WM SYSTEMS WM-E LCB IoT Load Control Switch

LIBAKATSO

• Phepelo ea motlakase - Kenyelletso ea matla a AC, block ea terminal ea 2-pin
• Relay 1..2 - latching relay, 16A 250V AC, switch modes: NO, NC, COM, terminal block
• Relay 3..4 - latching relay, 16A 250V AC, switch mode: NC, COM, terminal block
• Likarolo tsa sehokelo sa RJ45:
  • Ethernet - 10/100MBit, boema-kepe ba RJ45, ka thapo ea UTP Cat5
  • RS485 - bakeng sa lisebelisoa tsa kantle ka mohala o nang le sebopeho sa Y
  • Sehokelo sa P1 - bakeng sa limithara tse bohlale ka mohala o bopehileng joaloka Y
• LED1..LED4/WAN – Maemo a LED
• SIM – Push kenya SIM card slot (mini SIM, type 2FF) micro-SD card slot – bakeng sa likarete tsa memori (max. 32 GByte)
• Ka hare LTE Antenna - sekhomaretsi, holim'a mountable

MAEMO A HAjoale & A TIRISO / HO SEBELISA

• Kenyelletso ea matla: ~ 100-240V AC, +10% / -10%, 50-60Hz +/- 5%
• Tšebeliso: Nyenyane: 3W / Karolelano: 5W / Max: 9W (0.25A)
• Likhetho tsa mojule oa mehala:
  • LTE Cat.1: Telit LE910C1-EUX (LTE Cat.1: B1, B3, B7, B8, B20, B28A / 3G: B1, B3, B8 / 2G: B3, B8)
  • LTE Cat.M / Cat.NB: Telit ME910C1-E1 (LTE M1 & NB1 B3, B8, B20)
• Mocheso oa ho sebetsa / oa polokelo: pakeng tsa -40'C le +85'C, 0-95% rel. mongobo
• Boholo: 175 x 104 x 60 limilimithara / Boima: 420gr
• Kakaretso: IP52 ABS polasetiki e nang le sekoaelo se pepeneneng, e ka beoa holim'a terene / leboteng

  

SCHEMATIC FIGURE OF INTERFACES, PINOUT

TLHOKOMELO! U SE KE UA KHOKELA ~ 100-240V AC POWER SOURCE ho pigtail AC CONNECTOR (24) KAPA POTUT EA MATLA (12) EA SESEBETSI ho fihlela u sa qete ka wiring!
HA U BULELA TŠEBELETSO, KA NAKO TSOHLE etsa bonnete ba hore PCB HA E HOKANE LE MOHLOLI OA MATLA 'me li-supercapacitor li khathetse (lipontšo tsa LED ha li sebetse) PELE HO HLOMELA PCB!

LIEKETSENG MOHATO

1. Tlosa polasetiki, sekoaelo se ka holimo sa koung e bonaletsang (1) ka ho lokolla sekoere (3) ho tloha ka holim'a sebaka se koalehileng.
2. Hlohlelletsa karolo ea polasetiki (1) ka hloko karolong e ka tlaase ea setsi (2), ebe u tlosa sekoahelo se ka holimo (1).
3. Hona joale o ka lokolla ho hokahanya lithapo le likhoele ho likoung le li-interfaces. Bula lihoko tsa polasetiki ka hloko (12) tsa sebaka sa motheo (2) ka screwdriver.
4. Hona joale setsi sa polasetiki se ka bonoa ka PCB e kopaneng (4) ka hare. Bula PCB (4) 'me u tlose ho tloha botlaaseng (2), ebe u fetola PCB holimo. Joale u ka bona karolo e ka tlase ea PCB.
5. Kenya SIM card e nyane (e kentswe tshebetsong ka APN) ho se tshoaro ya SIM (23). Sheba setšoantšo se leqepheng le latelang: moeli o sehiloeng oa SIM o tlameha ho lebisoa ho PCB 'me SIM chip e shebe fatše. Kenya le ho sututsa SIM ho fihlela e tlameletsoe (o tla utloa molumo oa ho tobetsa).
6. U ka sebelisa karete ea micro-SD haeba u batla (ho ikhethela). Ebe o kenya karete ya memori ho sekotjana sa karete ya mini-SD (22) ebe o e sututsa ho fihlela e tlamellwa ka tsela e sireletsehileng.
7. Joale khutlisa PCB 'me u e khutlisetse sebakeng se koetsoeng (2).
8. Sheba ho PCB hore thapo ea lenaka la LTE (16) e hoketsoe ho sehokelo sa Antenna RF (15).
9. Khutlisetsa karolo e ka holimo ea polasetiki e tšoeu ea ABS e ka tlosoang setsing (2) - hlahloba hore li-hook (12) lia koala.
10. Etsa wiring ho ea ka litlhoko - ho itšetlehile ka setšoantšo sa schematic (ka holimo).
11. Hokela AC power chord (AC pigtailed connector) lithapo (24) ho lithakhisa tse peli tsa pele (5) tsa sesebelisoa (ho tloha ka ho le letšehali ho ea ho le letona): e ntšo ho ea ho N (neutric), e khubelu ho ea ho L (mola).
12. Hokela lithapo tsa lisebelisoa tsa mabone (25) tsa lebokose la khabinete ea leseli la seterateng - ho liphetho tse hlokahalang tsa relay (6).
    Hlokomela hore RELAY 1..2 ke li-relays tsa latching, tse lumellang NO, NC, COM ho hokahanya le mekhoa ea ho fetola, ha RELAY 3..4 e na le NC, COM feela le mokhoa oa ho fetola.
13. Hokela mohala oa UTP o nang le sebopeho sa Y (27) - bakeng sa Ethernet / RS485 / P1 - kapa mohala o tobileng oa UTP (26) - bakeng sa Ethernet feela - ho ea boema-kepe ba RJ45 (7) - ho latela litlhoko. Lehlakore le leng la thapo ea Ethernet le lokela ho hokeloa ho PC ea hau kapa sesebelisoa sa kantle seo u batlang ho se hokela.
    Hlokomela, hore lithapo tsa RS485 / P1 ke lithapo tsa li-sleeve tse ikemetseng (28).

    

14. Hokela RS485 ho sesebelisoa sa kantle. Sehokelo sa P1 se fumaneha bakeng sa ho hokahanya mitha ea motlakase / modem ea metering e bohlale.
15. Khutlisetsa sekoahelo sa polasetiki se bonaletsang (1) botlaaseng (2).
16. Sekoahelo sa sesebelisoa se na le mefuta e 'meli ea ho lokisa, e lokelang ho rereloa ho phahamisa seporo kapa ho sebelisa li-screws tsa lintlha tse 3, kapa ho sebelisa hook (e leketlile leboteng / ka lebokoseng la khabinete ea leseli).
17. Hokela phepelo ea motlakase ea 100-240V AC ho sehokelo sa pigtail sa thapo ea motlakase ea AC (24) le mohloling oa motlakase o kantle / plug ea motlakase.
18. Sesebelisoa se na le sistimi e kentsoeng pele. Boemo ba hona joale ba sesebelisoa bo bontšoa ke mabone a eona a LED (11).
    • LESOA MAKHANYA - Sheba buka ea ho kenya bakeng sa lintlha tse ling.
    • REL.1: Relay#1 (mokhoa: NO, NC, COM) SET/RESET e fumaneha
    • REL.2: Relay#2 (mokhoa: NO, NC, COM) SET/RESET e fumaneha
    • REL.3: Relay#3 (mokhoa: NC, COM) ha ho phini ea RESET, SET e hanetsoe
    • REL.4: Relay#4 (mokhoa: NC, COM) ha ho phini ea RESET, SET e hanetsoe
    • LED ea WAN: bakeng sa khokahano ea marang-rang (ts'ebetso ea LAN/WAN)
      Hlokomela, hore sesebelisoa se na le karolo ea supercapacitor ka hare, e fanang ka ts'ebetso e sireletsehileng haeba ho ka ba le matlatage. Tabeng ea matla otage - ka lebaka la li-supercapacitor - e na le matla a lekaneng a ho fana ka ho khaola ho sireletsehileng le ho koala (pele li-supercapacitor li tla fela).
      Supercapacitor e ka khathala ka mor'a outage kapa haeba u boloka sesebelisoa ka likhoeli ntle le ho hokahanya matla. E tlameha ho lefisoa pele e sebelisoa

      

QALANG SETS'OANE

1. Ha o sebelisa sesebelisoa, recharge ea supercapacitor e tla qala ka bo eona. Sistimi ea sesebelisoa e tla qalisoa feela kamora pheletso ea ts'ebetso ea tefiso.
2. Hokela thapo ea Ethernet (UTP) lipakeng tsa segokanyimmediamentsi sa RJ45 sa sesebelisoa kapa adaptara ea eona ea sebopeho sa Y le koung ea Ethernet ea PC ea hau. (Sesebelisoa sa RS485 se lokela ho hokahanngoa le boema-kepe bo bong ba thapo ea Y.)
3. Lokisa sehokelo sa Ethernet khomphutheng ea hau bakeng sa protocol ea TCP/IPv4 bakeng sa ho seta aterese ea IP: 192.168.127.100 le subnet mask: 255.255.255.0
4. Qala sesebelisoa ka ho eketsa matla a AC ho kenyelletso ea matla (5).
5. Li-LED tsohle tse 'nè li tla be li se na letho ka metsotsoana e seng mekae - e tloaelehileng. (Haeba sesebelisoa se ne se sa sebelisoe ho tloha ka nako e telele, li-supercapacitor li tlameha ho lefisoa pele microcontroller e ka qala sesebelisoa.)
6. Ka mor'a metsotsoana e seng mekae feela LED ea WAN e tla be e ntse e khantša ka bofubelu ho fihlela li-supercapacitor li tla lefisoa (sesebelisoa se ntse se e-s'o qale). E ka nka metsotso e ka bang 1-4.
7. Ha tefiso e felile, sesebelisoa se tla qalisoa. E tla tekenoa ka mabone a khubelu a li-LED tsohle tsa relay (REL.1..4) bakeng sa metsotsoana ea 3 le ke WAN LED e khantšang ka botala haufinyane. Sena se bolela hore sesebelisoa se qalile.
8. Haufinyane, ha LED ea WAN e tla be e se na letho 'me li-LED tsohle tsa relay (REL.1..4) li tla lula li khantša ka bofubelu *, ho bolela hore sesebelisoa se ntse se qala. Ho nka metsotso e ka bang 1-2.*Hopola, haeba u se u hoketse relay, seo se tla tekena boemo ba hona joale ba relay ka boemo ba sona bo nepahetseng (bofubelu bo bolela ho TLOA, botala bo bolela ho ON).
9. Qetellong ea ts'ebetso ea boot, sesebelisoa se ka finyelloa ho li-interfaces tsa eona tsa marang-rang (LAN le WAN) haeba li ne li se li hlophisitsoe. Haeba sebopeho sa marang-rang sa hajoale se fumaneha, se saennoe ke lets'oao la WAN LED.
10. Ha sesebelisoa se fumaneha ho sebopeho sa LAN se hlophisitsoeng, WAN LED e tla khantša kamehla ka botala. (Haeba e benya ka potlako, e tšoaea tšebetso ea marang-rang ho sehokelo.)
    • Ha sebopeho sa WAN se se se hlophisitsoe, 'me APN e hokahane, WAN LED e tla khantša ka bofubelu. (Haeba e benya ka potlako, e bontša tšebetso ea marang-rang.)
    • Haeba LAN le WAN li fumaneha, WAN LED e tla sebetsa ka mebala e 'meli (e khubelu LE e tala ka nako e le' ngoe), ho bonahala e le mosehla. Matšoao a benyang tšebetso ea netweke.

TS'ELISO SEBAKA

1. Bula sebaka sa sesebelisoa webSebaka sa marang-rang ho sebatli sa Mozilla Firefox, moo ho sa feleng web aterese ea mosebelisi (LuCi) boema-kepeng ba Ethernet ke: https://192.168.127.1:8888
2. Kena ka Lebitso la Mosebelisi: motso , Password: wmrpwd ebe o tobetsa konopo ea Kena.
3. Lokisa litlhophiso tsa APN tsa SIM card: bula menu ea Network / Interfaces, WAN interface, Edita konopo.
4. Tlatsa SIM #1 APN (setting ea APN ea SIM card ea hau). Haeba u na le PIN khoutu ho SIM card eo u e sebelisang, kenya PIN e nepahetseng mona. (Botsa Mosebelisi oa hau oa Mohala.)
5. Tobetsa ho konopo ea Boloka & Sebelisa ho boloka litlhophiso le ho hlophisa module ea cellular. Haufinyane (~ 10-60 metsotsoana) module ea cellular e tla hlophisoa mabapi le litlhophiso tse ncha.
6. Ebe sesebelisoa se tla leka ho hokahanya le ho ngolisa SIM ho marang-rang. Ho fumaneha ha marang-rang a selefouno ho tla tekenoa ke WAN LED (e khanyang / e khanyang ka botala - hammoho le Ethernet LED, e mosehla ka nako e le 'ngoe (bofubelu + bo botala bo botala ba LED ka nako e le 'ngoe).view menu, Network karolo bakeng sa lintlha tse ling.
7. Ho lokisa li-setting tsa RS485, bala Bukana ea Mosebelisi.

LITLHAKISO LE TŠEHETSO

Litokomane li ka fumanoa sehlahisoa websebaka: https://m2mserver.com/en/product/wme-lcb/
Haeba ho na le kopo ea tšehetso ea sehlahisoa, botsa tšehetso ea rona ho iotsupport@wmsystems.hu aterese ea lengolo-tsoibila kapa hlahloba tšehetso ea rona websebaka sa marang-rang bakeng sa menyetla e meng ea ho ikopanya ka kopo: https://www.m2mserver.com/en/support/

Sehlahisoa sena se tšoailoe ka letšoao la CE ho latela melaoana ea Europe.
Letšoao la moqomo o fetisitsoeng le bolela hore sehlahisoa qetellong ea nako ea bophelo ba sona se lokela ho lahloa le litšila tse akaretsang tsa ka tlung ka har'a European Union. Lahla feela lisebelisoa tsa motlakase / tsa elektroniki ka har'a merero e arohaneng ea pokello, e sebetsanang le ho khutlisoa le ho sebelisoa hape ha lisebelisoa tse ka hare. Sena ha se bolele feela sehlahisoa, empa le lisebelisoa tse ling tsohle tse tšoailoeng ka letšoao le tšoanang.

Litokomane / Lisebelisoa

WM SYSTEMS WM-E LCB IoT Load Control Switch [pdf] Tlhophiso Tataiso WM-E LCB IoT Load Control Switch, WM-E LCB, IoT Load Control Switch, Load Control Switch, Control Switch, Switch

Litšupiso

• Bukana ea Mosebelisi