Beijer GT-1428 Digital Input Output Module
8 digital input (sink), 8 digital output (source), 24 VDC, 0.5 A, diagnostic, cage clamp, 18 pt e mafai ona aveese fa'amau
Doc ID: 137670
2025-02-20
Puletaofia © 2025 Beijer Electronics AB. Ua taofia aia tatau uma. O faʻamatalaga i totonu o lenei pepa e mafai ona suia e aunoa ma se faʻaaliga ma e tuʻuina atu e avanoa i le taimi o le lolomiina. Beijer Electronics AB fa'asaoina le aia e sui ai so'o se fa'amatalaga e aunoa ma le fa'afouina o lenei fa'asalalauga. E leai se matafaioi a Beijer Electronics AB mo soʻo se mea sese e ono aliali mai i lenei pepa. O exampO mea o lo'o i totonu o lenei pepa ua na'o le fa'amoemoe e fa'aleleia atili ai le malamalama i le fa'atinoga ma le fa'aogaina o masini. E le mafai e le Beijer Electronics AB ona tauaveina so'o se noataga pe afai o nei meaampo lo'o fa'aaogaina i fa'aoga moni. I totonu view o le lautele o talosaga mo lenei polokalama, e tatau i tagata fa'aoga ona maua le malamalama ia lava ina ia mautinoa o loʻo faʻaoga saʻo i la latou faʻaoga patino. O tagata e nafa ma le talosaga ma meafaigaluega e tatau ona latou mautinoa o talosaga taʻitasi o loʻo tausisia uma manaʻoga talafeagai, tulaga, ma tulafono e tusa ai ma le faʻatulagaina ma le saogalemu. Beijer Electronics AB o le a le taliaina se noataga mo soʻo se mea leaga na tupu i le taimi o le faʻapipiʻiina poʻo le faʻaogaina o meafaigaluega o loʻo taʻua i lenei pepa. Beijer Electronics AB fa'asaina uma suiga, suiga, po'o le liua o meafaigaluega.
Ofisa Ulu
Beijer Electronics AB
Pusa 426
201 24 Malmö, Suetena
www.beijerelectronics.com / +46 40 358600
E uiga i Lenei Tusi Taiala
This manual contains information on the software and hardware features of the Beijer Electronics GT-1428 Digital Input/Output Module. It provides in-depth specifications, guidance on installation, setup, and usage of the product.
Fa'ailoga o lo'o Fa'aaogaina i Lenei Tusi Lesona
O lenei lomiga e aofia ai le Lapata'iga, Lapata'iga, Fa'aaliga, ma Fa'ailoga Taua pe a talafeagai ai, e fa'asino atu ai le saogalemu po'o isi fa'amatalaga taua. O fa'ailoga tutusa e tatau ona fa'amatalaina fa'apea:
LAPATAIGA
O le ata o le Lapataiga o loʻo faʻaalia ai se tulaga lamatia, afai e le aloese, e ono iʻu ai i le oti poʻo se manuʻa tuga ma faʻaleagaina tele le oloa.
FAATUATUA
The Caution icon indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury and moderate damage to the product.
FAAMANATU
O le fa'ailoga Fa'amatalaga e fa'ailoa ai le tagata faitau i mea moni ma tulaga talafeagai.
TAUA
O le fa'ailoga Taua e fa'ailoa ai fa'amatalaga taua.
Saogalemu
- A'o le'i fa'aogaina lenei oloa, faamolemole faitau ma le faaeteete lenei tusi lesona ma isi tusi lesona talafeagai. Faʻalogo atoatoa i faʻatonuga saogalemu!
- E leai se mea e tupu ai le Beijer Electronics e nafa pe noatia mo mea leaga e mafua mai i le faʻaaogaina o lenei oloa.
- O ata, exampO tusi ma ata i lenei tusi lesona o loʻo aofia ai mo faʻamoemoega faʻataʻitaʻiga. Ona o le tele o fesuiaiga ma manaʻoga e fesoʻotaʻi ma soʻo se faʻapipiʻi faʻapitoa, e le mafai e le Beijer Electronics ona ave le matafaioi poʻo le noataga mo le faʻaaogaina moni e faʻavae i luga o le ex.amples ma ata.
Fa'ailoga o oloa
O le oloa o lo'o i ai tusipasi nei.
Lautele Manaomia Manaomia
LAPATAIGA
- Do not assemble the products and wires with power connected to the system. Doing so causes an “arc flash”, which can result in unexpected, dangerous events
(burns, fire, flying objects, blast pressure, sound blast, heat). - Aua le pa'i i poloka fa'amau po'o fa'aoga IO pe a fa'agasolo le faiga. O le faia o lea mea e ono mafua ai se te'i eletise, ta'avale pu'upu'u po'o le fa'aletonu o le masini.
- Never let external metallic objects touch the product when the system is running. Doing so may cause an electric shock, a short circuit or malfunction of the device.
- Aua le tu'u le oloa i tafatafa o mea e mu. O le faia faapea e ono tupu ai se afi.
- O galuega uma uaea e tatau ona faia e se inisinia eletise.
- Pe a taulimaina modules, ia mautinoa o tagata uma, fale faigaluega, ma le afifiina o loʻo faʻavae lelei. Aloese mai le pa'i atu i vaega o le ta'avale, o lo'o iai vaega fa'aeletoroni e mafai ona fa'aumatia e ala i le tu'uina atu o le eletise.
FAATUATUA
- 'Aua ne'i fa'aogaina le oloa ile si'osi'omaga e sili atu ile 60℃. Aloese mai le tu'u sa'o o le la.
- Aua ne'i fa'aogaina le oloa ile si'osi'omaga e sili atu ile 90% ole susū.
- Fa'aaoga i taimi uma le oloa i totonu o si'osi'omaga o lo'o iai le fa'aleagaina o le tikeri 1 po'o le 2.
- Fa'aoga uaea masani mo uaea.
E uiga i le G-series System
Ua uma le faigaview
- Feso'otaiga Feso'ota'iga Module – The network adapter module forms the link between the field bus and the field devices with the expansion modules. The connection to different field bus systems can be established by each of the corresponding network adapter modules, e.g., for MODBUS TCP, Ethernet IP, EtherCAT, PROFINET, CC-Link IE Field, PROFIBUS, CANopen, DeviceNet, CC-Link, MODBUS/Serial etc.
- Fa'alautele Module - Ituaiga module fa'alautele: Digital IO, Analog IO, ma fa'apitoa fa'apitoa.
- Feau - E lua ituaiga o feʻau e faʻaaogaina e le faiga: Feʻau tautua ma feʻau IO.
IO Fa'asologa o Fa'amaumauga Fa'afanua
An expansion module has three types of data: IO data, configuration parameters, and memory registers. The data exchange between the network adapter and the expansion modules is made via IO process image data by internal protocol.
Fa'asolo fa'amatalaga i le va o feso'ota'iga feso'ota'iga (63 avanoa) ma fa'alautele modules
The input and output image data depend on the slot position and the data type of the expansion slot. The ordering of the input and output process image data is based on the expansion slot position. Calculations for this arrangement are included in the manuals for the network adapter and programmable IO modules.
Fa'amaumauga fa'amaufa'ailoga aoga e fa'alagolago i modules o lo'o fa'aogaina. Mo example, modules analog ei ai tulaga o le 0-20 mA po o le 4-20 mA, ma modules vevela ei ai tulaga e pei o PT100, PT200, ma PT500. O faʻamaumauga mo module taʻitasi e tuʻuina atu ai se faʻamatalaga o faʻamaumauga faʻamau.
Fa'amatalaga
Fa'amatalaga Si'osi'omaga
| O le vevela o galuega | -20°C – 60°C |
| UL vevela | -20°C – 60°C |
| Teuga vevela | -40°C – 85°C |
| Susū fa'atusa | 5% - 90% lē faʻapipiʻiina |
| Fa'amauina | DIN nofoaafi |
| Faiga fa'ate'ia | IEC 60068-2-27 (15G) |
| Tete'e tetete | IEC 60068-2-6 (4 g) |
| Alamanuia fa'aoso | EN 61000-6-4: 2019 |
| Puipuiga fa'apisinisi | EN 61000-6-2: 2019 |
| Tulaga fa'apipi'i | Tusa'o ma faalava |
| Fa'ailoga oloa | CE, FCC, UL, cUL |
Fa'amatalaga Lautele
| Malosi'i atu | Max. 55 mA @ 5 VDC |
| Tu'ufua | I/O i le fa'aa'oa'oga: Fa'ato'a fa'atasi |
| Malosiaga fanua UL | Sapalai voltagu: 24 VDC numera, vasega 2 |
| Malosiaga fanua | Sapalai voltage: 24 VDC nominal Voltage va'aiga: 15 – 30 VDC
Malosi fa'amama: 40 mA @ 24 VDC |
| Uaea | I/O uaea maualuga. 0.75 mm2 (AWG 18) |
| mamafa | 63 g |
| Tele module | 12 mm x 109 mm x 70 mm |
Fua
Fua fa'atatau (mm)
Fa'amatalaga Fa'amatalaga
| Fa'aulu ile module | 8 points ituaiga goto |
| Fa'ailoga | 8 tulaga lanu meamata |
| I-setete voltage | 24 VDC nominal
15 – 30 VDC @ 60 ℃ |
| I-setete le taimi nei | 2.25 mA @ 24 VDC
3 mA @ 30 VDC |
| Ese-setete voltage | 8 VDC @ 25 ℃ |
| Fa'atuai fa'ailoga fa'aoga | OTI i ON: Max. 0.3 ms
ON i le OFF: Max. 0.3 ms |
| Fa'amama fa'aulu | Fa'atonu, e o'o atu ile 10 ms |
| Fa'atupu fa'alavelave fa'aoga | 10.2K Ω masani |
Fa'amatalaga Fa'amatalaga
| O mea e maua i le module | 8 points ituaiga puna |
| Fa'ailoga | 8 tulaga lanu meamata |
| Galuega faatino voltagu tele | 24 VDC nominal
15 – 30 VDC @ 60 ℃ |
| I-setete voltagu mataua | 0.3 VDC @ 25 ℃
0.6 VDC @ 60 ℃ |
| I-setete min. taimi nei | Min. 1 mA |
| I fafo atu o le setete leakout current | Max. 10 uA |
| Fa'ailo fa'ailo tuai | OTI i ON: Max. 0.1 ms
ON i le OFF: Max. 0.35 ms |
| Fa'ailoga o lo'o iai nei | Max. 0.5 A ile alalaupapa / Max. 4 A ile iunite |
| Puipuiga | Over current limit: 2.2 A @ 25 °C each channel Thermal shutdown: 175 °C
Puipuiga pupuu |
Ata uaea
| Pin nu. | Fa'amatalaga fa'ailoga |
| 0 | Auala ulufale 0 |
| 1 | Auala o fafo 0 |
| 2 | Auala ulufale 1 |
| 3 | Auala o fafo 1 |
| 4 | Auala ulufale 2 |
| 5 | Auala o fafo 2 |
| 6 | Auala ulufale 3 |
| 7 | Auala o fafo 3 |
| 8 | Auala ulufale 4 |
| 9 | Auala o fafo 4 |
| 10 | Auala ulufale 5 |
| 11 | Auala o fafo 5 |
| 12 | Auala ulufale 6 |
| 13 | Auala o fafo 6 |
| 14 | Auala ulufale 7 |
| 15 | Auala o fafo 7 |
| 16 | Ta'atele (Mata o fanua 0 V) |
| 17 | Ta'atele (Mata o fanua 24 V) |
Fa'ailoga LED
| LED Nu. | LED galuega / faʻamatalaga | Lanu LED |
| 0 (left side) | INPUT alavai 0 | Lanu meamata |
| 1 | INPUT alavai 1 | Lanu meamata |
| 2 | INPUT alavai 2 | Lanu meamata |
| 3 | INPUT alavai 3 | Lanu meamata |
| 4 | INPUT alavai 4 | Lanu meamata |
| 5 | INPUT alavai 5 | Lanu meamata |
| 6 | INPUT alavai 6 | Lanu meamata |
| 7 | INPUT alavai 7 | Lanu meamata |
| 0 (right side) | Auala OUTPUT 0 | Lanu meamata |
| 1 | Auala OUTPUT 1 | Lanu meamata |
| 2 | Auala OUTPUT 2 | Lanu meamata |
| 3 | Auala OUTPUT 3 | Lanu meamata |
| 4 | Auala OUTPUT 4 | Lanu meamata |
| 5 | Auala OUTPUT 5 | Lanu meamata |
| 6 | Auala OUTPUT 6 | Lanu meamata |
| 7 | Auala OUTPUT 7 | Lanu meamata |
Tulaga Alavai LED
LED no. 0-7 (left side)
| Tulaga | LED | Fa'ailoga |
| Leai se faailo | Tape | Fa'agaioiga masani |
| I luga o le faailo | Lanu meamata | Fa'agaioiga masani |
LED no. 0-7 (right side)
| Tulaga | LED | Fa'ailoga |
| Leai se faailo | Tape | Fa'agaioiga masani |
| I luga o le faailo | Lanu meamata | Fa'agaioiga masani |
| Fa'aletonu o alavai | moli | Short to GND Over current
Ova le vevela |
Fa'afanua Fa'amaumauga i le Laulau Ata
Ulufale fa'amaumauga fa'amaumauga
| D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 |
Fa'aofi le tau o ata
| Bit no. | Bit 7 | Bit 6 | Bit 5 | Bit 4 | Bit 3 | Bit 2 | Bit 1 | Bit 0 |
| Byte 0 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
| Byte 1 | D15 | D14 | D13 | D12 | D11 | D10 | D9 | D8 |
Fa'atauga ata
| Bit no. | Bit 7 | Bit 6 | Bit 5 | Bit 4 | Bit 3 | Bit 2 | Bit 1 | Bit 0 |
| Byte 0 | D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
Output module data
| D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
Fa'amatalaga Parameter
Umi ta'otoga aoga: 4 paita
| Bit no. | Bit 7 | Bit 6 | Bit 5 | Bit 4 | Bit 3 | Bit 2 | Bit 1 | Bit 0 |
| Byte 0 | Fault action (ch0 – ch7) 0: Fault value
1: Hold last state |
|||||||
| Byte 1 | Fault value (ch0 – ch7) 0: Off
1: i luga |
|||||||
| Byte 2 | Tau fa'amama fa'aulu: 0 – 10 (iunite: ms) | |||||||
| Byte 3 | Fa'apolopolo | |||||||
Seti Meafaigaluega
FAATUATUA
- Faitau i taimi uma lenei mataupu aʻo leʻi faʻapipiʻi le module!
- vevela luga! E mafai ona vevela le pito i luga ole fale ile taimi ole gaioiga. Afai e fa'aoga le masini i le maualuga o le vevela, tu'u pea le masini e mālūlū a'o le'i tago i ai.
- O le galue i masini fa'amalosi e mafai ona fa'aleagaina ai masini! Tape i taimi uma le paoa a'o le'i galue i le masini.
Avanoa Manaomia
The following drawings show the space requirements when installing the G-series modules. The spacing creates space for ventilation and prevents conducted electromagnetic interference from influencing the operation. The installation position is valid vertically and horizontally. The drawings are illustrative and may be out of proportion.
FAATUATUA
LE le mulimulitaia o avanoa e mana'omia e ono i'u ai i le fa'aleagaina o le oloa.
Mauga Module i le DIN Rail
O mataupu o loʻo mulimuli mai o loʻo faʻamatalaina pe faʻafefea ona faʻapipiʻi le module i le DIN rail.
FAATUATUA
O le module e tatau ona faʻapipiʻi i le DIN rail faʻatasi ai ma le loka loka.
Mauga GL-9XXX poʻo GT-XXXX Module
O fa'atonuga nei e fa'atatau i nei ituaiga module:
- GL-9XXX
- GT-1XXX
- GT-2XXX
- GT-3XXX
- GT-4XXX
- GT-5XXX
- GT-7XXX
GN-9XXX modules e tolu loka loka, tasi i le pito i lalo ma le lua i le itu. Mo faʻatonuga faʻapipiʻi, vaʻai ile Mount GN-9XXX Module.
Mauga GN-9XXX Module
E fa'apipi'i pe fa'ae'e se feso'ota'iga feso'ota'iga po'o le module IO e mafai ona fa'apolokalameina ma le igoa oloa GN-9XXX, mo leample GN-9251 poʻo le GN-9371, vaʻai i faʻatonuga nei:
Mauga Aveese Aveese Poloka Terminal
Ina ia fa'apipi'i pe fa'ae'e se poloka fa'amau e mafai ona aveese (RTB), va'ai fa'atonuga o lo'o i lalo.
Fa'afeso'ota'i Uaea ile Poloka Fa'amau e Ave'esea
Ina ia fa'afeso'ota'i/ motusia uaea i/mai le poloka fa'amau e mafai ona aveese (RTB), va'ai fa'atonuga o lo'o i lalo.
LAPATAIGA
Fa'aaoga i taimi uma le sapalai fautuaina voltagu ma taimi e puipuia ai le faaleagaina o meafaigaluega ma mautinoa lelei le faatinoga.
Malosi o fanua ma pine fa'amaumauga
Feso'ota'iga i le va o le feso'ota'iga feso'ota'iga G-series ma le fa'alauteleina o le module, fa'apea fo'i ma le fa'aogaina o le eletise o le fa'aogaina o pasi, e fa'atinoina e ala i le pasi totonu. E aofia ai 2 Field Power Pins ma 6 Data Pins.
LAPATAIGA
Aua ne'i pa'i i fa'amaumauga ma pine mana o le fanua! O le pa'i e mafai ona i'u ai i le palapala ma le fa'aleagaina e le pisa ESD.
| Pin nu. | Igoa | Fa'amatalaga |
| P1 | VCC faiga | Sapalai faiga voltage (5 VDC) |
| P2 | System GND | Eleele faiga |
| P3 | Token output | Token outport port of the processor module |
| P4 | Fa'asologa fa'asologa | Tulaga fa'aulufale fa'aliliu o le module fa'agaioiga |
| P5 | Fa'asinomaga fa'asologa | O le tali fa'aoga uafu o le fa'aogaina o le module |
| P6 | Fa'apolopolo | Fa'apolopolo mo fa'ailoga e pasi |
| P7 | fanua GND | fanua fanua |
| P8 | VCC fanua | Sapalai fanua voltage (24 VDC) |
Beijer Electronics, Doc ID: 137670
Pepa / Punaoa
 |
Beijer GT-1428 Digital Input Output Module [pdf] Tusi Taiala GT-1428, GT-1428 Digital Input Output Module, GT-1428, Digital Input Output Module, Input Output Module, Output Module, Module |