ARDUINO ABX00087 UNO R4 WiFi
Tlhahisoleseding ya Sehlahiswa
SKU Reference Manual: EA-00087-ABX
Tlhaloso: Libaka tse reriloeng: Moetsi, ea qalang, thuto
Likaroloana:
- R7FA4M1AB3CFM#AA0, eo hangata e bitsoang RA4M1 databaseng sena, ke MCU ea mantlha ho UNO R4 WiFi, e hokahaneng le lihlooho tsohle tsa phini botong hammoho le libese tsohle tsa puisano.
- Memori: 256 kB Flash Memory, 32 kB SRAM, 8 kB Data Memory (EEPROM)
- Pheripherals: Capacitive Touch Sensing Unit (CTSU), USB 2.0 Full-Speed Module (USBFS), 14-bit ADC, Ho fihla ho 12-bit DAC,Ea sebetsa. Ampsekepe (OPAMP)
- Puisano: 1x UART (pin D0, D1), 1x SPI (pin D10-D13, hlooho ea ICSP), 1x I2C (pin A4, A5, SDA, SCL), 1x CAN (pin D4, D5, transceiver ea ka ntle ea hlokahala)
Bakeng sa lintlha tse ling tsa tekheniki mabapi le R7FA4M1AB3CFM#AA0 microcontroller, etela R7FA4M1AB3CFM#AA0 datasheet.
Lintlha tsa ESP32-S3-MINI-1-N8:
- Mojule ona o sebetsa joalo ka MCU ea bobeli ho UNO R4 WiFi mme o buisana le RA4M1 MCU o sebelisa mofetoleli oa boemo ba kelello.
- Hlokomela hore mojule ona o sebetsa ka 3.3 V ho fapana le RA4M1's 5 V e sebetsang ka matla.tage.
Bakeng sa lintlha tse ling tsa tekheniki mabapi le mojule oa ESP32-S3-MINI-1-N8, etela Lethathamo la lintlha tsa ESP32-S3-MINI-1-N8.
Litaelo tsa Tšebeliso ea Sehlahisoa
Maemo a Ts'ebetso a khothalelitsoeng:
| Letšoao | Tlhaloso | Min | Tlanya | Max |
|---|---|---|---|---|
| VIN | Keletso voltage tsoa ho VIN pad / DC Jack | 6 | 7.0 | 24 |
| VUSB | Keletso voltage ho tsoa ho sehokelo sa USB | 4.8 | 5.0 | 5.5 |
| HLOMPHO | Mocheso oa ho sebetsa | -40 | 25 | 85 |
E sebetsa hapeview:
Karolo ea ts'ebetsotage bakeng sa RA4M1 e tsitsitse ho 5 V hore e be hardware e lumellanang le lithebe, lisebelisoa, le lipotoloho tse thehiloeng ho liboto tse fetileng tsa Arduino UNO.
Boto Topology:
Pele View:
Ref. U1 U2 U3 U4 U5 U6 U_LEDMATRIX M1 PB1 JANALOG JDIGITAL JOFF J1 J2 J3 J5 J6 DL1
Holimo View:
Ref. DL2 LED RX (serial receive), DL3 LED Power (tala), DL4 LED SCK (serial clock), D1 PMEG6020AELRX Schottky Diode, D2 PMEG6020AELRX Schottky Diode, D3 PRTR5V0U2X,215 ESD Tšireletso
Sehlooho sa ESP:
Sehlooho se haufi le konopo ea RESET se ka sebelisoa ho fihlella mojule oa ESP32-S3 ka kotloloho. Li-pin tse fumanehang ke:
- ESP_IO42 – MMS debugging (Pin 1)
- ESP_IO41 - MTDI debugging (Pin 2)
- ESP_TXD0 – Serial Transmit (UART) (Pin 3)
- ESP_DOWNLOAD – boot (Pin 4)
- ESP_RXD0 – Serial Receive (UART) (Pin 5)
- GND - fatše (Pin 6)
Tlhaloso
Arduino® UNO R4 WiFi ke boto ea pele ea UNO e nang le microcontroller ea 32-bit le module ea ESP32-S3 Wi-Fi® (ESP32-S3-MINI-1-N8). E na le microcontroller ea RA4M1 e tsoang ho Renesas (R7FA4M1AB3CFM#AA0), e thehiloeng ho 48 MHz Arm® Cortex®-M4 microprocessor. Mohopolo oa UNO R4 WiFi o moholo ho feta ba pele ho oona, ka 256 kB flash, 32 kB SRAM le 8 kB ea EEPROM.
Karolo ea ts'ebetso ea RA4M1tage e tsitsitseng ho 5 V, athe module ea ESP32-S3 ke 3.3 V. Puisano pakeng tsa li-MCU tsena tse peli e etsoa ka mofetoleli oa logic level (TXB0108DQSR).
Libaka tse reriloeng:
Moetsi, moqali, thuto
Likaroloana
R7FA4M1AB3CFM#AA0, eo hangata e bitsoang RA4M1 databaseng sena, ke MCU ea mantlha ho UNO R4 WiFi, e hokahaneng le lihlooho tsohle tsa phini botong hammoho le libese tsohle tsa puisano.
Fetileview
- 48 MHz Arm® Cortex®-M4 microprocessor e nang le karolo e phaphametseng (FPU) 5 V e sebetsangtage
- Nako ea 'Nete (RTC)
- Setsi sa Tšireletso ea Memori (MPU)
- Sefetoleli sa Digital-to-analog (DAC)
Mohopolo
- 256 kB Flash Memori
- 32 kB SRAM
- 8 kB Memori ea Boitsebiso (EEPROM)
Pheripherals
- Capacitive Touch Sensing Unit (CTSU)
- USB 2.0 Full-Speed Module (USBFS)
- 14-bit ADC
- Ho fihlela ho 12-bit DAC
- Ts'ebetso Ampsekoahelo (OPAMP)
Matla
- Tshebetso voltage bakeng sa RA4M1 ke 5 V
- Recommended input voltage (VIN) ke 6-24 V
- Jack ea moqomo e hokahantsoeng le phini ea VIN (6-24 V)
- Matla ka USB-C® ho 5 V
Puisano
- 1x UART (pin D0, D1)
- 1x SPI (pin D10-D13, hlooho ea ICSP)
- 1x I2C (pin A4, A5, SDA, SCL)
- 1x CAN (pin D4, D5, transceiver ea kantle ea hlokahala)
Sheba lethathamo la lintlha tse felletseng tsa R7FA4M1AB3CFM#AA0 sehokelong se ka tlase:
- R7FA4M1AB3CFM#AA0 datasheet
ESP32-S3-MINI-1-N8 ke MCU ea bobeli e nang le antenna e hahelletsoeng ka har'a khokahanyo ea Wi-Fi® & Bluetooth®. Mojule ona o sebetsa ho 3.3 V mme o buisana le RA4M1 o sebelisa mofetoleli oa boemo ba logic (TXB0108DQSR).
Fetileview
- Xtensa® dual-core 32-bit LX7 microprocessor
- 3.3 V ea ho sebetsa voltage
- 40 MHz kristale oscillator
WiFi®
- Tšehetso ea Wi-Fi® e nang le 802.11 b/g/n standard (Wi-Fi® 4)
- Sekhahla sa Bit ho fihla ho 150 Mbps
- 2.4 GHz sehlopha
Bluetooth®
- Bluetooth® 5
Sheba datha e felletseng ea ESP32-S3-MINI-1-N8 sehokelong se ka tlase:
- Lethathamo la lintlha tsa ESP32-S3-MINI-1-N8
Boto
Kopo Examples
UNO R4 WiFi ke karolo ea letoto la pele la UNO la liboto tsa ntlafatso tsa 32-bit, tse neng li thehiloe pele ho li-microcontrollers tsa 8-bit AVR. Ho na le likete tsa litataiso, lithupelo le libuka tse ngotsoeng ka boto ea UNO, moo UNO R4 WiFi e ntšetsang pele lefa la eona.
Boto e na le likou tse 14 tsa dijithale tsa I/O, liteishene tse 6 tsa analoge, lithakhisa tse inehetseng bakeng sa likhokahano tsa I2C, SPI le UART. E na le memori e kholoanyane haholo: memori ea flash makhetlo a 8 (256 kB) le makhetlo a 16 ho feta SRAM (32 kB). Ka lebelo la oache ea 48 MHz, e boetse e potlakile ka 3x ho feta ba pele ho eona.
Ntle le moo, e na le mojule oa ESP32-S3 bakeng sa khokahano ea Wi-Fi® & Bluetooth®, hammoho le matrix a LED a 12 × 8, e etsang e 'ngoe ea boto e ikhethang ea Arduino ho fihlela joale. Matrix ea LED e hlophisehile ka botlalo, moo o ka kenyang eng kapa eng ho tloha ho liforeimi tse ntseng li le teng ho ea ho lipopae tsa tloaelo.
Merero ea boemo ba ho kena: Haeba ona e le projeke ea hau ea pele ka har'a likhoutu le lisebelisoa tsa elektroniki, UNO R4 WiFi e nepahetse. Ho bonolo ho qala ka eona, 'me e na le litokomane tse ngata tsa inthanete.
Lisebelisoa tse bonolo tsa IoT: aha merero ntle le ho ngola khoutu efe kapa efe ea marang-rang ho Arduino IoT Cloud. Lekola boto ea hau, e hokahane le liboto le lits'ebeletso tse ling, 'me u ntlafatse merero e metle ea IoT.
Matrix a LED: 12 × 8 LED matrix boto e ka sebelisoa bakeng sa ho bonts'a li-animation, ho bala mongolo, ho etsa lipapali tsa mini-lipapali le tse ling tse ngata, e le tšobotsi e phethahetseng ho fa projeke ea hau botho bo bongata.
Lihlahisoa tse Amanang
- UNO R3
- UNO R3 SMD
- UNO R4 Minima
Lintlha
Maemo a Tšebetso a khothalelitsoeng
| Letšoao | Tlhaloso | Min | Tlanya | Max | Yuniti |
| VIN | Keletso voltage tsoa ho VIN pad / DC Jack | 6 | 7.0 | 24 | V |
| VUSB | Keletso voltage ho tsoa ho sehokelo sa USB | 4.8 | 5.0 | 5.5 | V |
| HLOMPHO | Mocheso oa ho sebetsa | -40 | 25 | 85 | °C |
Hlokomela: VDD e laola boemo ba logic mme e hokahane le seporo sa matla sa 5V. VAREF ke ea analog logic.
E sebetsa hapeview
Setšoantšo se Thibeloang
Board Topology
Pele View
| Ref. | Tlhaloso |
| U1 | R7FA4M1AB3CFM#AA0 Microcontroller IC |
| U2 | Tlhaloso: NLASB3157DFT2G Multiplexer |
| U3 | ISL854102FRZ-T Buck Converter |
| U4 | TXB0108DQSR mofetoleli oa boemo ba kelello (5 V – 3.3 V) |
| U5 | SGM2205-3.3XKC3G/TR 3.3 V linear regulator |
| U6 | Tlhaloso: NLASB3157DFT2G Multiplexer |
| U_LEDMATRIX | 12 × 8 LED Red Matrix |
| M1 | ESP32-S3-MINI-1-N8 |
| PB1 | TSOHLE Konopo |
| JANALOGE | Lihlooho tsa li-analog/output |
| JDIGITAL | Digital input/output headers |
| JOFF | TLOA, sehlooho sa VRTC |
| J1 | CX90B-16P sehokelo sa USB-C® |
| J2 | SM04B-SRSS-TB(LF)(SN) I2C sehokelo |
| J3 | Sehlooho sa ICSP (SPI) |
| J5 | DC Jack |
| J6 | Sehlooho sa ESP |
| DL1 | LED TX (serial transmit) |
| DL2 | LED RX (serial amohela) |
| DL3 | Matla a LED (botala) |
| DL4 | LED SCK (serial oache) |
| D1 | Tlhaloso: PMEG6020AELRX Schottky Diode |
| D2 | Tlhaloso: PMEG6020AELRX Schottky Diode |
| D3 | PRTR5V0U2X,215 Tšireletso ea ESD |
Microcontroller (R7FA4M1AB3CFM#AA0)
UNO R4 WiFi e ipapisitse le 32-bit RA4M1 series microcontroller, R7FA4M1AB3CFM#AA0, ho tsoa Renesas, e sebelisang microprocessor ea 48 MHz Arm® Cortex®-M4 e nang le yuniti ea lintlha tse phaphametseng (FPU).
Karolo ea ts'ebetsotage bakeng sa RA4M1 e behiloe ho 5 V hore e be hardware e lumellanang le lithebe, lisebelisoa le li-circuits tse thehiloeng ho liboto tse fetileng tsa Arduino UNO.
The R7FA4M1AB3CFM#AA0 features:
- 256 kB sh / 32 kB SRAM / 8 kB foleshe ea data (EEPROM)
- Nako ea 'Nete (RTC)
- 4x Direct Memory Access Controller (DMAC)
- 14-bit ADC
- Ho fihlela ho 12-bit DAC
- OPAMP
- CAN bese
Bakeng sa lintlha tse ling tsa tekheniki mabapi le microcontroller ena, etela lethathamo la litokomane tsa semmuso tsa Renesas - RA4M1.
6 Wi-Fi® / Bluetooth® Mojule (ESP32-S3-MINI-1-N8)
Mojule oa Wi-Fi® / Bluetooth® LE ho UNO R4 WiFi o tsoa ho ESP32-S3 SoCs. E na le Xtensa® dual-core 32-bit LX7 MCU, e leng antenna e hahelletsoeng ka hare le tšehetso bakeng sa lihlopha tsa 2.4 GHz.
Lintlha tsa ESP32-S3-MINI-1-N8:
- Wi-Fi® 4 – 2.4 GHz sehlopha
- Bluetooth® 5 LE tšehetso
- 3.3 V ea ho sebetsa voltagE 384 kB ROM
- 512 kB SRAM
- Ho fihla ho 150 Mbps bit rate
Mojule ona o sebetsa joalo ka MCU ea bobeli ho UNO R4 WiFi, 'me o buisana le RA4M1 MCU o sebelisa mofetoleli oa boemo ba kelello. Hlokomela hore mojule ona o sebetsa ka 3.3 V ho fapana le RA4M1's 5 V e sebetsang ka matla.tage.
Sehlooho sa ESP
Sehlooho se haufi le konopo ea RESET se ka sebelisoa ho fihlella mojule oa ESP32-S3 ka kotloloho. Li-pin tse fumanehang ke:
- ESP_IO42 – MMS debugging (Pin 1)
- ESP_IO41 - MTDI debugging (Pin 2)
- ESP_TXD0 – Serial Transmit (UART) (Pin 3)
- ESP_DOWNLOAD – boot (Pin 4)
- ESP_RXD0 – Serial Receive (UART) (Pin 5)
- GND - fatše (Pin 6)
USB Bridge
Ha o etsa lenaneo la UNO R4 WiFi, RA4M1 MCU e hlophisoa ka mojule oa ESP32-S3 ka mokhoa oa kamehla. Li-switch tsa U2 le U6 li ka fetola puisano ea USB ho ea ka ho toba ho RA4M1 MCU, ka ho ngola boemo bo phahameng ho P408 pin (D40).
Ho kopanya lipampiri tsa SJ1 hammoho ho beha puisano ea USB ka kotloloho ho RA4M1, ho feta ESP32-S3.
Sehokedi sa USB
UNO R4 WiFi e na le kou e le 'ngoe ea USB-C®, e sebelisetsoang ho matlafatsa le ho hlophisa boto ea hau hammoho le ho romella le ho amohela puisano ea serial.
Tlhokomeliso: Boto ha ea lokela ho tsamaisoa ka matla a fetang 5 V ka boema-kepe ba USB-C®.
LED Matrix
UNO R4 WiFi e na le matrix a 12 × 8 a li-LED tse khubelu (U_LEDMATRIX), tse hokahaneng ho sebelisoa mokhoa o tsejoang ka hore ke charlieplexing.
Lithakhisa tse latelang ho RA4M1 MCU li sebelisoa bakeng sa matrix:
- P003
- P004
- P011
- P012
- P013
- P015
- P204
- P205
- P206
- P212
- P213
Li-LED tsena li ka finyelloa e le sehlopha, ho sebelisoa laebrari e itseng. Sheba 'mapa o ka tlase:
Matrix ena e ka sebelisoa bakeng sa merero e mengata le merero ea prototyping, 'me e ts'ehetsa lipopae, meralo e bonolo ea papali le mongolo oa ho phenya har'a lintho tse ling.
Sefetoleli sa Digital Analog (DAC)
UNO R4 WiFi e na le DAC e nang le qeto e fihlang ho 12-bit e hokeletsoeng ho pin ea analog ea A0. DAC e sebelisoa ho fetolela lets'oao la dijithale ho lets'oao la analog.
DAC e ka sebelisoa bakeng sa tlhahiso ea mats'oao bakeng sa mohlala, lits'ebetso tsa audio, joalo ka ho hlahisa le ho fetola maqhubu a sawtooth.
Sehokelo sa I2C
Sehokelo sa I2C SM04B-SRSS-TB(LF)(SN) se hoketsoe ho bese ea bobeli ea I2C botong. Hlokomela hore sehokelo sena se tsamaisoa ka 3.3 V.
Sehokelo sena se boetse se arolelana likhokahano tse latelang tsa phini:
JANALOG sehlooho
- A4
- A5
JDIGITAL hlooho
- SDA
- SCL
Hlokomela: kaha A4/A5 e hokahane le bese e kholo ea I2C, tsena ha lia lokela ho sebelisoa e le lisebelisoa tsa ADC neng kapa neng ha bese e sebelisoa. Leha ho le joalo, o ka hokela lisebelisoa tsa I2C ho e 'ngoe le e 'ngoe ea likhokahano tsena ka nako e le ngoe.
Likhetho tsa Matla
Matla a ka fanoa ka phini ea VIN, kapa ka sehokelo sa USB-C®. Haeba matla a fanoa ka VIN, ISL854102FRZ buck converter e nka vol.tagho fihlela ho 5 V.
Ka bobeli lithakhisa tsa VUSB le VIN li hokahantsoe le converter ea buck ea ISL854102FRZ, e nang le li-diode tsa Schottky sebakeng sa polarity le ho feta.tage tshireletso ka ho latellana.
Matla ka lisebelisoa tsa USB hoo e ka bang ~ 4.7 V (ka lebaka la ho theoha ha Schottky) ho ea ho RA4M1 MCU.
Molaoli oa linear (SGM2205-3.3XKC3G/TR) o fetola 5 V ho tloha ho converter ea buck kapa USB, 'me o fana ka 3.3 V ho likarolo tse' maloa, ho kenyelletsa le module ea ESP32-S3.
Sefate sa Matla
Pin Moqtage
The general operation voltage bakeng sa UNO R4 WiFi ke 5 V, leha ho le joalo mojule oa ESP32-S3 o sebetsa voltagke 3.3V.
Hlokomela: Ho bohlokoa haholo hore lithakhisa tsa ESP32-S3 (3.3 V) li se ke tsa kopana le leha e le efe ea lithakhisa tsa RA4M1 (5 V), kaha sena se ka senya lipotoloho.
Pina Hona Joale
Li-GPIO tse ho R7FA4M1AB3CFM#AA0 microcontroller li ka sebetsana ka mokhoa o sireletsehileng ho fihla ho 8 mA ea hona joale. Le ka mohla u se ke ua hokela lisebelisoa tse hulang matla a holimo ka kotloloho ho GPIO kaha sena se ka senya potoloho.
Bakeng sa ho matlafatsa mohlala li-motor tsa servo, kamehla sebelisa matla a kantle.
Boitsebiso ba Mechini
Pinout
Analoge
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | TLHOKOMELO | NC | Ha e Kopanetsoe |
| 2 | IOREF | IOREF | Reference for digital logic V - e hokahaneng le 5 V |
| 3 | Seta bocha | Seta bocha | Seta bocha |
| 4 | +3V3 | Matla | +3V3 Seporo sa Matla |
| 5 | +5V | Matla | +5V Seporo sa Matla |
| 6 | GND | Matla | Fatše |
| 7 | GND | Matla | Fatše |
| 8 | VIN | Matla | MoqtagKeletso |
| 9 | A0 | Analoge | Kenyelletso ea analog 0 / DAC |
| 10 | A1 | Analoge | Kenyelletso ea analog 1 / OPAMP+ |
| 11 | A2 | Analoge | Kenyelletso ea analog 2 / OPAMP- |
| 12 | A3 | Analoge | Kenyelletso ea analog 3 / OPAMPTsoa |
| 13 | A4 | Analoge | Kenyelletso ea Analog 4 / I2C Serial Data (SDA) |
| 14 | A5 | Analoge | Kenyelletso ea Analog 5 / I2C Serial Clock (SCL) |
Dijithale
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | SCL | Dijithale | I2C Serial Clock (SCL) |
| 2 | SDA | Dijithale | I2C Serial Datal (SDA) |
| 3 | AREF | Dijithale | Analog Reference Voltage |
| 4 | GND | Matla | Fatše |
| 5 | D13/SCK/CANRX0 | Dijithale | GPIO 13 / SPI Clock / CAN Receiver (RX) |
| 6 | D12/CIPO | Dijithale | GPIO 12 / SPI Controller In Peripheral Out |
| 7 | D11/COPI | Dijithale | GPIO 11 (PWM) / SPI Controller Out Peripheral In |
| 8 | D10/CS/CATX0 | Dijithale | GPIO 10 (PWM) / SPI Chip Select / CAN Transmitter (TX) |
| 9 | D9 | Dijithale | GPIO 9 (PWM~) |
| 10 | D8 | Dijithale | GPIO 8 |
| 11 | D7 | Dijithale | GPIO 7 |
| 12 | D6 | Dijithale | GPIO 6 (PWM~) |
| 13 | D5 | Dijithale | GPIO 5 (PWM~) |
| 14 | D4 | Dijithale | GPIO 4 |
| 15 | D3 | Dijithale | GPIO 3 (PWM~) |
| 16 | D2 | Dijithale | GPIO 2 |
| 17 | D1/TX0 | Dijithale | GPIO 1 / Serial 0 Transmitter (TX) |
| 18 | D0/TX0 | Dijithale | GPIO 0 / Serial 0 Receiver (RX) |
TLOA
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | TLOA | Matla | Bakeng sa ho laola phepelo ea motlakase |
| 2 | GND | Matla | Fatše |
| 1 | VRTC | Matla | Khokelo ea betri ho matla a RTC feela |
ICSP
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | CIPO | Ka hare | Controller In Peripheral Out |
| 2 | +5V | Ka hare | Matla a matla a 5V |
| 3 | TS'ELISO | Ka hare | Seriba oache |
| 4 | COPI | Ka hare | Controller Out Peripheral In |
| 5 | RETS'ELISITSOE | Ka hare | Seta bocha |
| 6 | GND | Ka hare | Fatše |
Ho Beha Likoti le Kemiso ea Boto
Ts'ebetso ea Boto
- Ho qala - IDE
Haeba u batla ho hlophisa UNO R4 WiFi ea hau ha u ntse u le sieo inthaneteng u hloka ho kenya Arduino® Desktop IDE [1]. Ho hokela UNO R4 WiFi komporong ea hau, o tla hloka thapo ea USB ea Type-C®, e ka fanang ka matla ho boto, joalo ka ha ho bonts'itsoe ke LED (DL1). - Ho qala - Arduino Web Mohlophisi
Liboto tsohle tsa Arduino, ho kenyeletsoa le ena, li sebetsa ka ntle ho lebokose ho Arduino® Web Mohlophisi [2], ka ho kenya plugin e bonolo feela.
Arduino Web Editor e tšoaroa inthaneteng, ka hona e tla lula e le morao-rao ka likarolo tsa morao-rao le tšehetso bakeng sa liboto tsohle. Latela [3] ho qala ho kenya likhoutu ho sebatli le ho kenya litšoantšo tsa hau botong ea hau. - Ho qala - Arduino IoT Cloud
Lihlahisoa tsohle tse nolofalitsoeng tsa Arduino IoT li tšehetsoa ho Arduino IoT Cloud e u lumellang hore u kene, u kenye le ho sekaseka lintlha tsa sensor, ho qala liketsahalo, le ho iketsetsa ntlo kapa khoebo ea hau. - Lisebelisoa tsa Marang-rang
Kaha joale u se u fetile linthong tsa motheo tsa seo u ka se etsang ka boto u ka hlahloba menyetla e sa feleng eo e fanang ka eona ka ho hlahloba merero e teng ho Arduino Project Hub [4], Arduino Library Reference [5], le lebenkele la marang-rang [6] ]; moo o tla khona ho tlatselletsa boto ea hau ka li-sensor, li-actuator le tse ling. - Boto ea Pholiso
Liboto tsohle tsa Arduino li na le bootloader e hahelletsoeng ka hare e lumellang ho bonesa boto ka USB. Haeba sketch e notlela processor mme boto ha e sa fumaneha ka USB, hoa khonahala ho kenya mokhoa oa bootloader ka ho tlanya konopo ea reset hang ka mor'a ho tima.
Setifikeiti
15 Phatlalatso ea Conformity CE DoC (EU)
Re phatlalatsa tlas'a boikarabelo ba rona hore lihlahisoa tse ka holimo li lumellana le litlhoko tsa bohlokoa tsa Litaelo tse latelang tsa EU, kahoo re tšoaneleha bakeng sa ho tsamaea ka bolokolohi ka har'a limmaraka tse kenyelletsang European Union.
Union (EU) le European Economic Area (EEA).
16 Phatlalatso ea Tumellano le EU RoHS & REACH 211 01/19/2021
Liboto tsa Arduino li lumellana le RoHS 2 Directive 2011/65/EU ea Paramente ea Europe le RoHS 3 Directive 2015/863/EU ea Lekhotla la 4 Phuptjane 2015 mabapi le thibelo ea tšebeliso ea lintho tse ling tse kotsi ho lisebelisoa tsa motlakase le tsa elektroniki.
| Ntho | Maximum Limit (ppm) |
| Lebisa (Pb) | 1000 |
| Cadmium (Cd) | 100 |
| Motsoako (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Litokoloho : Ha ho litokollo tse batloang.
Arduino Boards e lumellana ka botlalo le litlhoko tse amanang le European Union Regulation (EC) 1907 /2006 mabapi le Ngoliso, Tlhahlobo, Tumello le Thibelo ea Lik'hemik'hale (REACH). Ha re phatlalatse leha e le efe ea SVHCs (https://echa.europa.eu/web/moeti/lethathamo la moeti), Lethathamo la Bakhethoa ba Matšoenyeho a Phahameng ka ho Fetisisa bakeng sa tumello e lokollotsoeng hajoale ke ECHA, le teng lihlahisoa tsohle (le sephutheloana) ka bongata bo lekanang le mahloriso a lekanang kapa a ka holimo ho 0.1%. Ho latela tsebo ea rona, re boetse re phatlalatsa hore lihlahisoa tsa rona ha li na letho la lintho tse thathamisitsoeng ho "Authorization List" (Annex XIV ea melaoana ea REACH) le Substances of Very High Concern (SVHC) ka chelete efe kapa efe ea bohlokoa joalo ka ha ho boletsoe. ka Sehlomathiso sa XVII sa Lethathamo la Bakhethoa le hatisitsoeng ke ECHA (European Chemical Agency) 1907 /2006/EC.
Phatlalatso ea Liminerale tsa Khohlano
Joaloka mofani oa lefats'e oa likarolo tsa elektronike le motlakase, Arduino e tseba boitlamo ba rona mabapi le melao le melaoana e mabapi le Conflict Minerals, haholo-holo Dodd-Frank Wall Street Reform le Consumer Protection Act, Karolo ea 1502. Arduino ha e hlahise kapa ha e sebetsane le likhohlano ka ho toba. liminerale tse kang Tin, Tantalum, Tungsten, kapa Khauta. Liminerale tsa likhohlano li fumaneha lihlahisoa tsa rona ka mokhoa oa solder, kapa e le karolo ea li-alloys tsa tšepe. E le karolo ea boitelo ba rona bo loketseng, Arduino e ikopanye le bafani ba thepa ka har'a ketane ea rona ea phepelo ho netefatsa hore ba tsoela pele ho latela melaoana. Ho latela lintlha tse fumanoeng ho tla fihlela joale, re phatlalatsa hore lihlahisoa tsa rona li na le Liminerale tsa Likhohlano tse tsoang libakeng tse se nang likhohlano.
FCC Tlhokomeliso
Liphetoho life kapa life tse sa amoheloeng ka kotloloho ke mokha o ikarabellang bakeng sa tumellano li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.
Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.
Polelo ea Ts'oaetso ea Mahlaseli a FCC RF:
- Transmitter ena ha ea lokela ho ba sebakeng se le seng kapa ho sebetsa mmoho le antenna efe kapa efe kapa transmitter.
- Sesebelisoa sena se lumellana le meeli ea ho pepeseha ha mahlaseli a RF e behiloeng bakeng sa tikoloho e sa laoleheng.
- Sesebelisoa sena se lokela ho kengoa le ho sebetsoa ka bonyane ba 20 cm lipakeng tsa radiator le 'mele oa hau.
Libukana tsa mosebelisi bakeng sa lisebelisoa tsa seea-le-moea tse sa lumelloeng ke laesense li tla ba le tsebiso e latelang kapa e lekanang le eona sebakeng se hlakileng bukeng ea mosebelisi kapa ka mokhoa o mong sesebelisoa kapa ka bobeli. Sesebediswa sena se dumellana le ditekanyetso tsa laesense tsa Industry Canada tse sa kgetheng RSS.
Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- sesebelisoa sena se ka 'na sa se ke sa baka tšitiso
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.
Tlhokomeliso ea IC SAR:
Sesotho Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka sa bonyane 20 cm pakeng tsa radiator le 'mele oa hau.
Bohlokoa: Mocheso o sebetsang oa EUT ha oa lokela ho feta 85 ℃ mme ha oa lokela ho ba ka tlase ho -40 ℃.
Ka hona, Arduino Srl e phatlalatsa hore sehlahisoa sena se lumellana le litlhoko tsa bohlokoa le lipehelo tse ling tse amehang tsa Directive 2014/53/EU. Sehlahisoa sena se lumelletsoe ho sebelisoa linaheng tsohle tsa litho tsa EU.
Lintlha tsa Khampani
| Lebitso la K'hamphani | Arduino SRL |
| Aterese ea Khampani | Via Andrea Appiani, 25 - 20900 MONZA Italy) |
Litokomane Tsa Litšupiso
| Ref | Sehokelo |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (Leru) | https://create.arduino.cc/editor |
| Cloud IDE Ho qala | https://docs.arduino.cc/cloud/web-editor/tutorials/getting-started/getting-started-web- editor |
| Morero Hub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Reference Library | https://github.com/arduino-libraries/ |
| Online Store | https://store.arduino.cc/ |
Fetola Log
| Letsatsi | Khatiso | Liphetoho |
| 08/06/2023 | 1 | Phatlalatso ea Pele |
Arduino® UNO R4 WiFi e Fetotsoe: 26/06/2023
Litokomane / Lisebelisoa
 |
ARDUINO ABX00087 UNO R4 WiFi [pdf] Bukana ea Mosebelisi ABX00087 UNO R4 WiFi, ABX00087, UNO R4 WiFi, R4 WiFi, WiFi |
 |
Arduino ABX00087 UNO R4 WiFi [pdf] Bukana ea Mosebelisi ABX00087 UNO R4 WiFi, ABX00087, UNO R4 WiFi, R4 WiFi, WiFi |