Yaheetech Hall Tree Assembly Instructions
Model # 611126
Introduction
Dear Customers,
Thank you for purchasing a Yaheetech product. Please read this instruction manual carefully before attempting to install.
Important Assembly Information:
- Please follow the instruction manuals and use a pad to avoid damage during assembly.
- For easier and better assembly, 2 or more adults are required.
- The expected assembly time for this product is 0.5 hours, depending on individual manipulative ability.
Safety and Care Instructions
- [No children] Not intended for use by children. Please keep your children closely supervised.
- [Keep away from heat] Keep away from fire or other heat sources.
- [No harsh cleaner] Do not use harsh cleaner for cleaning!
- [Wear gloves] We recommend wearing protective gloves for assembly.
- [Sort parts] Identify, sort and count the parts before assembly.
The warnings, cautions, and instructions listed in this manual may not cover all possible situations that may arise when using the product. Please contact help@yaheetech.shop if you need further help.
Parts List
- ① x2: Long, flat panels (side supports for bench base)
- ② x1: Long, flat panel (main vertical support)
- ③ x1: Long, flat panel (main vertical support)
- ④ x4: Short, flat pieces (base connectors)
- ⑤ x2: Short, flat pieces (shelf supports)
- ⑥ x1: Short, flat piece (connector)
- ⑦ x2: Short, flat pieces (lower shelf supports)
- ⑧ x2: Short, flat pieces (lower shelf supports)
- ⑨ x12: Cylindrical dowels/pegs
- ⑩ x1: Long, flat panel (top bar with hooks)
- ⑪ x2: Rectangular panels (bench seat, middle shelf)
- ⑫ x1: Long, flat panel (back support)
- ⑬ x1: Long, flat panel (back support)
- A x4: Round, flat pieces with screw head slot (screws)
- B x2: Round, flat pieces (screws)
Hardware List
- C x2: Screws, 35mm
- D x18: Screws, 30mm
- E x12: Screws, 25mm
- F x4: Screws
- G x8: Screws
- H x24: Small screws/bolts
- I x1: Allen wrench [tool]
- J x2: Small brackets/connectors
Assembly Steps
Diagram 1: Base Frame Assembly
Assemble the base frame. Connect parts ① (x2) to supports ④ (x4), ⑤ (x2), ⑥ (x1), ⑦ (x2), ⑧ (x2) using dowels ⑨ (x12) and screws H (x24).
Note: During assembly, please first half-tighten all screws into the holes. After all screws are set, fully tighten them.
Diagram 2: Attach Shelves to Base
Attach the middle shelf (⑪) and lower shelf supports (⑤) to the base structure using screws D (x18).
Note: During assembly, please first half-tighten all screws into the holes. After all screws are set, fully tighten them.
Diagram 3: Attach Top Bar and Back Supports
Attach the top bar (⑩) and back support panels (⑫, ⑬) to the vertical supports (②, ③) using screws E (x12) and A (x4).
Note: When installing Part ⑩, the side with 2 holes should face the front of the rack.
Note: During assembly, please first half-tighten all screws into the holes. After all screws are set, fully tighten them.
Diagram 4: Attach Main Vertical Supports
Attach the main vertical supports (②, ③) to the base structure using brackets J (x2) and screws F (x4).
Note: During assembly, please first half-tighten all screws into the holes. After all screws are set, fully tighten them.
Diagram 5: Attach Bench Seat and Shelves
Attach the bench seat (⑪) and shelves to the main vertical supports (②, ③) using screws F (x4) and J (x2).
Note: During assembly, please first half-tighten all screws into the holes. After all screws are set, fully tighten them.
Diagram 6: Attach Top Section with Hooks
Attach the top section with hooks (⑩) to the main vertical supports (②, ③) using screws C (x2) and G (x8).
Note: When installing Part ⑥, the side in which the hole near the border should face the front of the rack. (This note appears to be a general instruction about part orientation, potentially misplaced or referring to a different step/part).
Note: During assembly, please first half-tighten all screws into the holes. After all screws are set, fully tighten them.
Diagram 7: Final Adjustments
Secure the structure using screws B (x2) for parts ⑦ and ⑧. If alignment issues occur, loosen screws on parts ⑫ and ⑬ for adjustment.
Note: If meeting difficulties when assembling Part 8, please loosen the screws on two sides of Part 12 and Part 13 for adjustment.
Diagram 8: Final Product and Maintenance
The Yaheetech Hall Tree is now assembled. It is a vertical unit featuring a bench, shelves, and numerous coat hooks for entryway organization.
Yaheetech Product Information:
Thank you for purchasing a Yaheetech product! At Yaheetech, we are dedicated to bringing you the best online shopping experience and making your life comfortable. We pride ourselves on an integrated supply chain team that works meticulously to deliver you products and service with greatest value. Our networks span across the US, the United Kingdom, Germany, France and six more European countries. It is always our belief that how customers view our business and service ultimately defines our brand.
Feedback:
So, how did we do? Please let us know by making an online remark about it.
Good job. Would you like to share your experience to assist others with their shopping decisions?
[Not good] If you are not satisfied with this shopping experience, please contact us via help@yaheetech.shop.
Maintenance:
Check every 6 months that all assembly fastenings are properly tightened and retighten when necessary.
