MCombo Wooden Cat House

Product Precautions

• Read and follow the information in the user's manual.
• Please keep kids away from small components to ensure safety. ⚠️ [child safety]
• Please ventilate before use. ?️
• Do not place overweight items. ?️ [heavy load]
• Please note that the wood is not chew-proof. ? [chew warning]
• Please clean up water stains and pet excrement in time. ??
• Please handle wood and other accessories properly. ?

Disclaimer

We ask that you read this manual completely before assembling and operating your new item. MCombo is not responsible for any damage or injury incurred due to improper or unsafe use of the item. MCombo specifically disclaims responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances. Please keep this manual for future reference.

Installation Preparation

1. Please prepare a carpet or mat to protect your floor. You need to spread out all the accessories.
2. Please prepare a pair of gloves to avoid being scratched by sharp wooden sawdust that may occur during installation.
3. Please open all the boxes to check that the accessories are complete and in good condition (The accessories list in page 3).
4. The box contains some small components, please place them properly before installation to keep them away from kids and ensure safety.
5. If you need to use power tools to install this product, please set the speed to low speed in advance. Due to the characteristics of wood products, the use of high speed during installation is probably to damage the wood.
6. When installing, please align all the holes and do not tighten all the screws first, otherwise it may make the installation difficult.

Illustration showing two figures standing, one holding an open book, with wooden planks and components laid out on the floor, suggesting preparation for assembly.

Accessories List

Kindly Notes:

⚠️ Please open all boxes to check the quantity and condition of accessories.

Q: Is there any broken or missing part?

A: If yes, please feel free to contact us (see page 14), we will do our best to assist you to solve the problem as soon as possible.

Installation Instruction

Q: How to deal with parts without holes?

A: Do not worry! Due to slight deviation during installation, only pilot holes are marked. Please align the parts and install them according to the manual.

Step 1

Attach parts A and B using hardware (11).

Diagram shows two identical rectangular frames (A and B) being joined by screws (11) at multiple points.

Step 2

Attach parts A and B to the main structure using hardware (4).

Diagram shows parts A and B being connected to a base structure (implied) using screws (4).

Step 3

Attach parts G and H to part A using hardware (3).

Diagram shows two tall, slatted frames (G and H) being attached to frame A using screws (3).

Step 4

Attach part O to the assembled structure (G, H, A) using hardware (10, 11).

Diagram shows a panel with a circular opening (O) being attached to the existing structure using screws (10) and (11).

Step 5

Attach part C to the structure using hardware (11).

Diagram shows a rectangular frame (C) being attached to the structure using screws (11).

Step 6

Assemble the upper section with parts I, J, C, O, Q using hardware (3, 4).

Diagram shows the assembly of the upper tier, connecting frames (I, J), panel (C), panel (O), and panel (Q) with screws (3) and (4).

Step 7

Attach part P to the structure using hardware (10).

Diagram shows a panel with a circular opening and shelf (P) being attached to the structure using screws (10).

Step 8

Attach parts D, E, F to the structure using hardware (9).

Diagram shows panels (D, E, F) being attached to the main frame using screws (9).

Step 9

Connect parts G, P, H to the main frame using hardware (11).

Diagram shows the connection of frames (G, H) and panel (P) to the main structure using screws (11).

Step 10

Attach part M to D and H using hardware (3, 9).

Diagram shows a panel with two circular openings (M) being attached to panels (D) and (H) using screws (3) and (9).

Step 11

Attach casters (14, 15) to the front side of the structure using hardware (2, 16).

Diagram shows casters (14, 15) being attached to the bottom front corners of the structure using screws (2) and brackets (16).

Step 12

Attach hardware (11) to the top of the structure.

Diagram shows screws (11) being inserted into the top of the assembled structure.

Step 13

Attach part N to the top of the structure using hardware (3, 9).

Diagram shows a slatted panel (N) being attached to the top of the structure using screws (3) and (9).

Step 14

Attach part P to the structure using hardware (4).

Diagram shows panel (P) being attached to the structure using screws (4).

Step 15

Attach parts W to P and O using hardware (5, 6).

Diagram shows two spherical/cylindrical parts (W) being attached to panels (P) and (O) using screws (5) and (6).

Step 16

Attach part U to the top of the structure using hardware (8, 10).

Diagram shows a rectangular panel (U) being attached to the top of the structure using screws (8) and (10).

Step 17

Attach parts Q, R, S to the structure using hardware (9, 10).

Diagram shows panels (Q, R, S) being attached to the structure using screws (9) and (10).

Step 18

Attach part T to the structure using hardware (8, 10).

Diagram shows panel (T) being attached to the structure using screws (8) and (10).

Step 19

Attach part V to P using hardware (2, 8).

Diagram shows panel (V) being attached to panel (P) using screw (2) and hardware (8).

Step 20

Attach parts K and L to the structure using hardware (1).

Diagram shows frames (K) and (L) being attached to the structure using screws (1).

Step 21

Attach hardware (7, 12) to the sides of the structure.

Diagram shows screws (7) and casters/wheels (12) being attached to the sides of the structure.

Step 22

Attach casters (13) to the bottom using hardware (1).

Diagram shows casters (13) being attached to the bottom of the structure using screws (1).

Step 23

Wall mounting preparation. The parts marked with ✔ are required for this installation step.

Diagram shows wall anchors, brackets, and screws for wall mounting. Includes a note: "Please Note: According to the height of the cabinet, find the right place to drill the hole in the wall."

Step 24

Wall mounting preparation. The parts marked with ✔ are required for this installation step.

Diagram shows brackets and screws for wall mounting.

Step 25

Final wall mounting attachment. The parts marked with ✔ are required for this installation step.

Diagram shows the final attachment of the cabinet to the wall using brackets and screws.

Step 26

FINISH. The fully assembled MCombo Wooden Cat House.

Diagram shows the completed wooden cat house with multiple levels and doors.

Warranty

Limitations Applicable to All Warranties

All warranties begin on the date of delivery. All warranties are to the original purchaser from MCombo /ExacMe ONLY.

Warranty Detail Explanation

• MCombo will replace the defective parts or send a replacement item provided that the warranty parts have not been subjected to misuse, abuse, or improper service by the consumer, for example, damaged part arising in consequence of negligence or improper operation.
• Exclusions also include components with damage caused by: Contamination, Abuse, misuse, accident or negligence, Commercial use, or use other than normal, Improper operation maintenance, or storage.
• MCombo will pay standard shipping rates on all warranted parts for the first year. MCombo can also sell you the replacement part for a discount price when your item is out of warranty policy.

Return/Replacement Policy

MCOMBO: All items come with a 30-day return/replace policy. During this time, MCombo will cover the shipping cost of return and replacement for a defective and damaged item, and provide a pre-paid return label or pick-up service for customer's convenience.

Note: Please disassemble the item before you return it, otherwise there will be a huge cost as oversized and it could even exceed your order amount.

Please do not purchase return labels for a damaged defective item by yourself.

If you have any problem to return the item, please contact MCombo immediately. MCombo will do its best to help you.

MCombo is not responsible for returns that the customer bought by mistake or changed their mind and other non-quality issues. However, MCombo can help customers arrange pick-up service at a reasonable price.

Note: The customer is responsible for freight costs unless the item is defective. Items returned due to being refused delivery by the customer or deemed undeliverable by freight carrier are subject to fees for a 20% restocking fee.

MCombo Customer Center

If for any reason MCombo has fallen short of your expectations or if you have any questions and suggestions, please refer to the following to contact MCombo. MCombo will do its best to work with you to make sure you are entirely satisfied.

• ? Phone: 1-323-597-1109 (Monday--Friday 8:00 a.m. -- 4:00 p.m. TIME ZONE: PST)
• ✉️ Email: sales@mcombo.com (Respond within 24 hours)
• ? Address: Newacme, 3980 Premier Ave, Memphis, TN, 38118

If there is any problem with the product, how to solve it?

In order to efficiently help solve the problem, please let MCombo know your order number, the part number of the defective/missing part, the quantity of the issue parts, and send some pictures when contacting MCombo. This information can effectively assist MCombo to solve the problem for you quickly.

Please rest assured, you will receive a reply within 24 hours.