MAULsirius 825 93 LED Lamp Assembly

This guide details the assembly process for the MAULsirius 825 93 LED lamp system, covering the connection of various components including LED drivers and modules.

Components

The MAULsirius 825 93 system comprises several key parts:

MAULsirius Lamp Body
HEP GROUP LED Driver LCV70W48 UNI (Art.-No.: 8259209.210)
LED Module Strips (Art.-No.: 8259209.205, 8259209.200)
Driver Board (Art.-No.: 8259309.220)
Small Circuit Board / Sensor Module (Art.-No.: 8259209.225)
Power Cable (Art.-No.: 8259309.160)

The system utilizes LED illumination (?) and supports dimming (?️).

Assembly Steps

Step 1: Initial Setup

The lamp body base is shown with a power cable and screw mounting points.

(Visual: Page 3)

Step 2: Connector Operation (Pull/Push)

A connector with multiple wires is shown. To connect or disconnect, perform the following actions:

"PULL b)" [pull connector tab b]
"PUSH a)" [push connector tab a]

(Visual: Pages 4, 12, 16)

Step 3: Wire Handling

Instructions indicate to "PULL" wires for connection or disconnection.

(Visual: Page 5)

Step 4: Securing Components with Screws

Use a PH1 screwdriver (?) to insert screws into designated holes on the lamp housing.

(Visual: Pages 6-7)

Step 5: Attaching LED Modules

The LED module strips (Art.-No.: 8259209.205, 8259209.200) are attached to the lamp body using screws. Use a PH2 screwdriver (?) for these fastenings.

The main lamp body label shows "MAUL" and "Art-No. 82592".

(Visual: Pages 8, 14, 17, 19-25)

Step 6: Connecting LED Modules

Connect the LED modules to the main system using the specified connector operations ("PULL b)", "PUSH a)").

(Visual: Pages 15-16)

Step 7: Sliding Component Insertion

A component is shown being slid into its designated position.

(Visual: Page 11)

Step 8: Strong Connection Pull

An instruction indicates to "PULL STRONGLY" on a specific connector to ensure a secure connection.

(Visual: Page 10)

Step 9: Connecting the LED Driver

Connect the HEP GROUP LED Driver LCV70W48 UNI (Art.-No.: 8259209.210) to the system. Secure it with screws as indicated.

(Visual: Pages 12-13)

Step 10: Installing the Driver Board

Install the driver board (Art.-No.: 8259309.220, LS-HC V07). Connect it and secure it using a PH2 screwdriver (?).

(Visual: Pages 27-31)

Step 11: Installing the Sensor Module

Install the small circuit board / sensor module (Art.-No.: 8259209.225, LS-TLED-GAN-V1.1). Connect it and secure it using a PH1 screwdriver (?).

(Visual: Pages 32-34)

Step 12: Final Adjustments and Connections

Perform final connections and adjustments, which may include "PULL a)" actions and "ROTATE b)" operations for specific modules or sensors.

(Visual: Pages 33)

Step 13: Final Securing

Ensure all components, including the driver board, are securely fastened.

(Visual: Page 34)

Component Specifications

HEP GROUP LED Driver LCV70W48 UNI

Article Number: 8259209.210
Supply Voltage: 100-277V AC
Output: Max. 60VDC
Current: 390mA
Frequency: 50-60Hz
Temperature Range: -20°C to +50°C

MAULsirius Lamp Body Label

Article Number: 82592
Input Voltage: 200-240V 50/60Hz
Max Operating Temperature: +45°C

Driver Board (LS-HC V07)

Article Number: 8259309.220

Sensor Module (LS-TLED-GAN-V1.1)

Article Number: 8259209.225

Safety Precautions

Always observe safety instructions (⚠️ [read manual]) and ensure correct installation practices are followed to prevent hazards.

	MAULsirius 825 92 LED Lamp Component Guide and Replacement Instructions A comprehensive guide detailing the components and replacement procedures for the MAULsirius 825 92 LED lamp. Includes article numbers for LED strips, driver boards, and power supplies, along with step-by-step visual instructions for disassembly and assembly.
	MAULsirius 825 93 LED Desk Lamp - User Manual and Features Detailed instructions and features for the MAULsirius 825 93 LED desk lamp, including assembly, operation, motion sensor, and daylight sensor functionalities.
	MAULjuvis 825 86 LED Lamp Assembly and Maintenance Guide Detailed instructions for assembly, disassembly, and maintenance of the MAULjuvis 825 86 LED lamp, covering component identification, removal, and reassembly procedures.
	MAULsenja 825 88 LED Floor Lamp Assembly and Component Guide Detailed guide for the MAULsenja 825 88 LED floor lamp, covering component identification, assembly, and disassembly. Includes information on LED drivers and strips.
	MAULjuvis 825 87 LED Luminaire Assembly and Service Guide Comprehensive guide for the MAULjuvis 825 87 LED luminaire, detailing assembly, disassembly, and component replacement. Features information on the EOKE LED driver and various MAUL LED modules.
	MAULjaval 825 84 LED Floor Lamp: Maintenance and Replacement Guide Detailed instructions for maintaining and replacing the LED module and driver of the MAULjaval 825 84 LED floor lamp. Includes part numbers, specifications, and step-by-step guidance.
	MAULjaval 825 83 LED Lamp Service and Parts Replacement Guide Detailed instructions for servicing and replacing components of the MAULjaval 825 83 dimmable LED floor lamp, including LED modules and drivers.
	MAULjura 82571 LED Floor Lamp Assembly and Component Guide Comprehensive guide for assembling and replacing components of the MAULjura 82571 dimmable LED floor lamp, detailing steps for LED modules, driver, and dimmer installation.