HONGWEI MICROELECTRONICS ESP32 C3 Development Board Modules Mini Wifi BT Bluetooth Module User Guide

ESP32 C3 Development Board Modules Mini Wifi BT Bluetooth Module

“

ข้อมูลสินค้า

ข้อมูลจำเพาะ:

• Product: ESP32 Development Board
• Manufacturer: Espressif
• Compatibility: Arduino IDE
• Webเว็บไซต์: https://www.arduino.cc/en/Main/Software

คำแนะนำการใช้ผลิตภัณฑ์:

1. Download Software and Development Board:

1. Download the Arduino IDE software from the official webเว็บไซต์
   ข้างต้น
2. Open the Arduino IDE software to start the setup process.

2. Add ESP32 Development Environment:

1. In Arduino IDE, go to File -> Preferences (shortcut key
   ‘Ctrl+,’).
2. Add the JSON address of the ESP32 development board in the
   board manager settings.
3. Click ‘OK’ to confirm and return to the Arduino IDE
   หน้าแรก
4. In the Development Board Manager, search for ESP32 and install
   สภาพแวดล้อมการพัฒนา

3. Start Downloading and Testing:

1. เลือก File -> อดีตample -> Blink to download a flashing
   light program for testing.
2. Modify the code as needed, such as changing LED_PIN to the
   desired pin number.
3. Select the corresponding port and development board model in
   Arduino IDE.
4. If the Com port is not recognized, manually enter download mode
   following the provided methods.
5. Click upload and wait for the download to complete. The blue
   indicator light on the module should flash normally.

คำถามที่พบบ่อย (FAQ) :

Q: How do I troubleshoot if the blue indicator light does not
flash after uploading?

A: Check the connection between the development board and your
computer, ensure the correct port and board are selected in Arduino
IDE, and try re-uploading the program.

Q: Can I use other development environments with this ESP32
กระดาน?

A: While these instructions are tailored for Arduino IDE, you
may be able to adapt them for other environments that support ESP32
การพัฒนา.

-

-
คำแนะนำ:
1. Download software and development board
2. We use modules in Arduino IDE (which can be downloaded from the official website) https://www.arduino.cc/en/Main/Software Using the development environment as an ex
ample to illustrate the usage of modules. Open the Arduino IDE software and the following interface will appear
2.Add ESP32 development environment
ESP32 development environment add path In Arduino IDE, open File ->Preferences (shortcut key ‘Ctrl+,’). support https://dl.espressif.com/dl/package_esp32_index.json Put the JSON address of this development board into the attachment In the website of the development board manager. Click ‘OK’ (the new version is’ OK ‘). Click ‘OK’ again (the new version is’ OK ‘) to return to the Arduino IDE homepage.

-
Click on the Development Board Manager, the Development Board Manager window appears, search for ESP32, and install the development environment

-
Installed ones can be used directly. After the uninstalled installation, it can be seen in the development board that a lot of support for ESP32 modules has been added.
3.Start downloading the flashing light program for testing: Select File - อดีตample – BLink
As shown in the figure below, change LED_SULLTIN to 8

-
Select the corresponding port and development board model Note: If the Com port cannot be recognized on Arduino, you can try the following method: Manually enter download mode: Method 1: Press and hold BOOT to power on. Method 2: Hold down the BOOT button on ESP32C3, then press the RESET button, release the RESET button, and then release the BOOT button. At this point, ESP32C3 will enter download mode.
Click upload, wait for the download to complete, and the blue indicator light on the module will flash normally

เอกสาร / แหล่งข้อมูล

HONGWEI MICROELECTRONICS ESP32 C3 Development Board Modules Mini Wifi BT Bluetooth Module [พีดีเอฟ] คู่มือการใช้งาน ESP32 C3 Development Board Modules Mini Wifi BT Bluetooth Module, ESP32 C3, Development Board Modules Mini Wifi BT Bluetooth Module, Board Modules Mini Wifi BT Bluetooth Module, Wifi BT Bluetooth Module, BT Bluetooth Module, Bluetooth Module

อ้างอิง

• คู่มือการใช้งาน