WM SYSTEMS WM-E LCB IoT Load Control Chinja

INTERFACES

• Simba rekupa - AC simba rekuisa, 2-pini terminal block
• Relay 1..2 - latching relay, 16A 250V AC, chinja modes: NO, NC, COM, terminal block
• Relay 3..4 - latching relay, 16A 250V AC, switch mode: NC, COM, terminal block
• RJ45 connector features:
  • Ethernet - 10/100MBit, RJ45 chiteshi, neUTP Cat5 tambo
  • RS485 - yezvishandiso zvekunze netambo yakaitwa neY
  • P1 interface - yemamita akangwara neY-yakaita tambo
• LED1..LED4/WAN – Status LEDs
• SIM - Push isa SIM kadhi slot (mini SIM, mhando 2FF) micro-SD kadhi slot - yememory makadhi (max. 32 GByte)
• Yemukati LTE Antenna - inonamira, inotakurika pamusoro

ZVINO & ZVOKUDYA / KUSHANDA ZVINHU

• Simba rekuisa: ~100-240V AC, +10% / -10%, 50-60Hz +/- 5%
• Kushandisa: Zvishoma: 3W / Avhareji: 5W / Max: 9W (0.25A)
• Serura module sarudzo:
  • LTE Cat.1: Telit LE910C1-EUX (LTE Cat.1: B1, B3, B7, B8, B20, B28A / 3G: B1, B3, B8 / 2G: B3, B8)
  • LTE Cat.M / Cat.NB: Telit ME910C1-E1 (LTE M1 & NB1 B3, B8, B20)
• Kushanda / kuchengetedza tembiricha: pakati -40'C uye +85'C, 0-95% rel. mwando
• Saizi: 175 x 104 x 60 mm / Kurema: 420gr
• Enclosure: IP52 ABS plastiki ine transparent terminal chivharo, inogona kuisirwa njanji / kumadziro

  

SCHEMATIC FIGURE OF INTERFACES, PINOUT

KUCHENJERA! USA KUBATISA ~ 100-240V AC POWER SOURCE kune pigtail AC CONNECTOR (24) KANA KUPIWA KWESIMBA (12) YEDIVISI kusvikira usati wapedza newaya!
KANA AKAZARURWA ZVINHU, GARA IONA KUTI PCB HAINA KUSANGANISWA NESIMBA SOURCE uye ma supercapacitors apera (LED SIGNALS ARE INACTIVE) Usati Wabata PCB!

INSTALLATION MATANHO

1. Bvisa purasitiki, inoonekera chepamusoro chevhavha chevhavha (1) nekuburitsa sikuruu (3) kubva pamusoro peyakavharirwa.
2. Svetera kumusoro chikamu chepurasitiki (1) nekungwarira pazasi pechigadziko (2), wobva wabvisa chivharo chepamusoro (1).
3. Iye zvino unogona kusununguka kubatanidza waya uye tambo kune madoko uye nzvimbo dzekupindirana. Nyatsovhura hoko dzepurasitiki (12) dzegadziko yakavharirwa (2) nescrewdriver.
4. Iye zvino chigadziko chepurasitiki chinogona kuonekwa nePCB yakaungana (4) mukati. Vhura PCB (4) uye bvisa kubva pachigadziko (2), wozotendeutsa PCB pasi. Iye zvino unogona kuona pazasi pePCB.
5. Isa mini SIM kadhi (yakagadzirwa neAPN) mune iyo SIM inobata (23). Tarisa mufananidzo uri papeji rinotevera: iyo SIM yakachekwa mupendero inofanirwa kutariswa kuPCB uye iyo SIM chip inotarisa pasi. Pinza uye sunda iyo SIM kusvika yasungwa (iwe unonzwa watinya ruzha).
6. Unogona kushandisa micro-SD kadhi kana uchida (optional). Wobva waisa memori kadhi mune mini-SD kadhi slot (22) uye sunda kusvika yasungwa zvakachengeteka.
7. Zvino dzosera PCB uye dzosera kumashure kweyakavharirwa base (2).
8. Tarisa paPCB kuti LTE antenna tambo (16) yakabatana neAntenna RF yekubatanidza (15).
9. Isa kumashure iyo inobviswa chena ABS epurasitiki chikamu chepamusoro kune hwaro (2) - tarisa kuti zvikorekedzo (12) zviri kuvhara.
10. Ita wiring maererano nezvinodiwa - zvichibva pane schematic figure (pamusoro).
11. Batanidza AC power chord (AC pigtailed connector) waya (24) kumapini maviri ekutanga (5) emudziyo (kubva kuruboshwe kuenda kurudyi): dema kusvika N (neutric), tsvuku kusvika L (mutsara).
12. Unganidza tambo yekuvhenekesa relay waya (25) yemugwagwa wemwenje kabati bhokisi - kune inodiwa relay kubuda (6).
    Ziva kuti RELAY 1..2 iri latching relays, iyo inobvumira iyo NO, NC, COM yekubatanidza uye switching modes, nepo RELAY 3..4 ine chete NC, COM yekubatanidza uye switching mode.
13. Batanidza iyo Y-yakaita UTP tambo (27) - yeEthernet / RS485 / P1 - kana yakananga UTP tambo (26) - yeEthernet chete - kune RJ45 port (7) - zvinoenderana nezvinodiwa. Rimwe divi reEthernet tambo rinofanira kunge rakabatana nePC yako kana mudziyo wekunze waunoda kubatanidza.
    Ziva, kuti RS485 / P1 interface waya dzakamira dzakamira sleeve dzinozunguza waya (28).

    

14. Batanidza iyo RS485 kune yekunze mudziyo. Iyo P1 interface inowanikwa yekubatanidza magetsi mita / smart metering modem.
15. Dzosera chivharo chepamusoro chepurasitiki chinoonekera (1) kusvika pagadziko (2).
16. Iyo mudziyo yakavharirwa ine maviri-mhando yekumisikidza, iyo inofanirwa kukwirisa njanji kana kushandisa 3-point fixation nema screws, kana kushandisa chirauro (munzvimbo yakarembera kumadziro / mumugwagwa mwenje kabati bhokisi).
17. Batanidza iyo 100-240V AC magetsi kune pigtail yekubatanidza AC tambo yemagetsi (24) uye kune ekunze magetsi sosi / magetsi plug.
18. Chigadzirwa chacho chine pre-installed system. Mamiriro azvino echigadzirwa anoratidzwa nemwenje wayo we LED (11).
    • Mwenje ye LED - Tarisa Kuisa bhuku kuti uwane rumwe ruzivo.
    • REL.1: Relay#1 (modhi: NO, NC, COM) SET/RESET iripo
    • REL.2: Relay#2 (modhi: NO, NC, COM) SET/RESET iripo
    • REL.3: Relay#3 (modhi: NC, COM) hapana RESET pini, SET yakarambwa
    • REL.4: Relay#4 (modhi: NC, COM) hapana RESET pini, SET yakarambwa
    • WAN LED: yekubatanidza network (LAN/WAN chiitiko)
      Ziva, kuti chishandiso chine supercapacitor chikamu mukati, chinopa kuvharika kwakachengeteka kana paine simba outage. In case of a power utage - nekuda kweiyo supercapacitors - ine simba rakakwana rekupa kuchengetedzwa kwakachengeteka uye kuvharwa (pamberi peiyo supercapacitors ichave yapera).
      Iyo supercapacitor inogona kupera simba mushure meoutage kana kana iwe ukachengeta mudziyo kwemwedzi usina kubatanidza simba. Inofanirwa kuchajwa isati yashandiswa

      

KUTANGA CHINA

1. Paunenge uchiisa simba pachishandiso, iyo recharge ye supercapacitor inotangwa otomatiki. Iyo sisitimu yemudziyo inotangwa chete mushure mekupera kwekuchaja maitiro.
2. Batanidza Ethernet (UTP) tambo pakati pechishandiso cheRJ45 interface kana Y-yakaita tambo adapta uye PC yako Ethernet port. (Iyo RS485 mudziyo unofanirwa kuve wakabatana kune imwe Y-yakaita tambo yeimwe chiteshi.)
3. Rongedza iyo Ethernet interface's paPC yako yeTCP/IPv4 protocol yekuseta IP kero: 192.168.127.100 uye subnet mask: 255.255.255.0
4. Tanga chishandiso nekuwedzera iyo AC simba kune yekuisa magetsi (5).
5. Ese mana ma LED anozove asina chinhu kwemasekondi mashoma - zvakajairika. (Kana mudziyo wanga usingashandiswe kubva kwenguva yakareba, ma supercapacitors anofanirwa kubhadhariswa iyo microcontroller isati yatanga mudziyo.)
6. Mushure memasekonzi mashoma chete iyo WAN LED ichange ichivhenekerwa nekutsvuka kusvika iyo supercapacitor ichachajwa (mudziyo hausati watanga). Zvinogona kutora anenge 1-4 maminitsi.
7. Kana kuchaja kwapera, mudziyo uchatangwa. Ichasayirwa nekuvhenekera mutsvuku kwevose relay LEDs (REL.1..4) kwemasekonzi matatu uye neWAN LED iyo inovhenekera negirini munguva pfupi. Izvi zvinoreva kuti mudziyo wakatangwa.
8. Nenguva isipi, iyo WAN LED ichange isina chinhu uye ese ma LED relay (REL.1..4) acharamba achivhenekerwa nekutsvuka *, zvinoreva kuti mudziyo uri kuputika. Zvinotora anenge 1-2 maminetsi.*Yeuka, kana watobatanidza relay, izvo zvinosaina mamiriro ezvino relay nechimiro chayo chekurudyi (dzvuku zvinoreva switched OFF, green means switched ON).
9. Pakupera kweiyo boot process mudziyo unogona kusvikwa pane yayo network network (LAN neWAN) kana yakange yatogadzirwa. Kana ikozvino network interface iripo, inosainwa neWAN LED chiratidzo.
10. Kana mudziyo uchinge wasvika pane yakagadziriswa LAN interface, iyo WAN LED ichange ichivheneka nguva nenguva negirinhi. (Kana iri kupenya nekukurumidza, inosaina network chiitiko pane interface.)
    • Apo WAN interface yakanga yatogadziriswa, uye APN yakabatana, iyo WAN LED inenge ichivhenekera nekutsvuka. (Kana iri kupenya nekukurumidza, inosaina network chiitiko.)
    • Kana LAN neWAN zvichisvikika, iyo WAN LED ichashanda nebi-ruvara (tsvuku UYE girinhi panguva imwe chete), sezviri pachena neyero. Inopenya zviratidzo network chiitiko.

KUGADZIRA CHINHU

1. Vhura mudziyo wenzvimbo websaiti muMozilla Firefox browser, uko iyo default web mushandisi interface (LuCi) kero paEthernet port ndeye: https://192.168.127.1:8888
2. Pinda neZita reMushandisi: mudzi, Password: wmrpwd uye sundira kubhatani reKupinda.
3. Gadzirisa iyo SIM kadhi's APN marongero: vhura iyo Network / Interfaces menyu, WAN interface, Rongedza bhatani.
4. Zadza SIM #1 APN (APN kuseta yeSIM kadhi rako). Kana uine PIN kodhi paSIM kadhi yauri kushandisa, wedzera iyo chaiyo PIN pano. (Bvunza Mobile Operator yako.)
5. Dzvanya kune Save & Nyorera bhatani kuchengetedza marongero uye kugadzirisa cellular module. Nenguva isipi (~ 10-60 masekondi) iyo cellular module ichagadziridzwa maererano nezvirongwa zvitsva.
6. Ipapo mudziyo uchaedza kubatanidza uye kunyoresa SIM kune network. Kuvepo kweiyo nharembozha kuchasainwa neWAN LED (inopenya / inopenya negirinhi - pamwe neEthernet LED, apperently yero (tsvuku + yegirini LED chiitiko panguva imwe chete). Kana module yakanyoreswa zvakabudirira kuAPN, ichave iine data traffic pane WAN interface - tarisa paRx/Tx kukosha. Unogona kutarisa Status / Kupfuuraview menyu, Network chikamu kune rumwe ruzivo.
7. Kuti ugadzirise marongero eRS485, verenga Bhuku reMushandisi.

ZVINYORWA & SUPPORT

Zvinyorwa zvinogona kuwanikwa pachigadzirwa websaiti: https://m2mserver.com/en/product/wme-lcb/
Muchiitiko chekukumbira rutsigiro rwechigadzirwa, bvunza rutsigiro rwedu pa iotsupport@wmsystems.hu email kero kana tarisa rutsigiro rwedu websaiti kune mamwe mikana yekuonana ndapota: https://www.m2mserver.com/en/support/

Ichi chigadzirwa chakamisikidzwa nechiratidzo cheEC zvinoenderana nemirairo yeEuropean.
Chiratidzo chebhini chine mavhiri chinoreva kuti chigadzirwa pakupera kwehupenyu hwacho chinofanira kuraswa nemarara epamba mukati meEuropean Union. Rasa chete zvinhu zvemagetsi/magetsi muzvirongwa zvakaparadzana zvekuunganidza, izvo zvinopa kudzoreredza nekudzokorodza zvinhu zviri mukati. Izvi zvinoreva kwete chete kune chigadzirwa, asiwo kune zvimwe zvese zvishongedzo zvakanyorwa nechiratidzo chakafanana.

Zvinyorwa / Zvishandiso

WM SYSTEMS WM-E LCB IoT Load Control Chinja [pdf] Installation Guide WM-E LCB IoT Load Control Switch, WM-E LCB, IoT Load Control Switch, Load Control Switch, Control Switch, Switch

References

• User Manual