Arrow Elite™ Kayak Manual

Parts and Components

The following components are included with the Arrow Elite™ Kayak (Model 65179):

Diagrams are for illustration purposes only. May not reflect actual product. Not to scale.

Important Safety Instructions

Save These Instructions – Read carefully before operating. Follow all safety and operating instructions. Failure to do so may cause the boat to overturn or explode, resulting in injury or death.

Warnings

• Before each use, thoroughly inspect all boat components, including air chambers, grab ropes, oars, and air valves, to ensure they are in good condition and securely fastened. Repair any damage before use.
• Never exceed the specified passenger numbers and load weights. Refer to the Product Descriptions for your boat's capacities. Exceeding weight limits can lead to overturn and drowning.
• Inflate according to the numbered air chambers and rated pressure indicated on the boat. Overinflation can cause explosion. Exceeding capacity plate data may damage the craft, cause overturn, or lead to drowning.
• Maintain balance in the boat. Uneven distribution of people or weight can cause overturning and drowning.
• Be aware of offshore winds and currents.
• Avoid leaving the boat exposed to direct sunlight for extended periods, as high temperatures can increase air expansion and cause irreparable damage.
• Never transport the boat while inflated on a vehicle. Be aware of potential damage from liquids like battery acid, oil, or petrol.
• When in deep water, board via the stern using the safety rope or handle. Always hold onto a rope or handle at the bow or stern, choose a lower position, and remain calm.

Technical Safety Instructions

• Do not exceed the maximum recommended number of people. The total weight of people and equipment must not exceed the maximum recommended weight capacity. Always use provided seating.
• When loading, never exceed the maximum recommended weight capacity. Distribute loads appropriately for trim (approximately level). Avoid placing heavy weights high up.
• The maximum recommended weight capacity includes all people, provisions, personal effects, equipment, cargo, and consumable liquids.
• Always use pre-inspected life-saving devices such as life jackets and buoys.
• Keep buckets, water scoops, and air pumps readily available for air leaks or water ingress.
• All passengers must remain seated while the boat is in motion to prevent falling overboard.
• Use the boat in protected shore zones, up to 300m (984 feet). Be cautious of natural factors like wind, tides, and tidal waves.
• Exercise caution when landing on shores. Sharp or rough objects (rocks, cement, shells, glass) can puncture the boat.
• If one chamber is punctured, fully inflate the other air chamber to prevent sinking.
• Do not drag the boat on rough surfaces to prevent damage.
• Always wear a life jacket!
• The owner/operator is responsible for having at least one secured bucket/bailer on board.
• Do not neglect safety rules; this could jeopardize your life and others'.
• Follow these instructions to avoid drowning, paralysis, or other serious injuries.
• Learn how to operate a boat. Check local information and training resources for boating regulations and dangers.

Product Specifications

Setup Instructions

Parts & Tools Needed

Compare the parts in your box to the parts listed in this manual. Verify that the equipment components represent the model that you had intended to purchase.

Recommendations During Installation – Warnings & Overview

Never use high-pressure air to inflate your boat. This will lead to damage and void your warranty (if applicable).

• Only use Bestway® approved inflation pumps.
• Never stand on or rest objects on the boat during inflation.
• Inflate the chambers until you can see some folding at the welding seams. After inflation, compare the pressure gauge with the value mentioned in this manual. DO NOT OVER-INFLATE.
• The pressure gauge is for inflation purposes only; its value is for reference and should not be used as a precision instrument.
• Always check the inflation pressure before using the boat. Ensure the boat has reached the correct pressure mentioned in this manual and printed near the inflation valve.
• Be sure the valve is tightly closed before using the boat. Never open the air valve cap while the boat is in use.
• After the craft is inflated, connect the belts of the seats and footrests to the side buckles on the craft. The location of the seats and footrests can be adjusted along with the craft floor.

Assembly Instructions

For installation instructions, follow the illustrations inside the manual. Drawings are for illustration purposes only. May not reflect actual product. Not to scale.

* Safety ropes are required when using the boat to comply with boating-related safety regulations. Please ensure they are properly tied as shown.

Assembly Steps:

1. Attach fins (E, F1, F2) to the designated slots on the kayak hull.
2. Assemble the paddle (B) by connecting its sections.
3. Inflate the kayak chambers using the air pump (G) to the recommended pressure of 0.7 bar (10 psi). Ensure valves are closed after inflation.
4. Connect the seats (C) and footrests (D) to the side buckles on the kayak.

Repair Patch Instructions

If there is a small puncture, repair it according to the instructions on the repair patch. If the hole is too big to be repaired with the provided patch, purchase a Bestway repair kit or send the boat to a specialty shop for repairs.

Disassembly Instructions

To deflate, open the air valves by pushing the control stem in and rotating until the valves stay open. Deflate all hull chambers simultaneously so the air pressure drops together.

Extended sun exposure can shorten the lifespan of your boat. Do not leave boats in direct sunlight for more than 1 hour after use.

Maintenance & Storage

• Use the spanner ⚙️ to tighten the air valve if it is leaking.
• Remove the paddles from the oar clasps and detach the seats.
• It is necessary to remove all residual air inside the chambers before storage. Fold the boat from front to back to remove additional air.
• Carefully clean the boat using mild soap and clean water. Do not use acetone, acid, or alkaline solutions.
• Use a cloth to gently dry all surfaces. The product can be dried under direct sunlight for 1 hour or less; do not exceed this recommendation, as extended sun exposure can shorten the boat's lifespan.
• Store in a dry place, with a temperature higher than 15°C (59°F), out of reach of children.