth®
- I-Bluetooth® 5
Jonga i-database epheleleyo ye-ESP32-S3-MINI-1-N8 kwikhonkco elingezantsi:
- Idatha ye-ESP32-S3-MINI-1-N8
Ibhodi
Isicelo ExampLes
I-UNO R4 WiFi yinxalenye yochungechunge lokuqala lwe-UNO lweebhodi zophuhliso lwe-32-bit, ezisekelwe ngaphambili kwi-8-bit AVR microcontrollers. Kukho amawaka ezikhokelo, izifundo kunye neencwadi ezibhaliweyo malunga nebhodi ye-UNO, apho i-UNO R4 WiFi iqhubeka nelifa layo.
Ibhodi ibonisa i-14 ye-digital I / O izibuko, iziteshi ze-analog ze-6, izikhonkwane ezinikezelweyo ze-I2C, i-SPI kunye ne-UART. Inenkumbulo enkulu kakhulu: inkumbulo yeflash amaxesha ayi-8 ngaphezulu (256 kB) kunye namaxesha ali-16 ngaphezulu kweSRAM (32 kB). Ngesantya sewotshi ye-48 MHz, ikwayi-3x ngokukhawuleza kunangaphambili.
Ukongeza, ifaka imodyuli ye-ESP32-S3 ye-Wi-Fi® kunye neBluetooth® ukuqhagamshelwa, kunye ne-12 × 8 ye-matrix ye-LED eyakhelweyo, eyenza enye yebhodi ye-Arduino ebonakalayo ebonakalayo ukuza kuthi ga ngoku. I-matrix ye-LED icwangciswe ngokupheleleyo, apho unokulayisha nantoni na ukusuka kwizakhelo ezimileyo ukuya koopopayi besiko.
Iiprojekthi zomgangatho wokungena: Ukuba le yiprojekthi yakho yokuqala kwikhowudi nakwizinto zombane, i-UNO R4 WiFi ifanelekile. Kulula ukuqalisa ngayo, kwaye inamaxwebhu amaninzi akwi-intanethi.
Usetyenziso olulula lwe-IoT: ukwakha iiprojekthi ngaphandle kokubhala nayiphi na ikhowudi yenethiwekhi kwi-Arduino IoT Cloud. Jonga ibhodi yakho, uyidibanise nezinye iibhodi kunye neenkonzo, kwaye uphuhlise iiprojekthi ezipholileyo ze-IoT.
IMatrix ye-LED: I-12 × 8 matrix ye-LED ebhodini inokusetyenziselwa ukubonisa oopopayi, ukuskrola okubhaliweyo, ukwenza imidlalo emincinci kunye nokunye okuninzi, ibe luphawu olugqibeleleyo ukunika iprojekthi yakho ubuntu obungakumbi.
Iimveliso ezinxulumeneyo
- UNO R3
- UNO R3 SMD
- UNO R4 Minima
Ukukala
IiMeko zokuSebenza eziCetyisiweyo
| Uphawu | Inkcazo | Min | Chwetheza | Max | Iyunithi |
| VIN | Igalelo voltage ukusuka VIN pad / DC Jack | 6 | 7.0 | 24 | V |
| I-VUSB | Igalelo voltage ukusuka kwisidibanisi se-USB | 4.8 | 5.0 | 5.5 | V |
| PHEZULU | Ubushushu bokusebenza | -40 | 25 | 85 | °C |
Phawula: I-VDD ilawula inqanaba lengqiqo kwaye iqhagamshelwe kwi-5V kaloliwe yamandla. I-VAREF yeye-analog logic.
Umsebenzi oPhezuluview
Umzobo weBhloko
I-Topology yeBhodi
Ngaphambili View
| Ref. | Inkcazo |
| U1 | R7FA4M1AB3CFM#AA0 Microcontroller IC |
| U2 | I-NLASB3157DFT2G Multiplexer |
| U3 | I-ISL854102FRZ-T Isiguquli seBuck |
| U4 | I-TXB0108DQSR isiguquli senqanaba lengqiqo (5 V – 3.3 V) |
| U5 | SGM2205-3.3XKC3G/TR 3.3 V isilawuli somgca |
| U6 | I-NLASB3157DFT2G Multiplexer |
| U_LEDMATRIX | I-12 × 8 i-Matrix ebomvu ye-LED |
| M1 | ESP32-S3-MINI-1-N8 |
| PB1 | UKUSETA BUYA iqhosha |
| JANALOG | Igalelo le-analog/imveliso yezihloko |
| I-JDIGITAL | Igalelo ledijithali/izihloko zemveliso |
| JOFF | CIMA, i-header ye-VRTC |
| J1 | CX90B-16P USB-C® isidibanisi |
| J2 | SM04B-SRSS-TB(LF)(SN) I2C isidibanisi |
| J3 | Iheda ye-ICSP (SPI) |
| J5 | DC Jack |
| J6 | Okubhalwe ngasentla kwe-ESP |
| DL1 | I-LED TX (i-serial transmit) |
| DL2 | I-LED RX (uthotho yamkela) |
| DL3 | Amandla e-LED (luhlaza) |
| DL4 | I-LED SCK (ikloko yothotho) |
| D1 | I-PMEG6020AELRX Schottky Diode |
| D2 | I-PMEG6020AELRX Schottky Diode |
| D3 | PRTR5V0U2X,215 Ukhuseleko lwe-ESD |
Microcontroller (R7FA4M1AB3CFM#AA0)
I-UNO R4 WiFi isekwe kuluhlu lwe-32-bit RA4M1 microcontroller, R7FA4M1AB3CFM#AA0, esuka eRenesas, esebenzisa i-48 MHz Arm® Cortex®-M4 microprocessor eneyunithi edadayo (FPU).
Umthamo wokusebenzatage-RA4M1 ilungiswe kwi-5 V ukuze ibe yi-hardware ehambelanayo namakhaka, izincedisi kunye neesekethe ezisekelwe kwiibhodi ze-UNO zangaphambili ze-Arduino.
The R7FA4M1AB3CFM#AA0 features:
- 256 kB iflash / 32 kB SRAM / 8 kB iflash yedatha (EEPROM)
- Iwotshi yexesha lokwenyani (RTC)
- 4x isiLawuli esiNgqo ngoFikelelo kwiMemori (DMAC)
- I-14-bit ADC
- Ukuya kuthi ga kwi-12-bit DAC
- OPAMP
- CAN ibhasi
Ukufumana iinkcukacha ezithe vetshe ngobuchule kwesi silawuli sincinci, ndwendwela iRenesas – RA4M1 uluhlu lwamaxwebhu asemthethweni.
6 Wi-Fi® / Bluetooth® Imodyuli (ESP32-S3-MINI-1-N8)
Imodyuli yeWi-Fi® / Bluetooth® LE kwi-UNO R4 WiFi ivela kwii-ESP32-S3 SoCs. Ifaka i-Xtensa® dual-core 32-bit LX7 MCU, i-eriyali eyakhelweyo kunye nenkxaso yeebhendi ze-2.4 GHz.
Iimpawu ze-ESP32-S3-MINI-1-N8:
- Wi-Fi® 4 – 2.4 GHz ibhendi
- Inkxaso yeBluetooth® 5 LE
- 3.3 V ukusebenza voltage 384 kB ROM
- 512 kB SRAM
- Ukuya kuthi ga kwi-150 Mbps ireyithi yebit
Le modyuli isebenza njenge-MCU yesibini kwi-UNO R4 WiFi, kwaye inxibelelana ne-RA4M1 MCU isebenzisa umguquli wenqanaba lengqiqo. Qaphela ukuba le modyuli isebenza kwi-3.3 V ngokuchasene ne-RA4M1's 5 V yevolthi yokusebenza.tage.
ESP Header
Iheda ebekwe kufutshane neqhosha le-RESET ingasetyenziselwa ukufikelela kwimodyuli ye-ESP32-S3 ngokuthe ngqo. Izikhonkwane ezifikelelekayo zezi:
- ESP_IO42 – MMS ukulungisa ingxaki (iPin 1)
- ESP_IO41 – MTDI debugging (Pin 2)
- ESP_TXD0 – Ukuhanjiswa kothotho (UART) (Iphini 3)
- ESP_DOWNLOAD – qalisa (iPin 4)
- ESP_RXD0 – Uthotho Fumana (UART) (Pin 5)
- GND - umhlaba (Iphini 6)
Ibhulorho ye-USB
Xa kusenziwa inkqubo ye-UNO R4 WiFi, i-RA4M1 MCU icwangciswe ngemodyuli ye-ESP32-S3 ngokungagqibekanga. Ukutshintsha kwe-U2 kunye ne-U6 kunokutshintsha unxibelelwano lwe-USB ukuya ngqo kwi-RA4M1 MCU, ngokubhala umgangatho ophezulu kwi-P408 pin (D40).
Ukuthengisa ndawonye iipads ze-SJ1 kusetha ngokusisigxina unxibelelwano lwe-USB ngqo kwi-RA4M1, ngokudlula i-ESP32-S3.
Isinxibelelanisi se-USB
I-UNO R4 WiFi inezibuko le-USB-C® enye, esetyenziselwa ukunika amandla kunye neprogram yebhodi yakho kunye nokuthumela kunye nokufumana unxibelelwano olulandelelanayo.
Qaphela: Ibhodi akufanele inikwe amandla angaphezu kwe-5 V nge-USB-C® port.
LED Matrix
I-UNO R4 WiFi ine-matrix eyi-12×8 yee-LED ezibomvu (U_LEDMATRIX), edityaniswe kusetyenziswa ubuchule obaziwa ngokuba yi-charlieplexing.
Ezi zikhonkwane zilandelayo kwi-RA4M1 MCU zisetyenziselwa imatrix:
- P003
- P004
- P011
- P012
- P013
- P015
- P204
- P205
- P206
- P212
- P213
Ezi LEDs zinokufumaneka njenge-array, usebenzisa ithala leencwadi elithile. Jonga imephu engezantsi:
Le matrix ingasetyenziselwa inani leeprojekthi kunye neenjongo zeprototyping, kwaye ixhasa oopopayi, uyilo olulula lomdlalo kunye nokuskrola okubhaliweyo phakathi kwezinye izinto.
Isiguquli seAnalog yeDijithali (DAC)
I-UNO R4 WiFi ine-DAC enesisombululo se-12-bit esiqhotyoshelwe kwi-pin ye-analog ye-A0. I-DAC isetyenziselwa ukuguqula umqondiso wedijithali kwisignali ye-analog.
I-DAC ingasetyenziselwa ukuvelisa umqondiso umz. usetyenziso lwe-audio, njengokuvelisa nokuguqula amaza e-sawtooth.
I2C Isidibanisi
Isixhumi se-I2C i-SM04B-SRSS-TB (LF) (SN) idibaniswe nebhasi ye-I2C yesibini ebhodini. Qaphela ukuba esi sidibanisi sinikwe amandla nge-3.3 V.
Esi sidibanisi sikwabelana ngezi khonkco zilandelayo:
JANALOG umbhalo ongasentla kwekhasi
- A4
- A5
JDIGITAL okubhalwe ngasentla kwekhasi
- SDA
- I-SCL
Phawula: njengoko i-A4/A5 iqhagamshelwe kwibhasi ye-I2C engundoqo, ezi azifanele zisetyenziswe njengamagalelo e-ADC nanini na xa ibhasi isetyenziswa. Nangona kunjalo ungaqhagamshela izixhobo ze-I2C kwisikhonkwane ngasinye kwezi kunye nezihlanganisi ngaxeshanye.
Iinketho zamandla
Amandla anokuthi anikezelwe nge-VIN pin, okanye nge-USB-C® ikhonkco. Ukuba amandla anikezelwe ngeVIN, i-ISL854102FRZ isiguquli sebhanti sinyathela ivolthitagezantsi ukuya ku5V.
Zombini izikhonkwane ze-VUSB kunye ne-VIN ziqhagamshelwe kwi-ISL854102FRZ buck converter, kunye ne-Schottky diode endaweni yokubuyela umva polarity & overvol.tage ukhuseleko ngokulandelelanayo.
Amandla ngokubonelela nge-USB malunga ne- ~ 4.7 V (ngenxa ye-Schottky drop) ukuya kwi-RA4M1 MCU.
Umlawuli we-linear (SGM2205-3.3XKC3G/TR) uguqula i-5 V ukusuka kwi-buck converter okanye i-USB, kwaye inikezela nge-3.3 V kwinani lamacandelo, kuquka imodyuli ye-ESP32-S3.
Umthi wamandla
I-Pin Voltage
Umsebenzi jikelele voltagI-e ye-UNO R4 WiFi yi-5 V, nangona kunjalo imodyuli ye-ESP32-S3 yokusebenza kwevolthitage yi 3.3V.
Phawula: Kubaluleke kakhulu ukuba izikhonkwane ze-ESP32-S3 (3.3 V) zingadibani nazo naziphi na izikhonkwane ze-RA4M1 (5 V), njengoko oku kungonakalisa iisekethe.
I-Pin yangoku
I-GPIOs kwi-R7FA4M1AB3CFM#AA0 microcontroller inokuphatha ngokukhuselekileyo ukuya kuthi ga kwi-8 mA yangoku. Ungaze uqhagamshele izixhobo ezitsala umsinga ophezulu ngokuthe ngqo kwi-GPIO njengoko oku kungonakalisa isekethi.
Ukunika amandla umzekelo iinjini ze-servo, soloko usebenzisa unikezelo lwamandla lwangaphandle.
Ulwazi ngoomatshini
I-Pinout
I-Analog
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | BHUKU | NC | AyiQhagamshelwanga |
| 2 | IOREF | IOREF | Isalathiso sengqiqo yedijithali V – eqhagamshelwe kwi-5 V |
| 3 | Lungisa kwakhona | Lungisa kwakhona | Lungisa kwakhona |
| 4 | +3V3 | Amandla | +3V3 Isiporo saMandla |
| 5 | +5V | Amandla | +5V kaloliwe wamandla |
| 6 | GND | Amandla | Umhlaba |
| 7 | GND | Amandla | Umhlaba |
| 8 | VIN | Amandla | UmqulutagIgalelo |
| 9 | A0 | I-Analog | Igalelo leAnalog 0 / DAC |
| 10 | A1 | I-Analog | Igalelo le-analog 1 / OPAMP+ |
| 11 | A2 | I-Analog | Igalelo le-analog 2 / OPAMP- |
| 12 | A3 | I-Analog | Igalelo le-analog 3 / OPAMPNgaphandle |
| 13 | A4 | I-Analog | Igalelo leAnalog 4 / I2C Uthotho lweDatha (SDA) |
| 14 | A5 | I-Analog | Igalelo le-Analog 5 / I2C Uthotho lweClock (SCL) |
Idijithali
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | I-SCL | Idijithali | I2C Series Clock (SCL) |
| 2 | SDA | Idijithali | I2C Uthotho lweDatha (SDA) |
| 3 | I-AREF | Idijithali | I-Analog Reference Voltage |
| 4 | GND | Amandla | Umhlaba |
| 5 | D13/SCK/CANRX0 | Idijithali | GPIO 13 / SPI Clock / CAN Umamkeli (RX) |
| 6 | D12/CIPO | Idijithali | I-GPIO 12 / Isilawuli se-SPI kwi-Peripheral Out |
| 7 | D11/COPI | Idijithali | I-GPIO 11 (PWM) / Isilawuli se-SPI ngaphandle kwePeripheral In |
| 8 | D10/CS/CANTX0 | Idijithali | GPIO 10 (PWM) / SPI Chip Khetha / CAN Transmitter (TX) |
| 9 | D9 | Idijithali | GPIO 9 (PWM~) |
| 10 | D8 | Idijithali | GPIO 8 |
| 11 | D7 | Idijithali | GPIO 7 |
| 12 | D6 | Idijithali | GPIO 6 (PWM~) |
| 13 | D5 | Idijithali | GPIO 5 (PWM~) |
| 14 | D4 | Idijithali | GPIO 4 |
| 15 | D3 | Idijithali | GPIO 3 (PWM~) |
| 16 | D2 | Idijithali | GPIO 2 |
| 17 | D1/TX0 | Idijithali | GPIO 1 / Uthotho 0 Transmitter (TX) |
| 18 | D0/TX0 | Idijithali | GPIO 0 / Uthotho 0 Umamkeli (RX) |
CIMA
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | CIMA | Amandla | Kulawulo lonikezelo lwamandla |
| 2 | GND | Amandla | Umhlaba |
| 1 | I-VRTC | Amandla | Uqhagamshelo lwebhetri kumandla e-RTC kuphela |
I-ICSP
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | CIPO | Ngaphakathi | Umlawuli Kwi-peripheral Out |
| 2 | +5V | Ngaphakathi | Ubonelelo lwaMandla lwe5V |
| 3 | I-SCK | Ngaphakathi | Ikloko yothotho |
| 4 | I-COPI | Ngaphakathi | Umlawuli ngaphandle kwe-peripheral In |
| 5 | SETSHENZISWA KHONA | Ngaphakathi | Lungisa kwakhona |
| 6 | GND | Ngaphakathi | Umhlaba |
Imingxunya yokuQinisa kunye nolwandlalo lweBhodi
Ukusebenza kweBhodi
- Ukuqalisa – IDE
Ukuba ufuna ukucwangcisa i-UNO R4 WiFi yakho ngelixa ungaxhunyiwe kwi-intanethi kufuneka ufake i-Arduino® Desktop IDE [1]. Ukuqhagamshela i-UNO R4 WiFi kwikhompyutheni yakho, uya kufuna intambo ye-USB ye-Type-C®, enokunika amandla ebhodini, njengoko kuboniswe yi-LED (DL1). - Ukuqalisa - Arduino Web Umhleli
Zonke iibhodi zeArduino, kuquka nale, zisebenza ngaphandle kwebhokisi kwiArduino® Web Umhleli [2], ngokufaka nje iplagi elula.
IArduino Web Umhleli ubanjwa kwi-intanethi, ke ngoko iya kuhlala isexesheni ngeempawu zamva nje kunye nenkxaso yazo zonke iibhodi. Landela [3] ukuqalisa ukubhala ikhowudi kwisikhangeli kwaye ulayishe imizobo yakho ebhodini yakho. - Ukuqalisa-i-Arduino IoT Cloud
Zonke iimveliso ezinikwe amandla ze-Arduino IoT zixhaswa kwi-Arduino IoT Cloud ekuvumela ukuba ungene, igrafu kwaye uhlalutye idatha yenzwa, uqalise iziganeko, kwaye uzenzele ikhaya lakho okanye ishishini. - Izixhobo ezikwi-Intanethi
Ngoku ukuba udlule kwizinto ezisisiseko onokuthi uzenze ngebhodi unokuhlola amathuba angenasiphelo ebonelela ngokujonga iiprojekthi ezikhoyo kwi-Arduino Project Hub [4], i-Arduino Library Reference [5], kunye nevenkile ye-intanethi [6] ]; apho uya kuba nakho ukuncedisana nebhodi yakho kunye nabenzi boluvo, ii-activators kunye nokunye. - UkuBuyiselwa kweBhodi
Zonke iibhodi zeArduino zine-bootloader eyakhelwe-ngaphakathi evumela ukuba idanyaze ibhodi nge-USB. Kwimeko apho umzobo utshixa iprosesa kwaye ibhodi ayifumaneki kwakhona nge-USB, kunokwenzeka ukuba ufake imowudi yokuqalisa ngokucofa kabini iqhosha lokuseta kwakhona emva kokufakwa kwamandla.
Iziqinisekiso
15 isiBhengezo sokuThobela i-CE DoC (EU)
Sibhengeza phantsi koxanduva lwethu ukuba ezi mveliso zingentla zihambelana neemfuno ezingundoqo zale Miqathango ilandelayo ye-EU kwaye ke ngoko sikulungele ukuhamba ngokukhululekileyo kwiimarike ezibandakanya aseYurophu.
IManyano (EU) kunye noMmandla woQoqosho waseYurophu (EEA).
16 Isibhengezo sokuThobela kwi-EU RoHS & REACH 211 01/19/2021
Iibhodi ze-Arduino zihambelana ne-RoHS 2 Directive 2011/65/EU yePalamente yaseYurophu kunye ne-RoHS 3 Directive 2015/863/EU yeBhunga le-4 kaJuni 2015 ekuthinteleni ukusetyenziswa kwezinto ezithile ezinobungozi kwisixhobo sombane kunye ne-elektroniki.
| Iziyobisi | Ubuninzi bomda (ppm) |
| Khokela (Pb) | 1000 |
| I-Cadmium (Cd) | 100 |
| Imercury (HG) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Iibiphenyls zePoly Brominated (PBB) | 1000 |
| I-Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| I-Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| I-Benzyl butyl phthalate (BBP) | 1000 |
| I-Dibutyl phthalate (DBP) | 1000 |
| I-Diisobutyl phthalate (DIBP) | 1000 |
Ukukhululwa : Akukho kukhululwa kubangwayo.
Iibhodi ze-Arduino zihambelana ngokupheleleyo neemfuno ezihambelanayo ze-European Union Regulation (EC) 1907 / 2006 malunga noBhaliso, uVavanyo, uGunyaziso kunye nokuThintelwa kweMichiza (REACH). Sibhengeza ukuba akukho nanye kwii-SVHCs (https://echa.europa.eu/web/undwendwe/itheyibhile yoluhlu lwabagqatswa), uLuhlu lwaBaviwa beZinto eziNxibeleleyo ngokuPhakeme kakhulu ngokugunyaziswa ngoku ekhutshwe yi-ECHA, ikhona kuzo zonke iimveliso (kunye nephakheji) ngobuninzi obupheleleyo kuxinzelelo olulingana okanye ngaphezulu kwe-0.1%. Ngokolwazi lwethu, sikwabhengeza ukuba iimveliso zethu aziqulathanga naziphi na izinto ezidweliswe “kuLuhlu loGunyaziso” (Isihlomelo XIV semigaqo ye-REACH) kunye neZinto eziXhatha kakhulu (SVHC) kuyo nayiphi na imali ebalulekileyo njengoko ichaziwe. ngeSihlomelo XVII soluhlu lwabaMviwa olupapashwe yi-ECHA (i-Arhente yeMichiza yaseYurophu) 1907 /2006/EC.
Ungquzulwano lweZimbiwa isibhengezo
Njengomthengisi wehlabathi jikelele wezinto zombane kunye nombane, i-Arduino iyazazi izibophelelo zethu ngokubhekiselele kwimithetho nemimiselo malunga neMinerals ye-Conflict, ngokukodwa i-Dodd-Frank Wall Street Reform kunye ne-Consumer Protection Act, iCandelo 1502. I-Arduino ayiveli ngokuthe ngqo okanye iqhube ingxabano iiminerali ezifana neTin, iTantalum, iTungsten, okanye iGolide. Iiminerali eziphikisanayo ziqulethwe kwiimveliso zethu ngendlela ye-solder, okanye njengecandelo kwi-alloys zetsimbi. Njengenxalenye yenkuthalo yethu efanelekileyo, i-Arduino iqhagamshelane nabanikezeli becandelo ngaphakathi kwekhonkco lethu lokubonelela ukuqinisekisa ukuqhubeka kwabo ukuthobela imimiselo. Ngokusekelwe kulwazi esilufumeneyo ukuza kuthi ga ngoku, sibhengeza ukuba iimveliso zethu ziqulathe iziMbiwa zoNgqubano ezithathwe kwiindawo ezingenazingxabano.
Isilumkiso seFCC
Naluphi na uTshintsho okanye uhlengahlengiso olungavunywanga ngokucacileyo liqela elinoxanduva lokuthotyelwa lunokuphelisa igunya lomsebenzisi lokusebenzisa isixhobo.
Esi sixhobo sithobela inxalenye ye-15 yeMithetho yeFCC. Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo sisenokungabangeli uphazamiseko oluyingozi
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko olufunyenweyo, kuquka uphazamiseko olunokubangela usetyenziso olungafunekiyo.
INkcazo yeFCC RF yokuVela kwiMitha:
- Esi siThuthi akufuneki sibe kwindawo enye okanye sisebenze kunye nayo nayiphi na enye i-eriyali okanye isidluliseli.
- Esi sixhobo sithobela imida yokuvezwa kwemitha ye-RF emiselwe indawo engalawulwayo.
- Esi sixhobo kufuneka sifakwe kwaye sisebenze kunye nomgama omncinci wama-20 cm phakathi kweradiyetha kunye nomzimba wakho.
Iincwadana zabasebenzisi zezixhobo zerediyo ezikhululwe kwilayisenisi ziya kuba nezi saziso zilandelayo okanye ezifanayo kwindawo ecacileyo kwincwadi yomsebenzisi okanye ngenye indlela kwisixhobo okanye zombini. Esi sixhobo sithobela i(s) umgangatho we-RSS we-Industry Canada-exemppt.
Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo sisenokungabangeli ukuphazamiseka
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko, kuquka uphazamiseko olunokubangela ukusebenza okungafunekiyo kwesixhobo.
Isilumkiso se-IC SAR:
IsiXhosa Esi sixhobo kufuneka sifakwe kwaye sisebenze kumgama ophakathi kwama-20 cm phakathi kweradiyetha kunye nomzimba wakho.
Kubalulekile: Ubushushu bokusebenza kwe-EUT abunakugqitha kuma-85 ℃ kwaye akufunekanga bube ngaphantsi kwe -40 ℃.
Ngale ndlela, i-Arduino Srl ibhengeza ukuba le mveliso iyahambelana neemfuno ezibalulekileyo kunye namanye amalungiselelo afanelekileyo oMgaqo ka-2014/53/EU. Le mveliso ivumelekile ukuba isetyenziswe kuwo onke amazwe angamalungu e-EU.
Ulwazi lweNkampani
| Igama leKhampani | Arduino SRL |
| Idilesi yeNkampani | Via Andrea Appiani, 25 – 20900 MONZA Italy) |
Amaxwebhu ekubhekiswa kuwo
| Ref | Ikhonkco |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (Cloud) | https://create.arduino.cc/editor |
| Cloud IDE Ukuqalisa | https://docs.arduino.cc/cloud/web-editor/tutorials/getting-started/getting-started-web- editor |
| I-Hub yeProjekthi | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Isalathiso seThala leeNcwadi | https://github.com/arduino-libraries/ |
| Ivenkile ye-Intanethi | https://store.arduino.cc/ |
Guqula iLog
| Umhla | Uhlaziyo | Iinguqu |
| 08/06/2023 | 1 | Ukukhutshwa kokuqala |
Arduino® UNO R4 WiFi Modified: 26/06/2023
Amaxwebhu / Izibonelelo
 |
I-ARDUINO ABX00087 UNO R4 WiFi [pdf] Isikhokelo somsebenzisi ABX00087 UNO R4 WiFi, ABX00087, UNO R4 WiFi, R4 WiFi, WiFi |
 |
Arduino ABX00087 UNO R4 WiFi [pdf] Incwadi yokusebenzisa ABX00087 UNO R4 WiFi, ABX00087, UNO R4 WiFi, R4 WiFi, WiFi |