JABLOTRON JA-110P PET Bus PIR Motion Detector with Basic Pet Immunity
This document is a machine translation from the Czech original. In case of any ambiguities or doubts, please refer to the original version of the document. If you encounter errors or have further questions, please contact technical support (contact details can be found at the end of this document).
The product is a component of the JABLOTRON system. It is used for motion detection of people in building interiors. Compared to standard PIR motion detectors from the JABLOTRON series, its detection characteristic is modified and it has basic immunity to animals. The detector eliminates the movement of small animals (up to approx. 25 kg and max. height 40 cm) on the floor. The detector has a pulse response and occupies one position in the system. The detector eliminates animals moving only on the floor according to its detection characteristic. It is not suitable for guarding areas where animals can move freely at heights! It is intended for installation by a trained technician with a valid Jablotron certificate.
Installation
⚠️ Connect the bus only when the system power is completely off.
- Open the detector cover (by pressing latch 5). Do not touch the PIR sensor inside (11) – it may be damaged.
- Remove the electronics using latch (3).
- Break out the openings for screws and cable in the rear plastic. The recommended detector mounting height is 2 m above the floor level.
- Thread the bus cable through and screw the rear plastic to the wall (vertically, with the cover latch facing down).
- Reattach the electronics and connect the cable to the terminals (8).
- Follow the central unit's installation manual.
Description of Product Parts
Figure 1: Description of external and internal parts of the product
- 1 – openings for mounting on a flat wall
- 2 – openings for angled mounting (corner)
- 3 – electronics board latch
- 4 – openings for angled mounting (corner)
- 5 – cover latch
- 6 – red LED – activation
- 7 – yellow LED – fault
- 8 – bus terminals
- 9 – serial number
- 10 – tamper switch
- 11 – PIR sensor
Internal Connection and Components
The detector contains an electronics board with connection terminals for the bus (CC-BUS). The terminals are labeled +U, A, GND, B. It also includes components such as a tamper switch (10) and PIR sensor (11).
Setting Properties and System Assignment
Depending on the type of central unit, use the recommended software or application, see the central unit manual.
Technical Parameters
| Power Supply | from central unit bus 12 V DC (8...15 V) | Classification | Security grade 2 / environmental class II (according to EN 50131-1) |
| Nominal current consumption | 5 mA | Environment | indoor general |
| Maximum current consumption | 10 mA | Operating temperature range | -10 °C to +40 °C |
| Recommended installation height | 2 m above floor level | Average operating humidity | 75% RH, non-condensing |
| Detection angle / detection coverage | 90° / 12 m | Certification body | Trezor Test sro (No. 3025), KIWA Nederland bv |
| PET immunity (angle / coverage) | 90° / up to 7 m | Complies with | EN 50130-4, EN 55032, EN IEC 63000, EN 50131-1, -2-2, T 031 |
| Dimensions | 60 x 98 x 52 mm | Recommended screw | 2x ⌀ 3.5 x 40 mm (countersunk head) |
| Weight | 75 g |
Declaration of Conformity and Notes
JABLOTRON a.s. declares that the product JA-110P PET is designed and manufactured in accordance with the harmonized legislative regulations of the European Union: Directive No.: 2014/30/EU, 2011/65/EU, if used according to its intended purpose. The original declaration of conformity is available at www.jablotron.com in the Downloads section.
Note: Although the product does not contain any harmful materials, do not dispose of it with household waste. Hand it over to a collection point for electronic waste. More detailed information is available at www.jablotron.com in the Downloads section.
Scan the provided QR code to access the electronic version of this document (available in other languages) or the version for installation in JA-100.
