Required Tools
The following tools are recommended for assembly:
- Phillips head screwdriver ?
- Flathead screwdriver ?
- Pencil ✏️
- Hammer ?
Important Note: The assembly process may require careful attention. If you encounter difficulties, please refer to IKEA support. ?
Parts List
| Quantity | Part Number | Description |
|---|---|---|
| 8x | 110519 | Screw |
| 20x | 118331 | Cam bolt |
| 20x | 101345 | Dowel |
| 20x | 120076 | Cam lock |
| 12x | 100365 | Screw |
| 4x | 115339 | Screw |
| 1x | 101221 | Bag of nails/tacks |
| 4x | 153548 | Handle/Knob |
| 2x | 10056137 | Drawer slide rail |
Assembly Steps
Step 1
Prepare the base panels. Insert cam bolts (118331) into the designated holes on two base panels. Use 8 cam bolts in total for this step.
Visual: Two flat panels are shown. Cam bolts are being screwed into pre-drilled holes.
Step 2
Attach handles/knobs (153548) to the front edges of the two base panels. Use 4 handles/knobs in total.
Visual: The two base panels from Step 1 are shown. Handles are being attached to their front edges.
Step 3
Insert dowels (101345) into the side panels. Attach the side panels to the base panels prepared in Step 1. Use 8 dowels in total.
Visual: Two vertical side panels are shown with dowels inserted. They are being connected to the base panels.
Step 4
Insert cam locks (120076) into the corresponding holes on the side panels. Secure the side panels to the base by turning the cam locks.
Visual: Cam locks are being inserted into the side panels and then turned to secure the connection to the base.
Step 5
Place the top panel onto the assembled structure. Ensure it aligns with the dowels and cam bolts.
Visual: The top panel is being lowered onto the partially assembled frame.
Step 6
Attach the back support piece. This piece typically runs horizontally across the back of the unit.
Visual: A horizontal piece is being attached to the rear of the unit.
Step 7
Attach drawer runners (118331) to the inside of the side panels. Use 4 runners in total (2 per side). Ensure correct orientation.
Visual: Drawer slide rails are being screwed onto the inner surfaces of the side panels.
Step 8
Attach the top panel. Ensure correct orientation; an incorrect placement is indicated by a cross symbol ❌.
Visual: The top panel is being attached. A diagram shows a warning against incorrect placement.
Step 9
Attach drawer runners (120076) to the main body of the unit. Use 4 cam locks in total.
Visual: Drawer slide components are being attached to the interior of the main cabinet structure.
Step 10
Begin attaching the back panel. Use one nail (101221) to secure a corner of the back panel.
Visual: The back panel is being positioned, and a nail is being hammered into place at a corner.
Step 11
Continue securing the back panel. Use one nail (101221) to attach another section of the back panel.
Visual: Another nail is being hammered into the back panel.
Step 12
Continue securing the back panel. Use one nail (101221) to attach another section of the back panel.
Visual: Another nail is being hammered into the back panel.
Step 13
Fully secure the back panel. Use 27 nails (101221) to attach the entire back panel to the unit. Ensure it is square.
Visual: Multiple nails are being hammered along the edges of the back panel to secure it.
Step 14
Assemble the second side panel structure. Attach cam bolts (118331) to the base panel. Use 4 cam bolts.
Visual: Similar to Step 1, but for the second side assembly.
Step 15
Insert dowels (101345) into the second set of side panels. Use 4 dowels.
Visual: Dowels are being inserted into side panels.
Step 16
Insert cam locks (120076) into the second set of side panels. Use 4 cam locks.
Visual: Cam locks are being inserted into side panels.
Step 17
Attach the second set of side panels to their base. Ensure alignment.
Visual: The second set of side panels is being connected to its base.
Step 18
Attach the top panel to the second side assembly.
Visual: The top panel is being attached to the second side assembly.
Step 19
Connect the two main assemblies. Use screws (110519, 4x) and screws (115339, 2x) to join the main cabinet body to the side panel assemblies.
Visual: The two main structures are being joined together using screws.
Step 20
Attach the drawer slide rails (10056137) to the main body and the drawer components (labeled DL and DR). Use screws (100365) for attachment.
Visual: Drawer slide rails are being mounted onto the cabinet interior and the drawer parts.
Step 21
Insert the assembled drawer into the chest. The drawer is shown being slid into place.
Visual: The completed drawer is being inserted into the chest.
