JA-110P PET - Bus PIR Motion Detector with Basic Pet Immunity
This document is machine-translated from the original English version. In case of uncertainty or doubt, please refer to the original version of the document. If you encounter any errors or have further questions, please contact technical support (contact information can be found at the end of this document).
The JA-110P PET is a bus device in the JABLOTRON system. It is used to detect the movement of people indoors. Unlike standard PIR motion detectors from the JABLOTRON series, this detector has a modified detection characteristic and is equipped with basic pet immunity. The detector eliminates the effects of movement by small animals on the floor (animals weighing up to approx. 25 kg and a maximum height of 40 cm). The detector has a pulse reaction and occupies one position in the system. The detector must be installed by a trained technician with a valid certificate issued by an authorized distributor.
Installation
⚠️ When connecting the detector to the bus, the system must always be switched off.
- Open the detector cover by pressing the cover tab (5). Avoid touching the PIR sensor inside (11) – you may damage it.
- Remove the circuit board – it is held by a tab (3).
- Make the holes for screws and a cable in the plastic base. The recommended installation height for the detector is 2 m above the floor.
- Insert the bus cable, and attach the plastic base to the wall with screws (vertically, with the cover facing down).
- Reinsert the circuit board, and connect the cables to the terminals (8).
- Proceed by following the installation manual for the control panel.
Internal/External Parts:
- 1 - Mounting holes for a flat wall
- 2 - Mounting holes for an angle bracket (in a corner)
- 3 - PCB tab
- 4 - Mounting holes for an angle bracket (in a corner)
- 5 - Cover tab
Components:
- 6 - Red LED – activation
- 7 - Yellow LED – fault
- 8 - Bus terminals
- 9 - Production code
- 10 - Tamper sensor on the cover
- 11 - PIR sensor
System Assignment and Settings
Depending on the type of control panel, use the recommended software or application. Refer to the control panel manual.
Technical Specifications
| Specification | Value | Specification | Value |
|---|---|---|---|
| Power | From the bus 12 V (8...15 V) | Operating environment | Indoors general |
| Quiescent current consumption | 5 mA | Operating temperature range | -10 °C to +40 °C |
| Maximum current consumption | 10 mA | Average operating humidity | 75% RH, non-condensing |
| Recommended installation height | 2 m above the floor | Certification body | Trezor Test sro (No. 3025), KIWA Nederland bv |
| Detection angle/detection coverage | 90°/12 m | Also complies with | EN 50131-1, EN 50131-2-2, EN 50130-4, EN 55032, EN IEC 63000, T 031. |
| Detection angle/detection coverage - pet immunity | 90°/7 m | Recommended screw | 2x Ø 3.5 x 40 mm (countersunk head) |
| Dimensions | 60 x 98 x 52 mm | ||
| Weight | 75 g | ||
| Classification | Grade 2/II. General indoor (according to EN 50131-1) |
Compliance and Disposal
JABLOTRON a.s. hereby declares that the JA-110P PET is in compliance with the relevant EU harmonization legislation: Directive No. 2014/30/EU, 2011/65/EU, when used as intended. The original of the conformity assessment can be found at www.jablotron.com - downloads section.
Note: Proper disposal of this product will help save valuable resources and prevent potential negative effects on human health and the environment, which might otherwise arise from improper waste handling. Please return the product to the retailer, or contact your municipality for further information on the nearest collection point.
For an electronic version of this document (available in other languages) or an installation version in JA-100, please scan the attached QR code.
