Mcombo Wooden Dog House
User Manual
Model: 6058-DOG-1368
Brand: Mcombo
Website: mcombo.com
Description of Diagram: A line drawing of a two-level wooden dog house with a front door and ventilation grilles. The top level appears to be an open platform, while the lower level is enclosed with a door.
Product Precautions
- ? Read and follow the information in the user's manual.
- ?❌ Please keep kids away from small components to ensure safety.
- ?? Please ventilate before use.
- ?❌ Please note that the wood is not chew-proof.
- ?? Please clean up water stains and pet excrement in time.
- ⚖️ Do not place overweight items.
- ♻️ Please handle wood and other accessories properly.
Disclaimer
We ask that you read this manual completely before assembling and operating your new item. Mcombo is not responsible for any damage or injury incurred due to improper or unsafe use of the item. Mcombo specifically disclaims responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances. Please keep this manual for future reference.
Installation Preparation
- Please prepare a carpet or mat to protect your floor. You need to spread out all the accessories. Diagram Description: Two silhouetted figures stand near a pile of wooden planks and a box, suggesting preparation for assembly.
- Please prepare a pair of gloves to avoid being scratched by sharp wooden saw-dust that may occur during installation.
- Please open all the boxes to check that the accessories are complete and in good condition (Refer to Accessories List on page 4).
- The box contains some small components; please place them properly before installation to keep them away from kids and ensure safety.
- If you need to use power tools to install this product, please set the speed to low speed in advance. Due to the characteristics of wood products, the use of high speed during installation is likely to damage the wood.
Accessories List
The following parts are included in the package:
| Part Number | Description | Quantity |
|---|---|---|
| 1 | Long wooden panel (support/frame) | x 2 |
| 2 | Large flat wooden panel (top/bottom) | x 1 |
| 3 | Large flat wooden panel (base) | x 1 |
| 4 | Back panel (thin, with mounting holes) | x 1 |
| 5 | Bottom panel (with ventilation grille slots) | x 1 |
| 6 | Left side frame with hinge mounts | x 1 |
| 7 | Left door panel | x 1 |
| 8 | Right side frame with hinge mounts | x 1 |
| 9 | Wooden support dowels/bars | x 6 |
| 10 | Right door panel | x 1 |
| 11 | Ventilation grille | x 2 |
Hardware List
The following hardware is included:
| Code | Description | Dimensions/Details | Quantity |
|---|---|---|---|
| A | Screw | 6 x 35mm | 3+1 |
| B | Cam Lock | Φ 15 x 10 | 3+1 |
| C | Screw | 8 x 30mm | 4+1 |
| D | Screw | 6 x 30mm | 4+1 |
| E | Screw | 7 x 47mm | 8+1 |
| F | Allen Wrench | M4 x 55 | 1 |
| G | Screw | 3.5 x 14mm | 10+1 |
| H | Screw | 4 x 35mm | 5+1 |
| I | Screw | M6*12 | 12+1 |
| J | Screw | M6 x12mm | 4+1 |
| K | Screw | M6 x 25mm | 12+1 |
| L | Screw | M6 x 35mm | 12+1 |
| M | Wooden Dowel/Connector | 46 * 16 * 14mm | 2 |
| N | Door Handle | 131 * 20 * 23mm | 3 |
| O | Screw | M4 * 18mm | 6+1 |
| P | Screw | M6 x Φ 23 | 4 |
| Q | Bracket | 32 * 12 * 10 | 2 |
| R | Circular Pads | Φ 20 | 1 |
| S | Anti-fall Strap | 180 * 20mm | 2 |
| T | Screw | Φ 8 x 40mm | 2 |
Installation Instructions
Step 1
Please note: Hardware 'A' needs to be fully tightened.
Diagram Description: Attaching hardware to panel 3. Use screws 'A' (x3), 'G' (x4), and connectors 'M' (x2). Panel 3 is shown flat. Screws 'A' are inserted through holes, and cam locks 'G' are used with connectors 'M'.
Hardware Used: A (x3), G (x4), M (x2)
Parts Used: 3 (x1)
Step 2
Connecting wooden support bars (9) to panels 2 and 3 using screws 'K' (x8). Panel 2 and panel 3 are shown being assembled with horizontal bars.
Hardware Used: K (x8), F (Allen Wrench x1)
Parts Used: 2 (x1), 3 (x1), 9 (x4)
Step 3
Attaching panels 1 (x2) to the structure using screws 'C' (x4).
Hardware Used: C (x4)
Parts Used: 1 (x2)
Step 4
Securing panels 1 (x2) to panels 2 and 3 using screws 'E' (x4). The Allen wrench 'F' is used.
Hardware Used: E (x4), F (Allen Wrench x1)
Parts Used: 1 (x2), 2 (x1), 3 (x1)
Step 5
Attaching wooden support bars (9) to panel 5 using screws 'K' (x4). Panel 5 is shown flat.
Hardware Used: K (x4), F (Allen Wrench x1)
Parts Used: 5 (x1), 9 (x2)
Step 6
Connecting panel 4 (back panel) to panel 3 using screws 'D' (x2).
Hardware Used: D (x2)
Parts Used: 3 (x1), 4 (x1)
Step 7
How to use it?
Attaching cam locks 'B' (x3) to panels 3 and 4. The diagram shows inserting the cam lock into a pre-drilled hole and then turning it to secure.
Hardware Used: B (x3)
Parts Used: 3 (x1), 4 (x1)
Step 8
Connecting panel 5 to panels 3 and 4 using screws 'D' (x2).
Hardware Used: D (x2)
Parts Used: 3 (x1), 4 (x1), 5 (x1)
Step 9
Attaching panel 5 to panel 4 using screws 'H' (x3).
Hardware Used: H (x3)
Parts Used: 4 (x1), 5 (x1)
Step 10
PLEASE NOTE: The doors could be freely exchanged as you wish.
Option 1: Install the door on the left.
Attach left door panel (7) using screws 'E' (x2) and 'L' (x6). Connect frame 6 (x1).
Hardware Used: E (x2), L (x6), F (Allen Wrench x1)
Parts Used: 2 (x1), 3 (x1), 5 (x1), 6 (x1), 7 (x1)
Option 2: Install the door on the right.
Attach right door panel (10) using screws 'E' (x2) and 'L' (x6). Connect frame 8 (x1).
Hardware Used: E (x2), L (x6), F (Allen Wrench x1)
Parts Used: 2 (x1), 3 (x1), 5 (x1), 8 (x1), 10 (x1)
Diagram Description: Shows two assembly options for attaching doors to the main structure. One uses frame 6 and door 7 on the left, the other uses frame 8 and door 10 on the right. Screws E and L are used for attachment.
Step 11
PLEASE NOTE: The doors could be freely exchanged as you wish.
Option 1: Install the door on the left.
Attach door panel (8) to the frame using screws 'P' (x4) and 'L' (x6). Use screws 'E' (x2).
Hardware Used: E (x2), L (x6), P (x4), F (Allen Wrench x1)
Parts Used: 6 (x1), 8 (x1)
Option 2: Install the door on the right.
Attach door panel (6) to the frame using screws 'P' (x4) and 'L' (x6). Use screws 'E' (x2).
Hardware Used: E (x2), L (x6), P (x4), F (Allen Wrench x1)
Parts Used: 8 (x1), 6 (x1)
Diagram Description: Shows two assembly options for attaching the doors to the side frames. Screws E, L, and P are used. The diagram illustrates attaching the door panel to the corresponding side frame.
Step 12
Attach door handle 'N' (x1) to door panel 7 using screws 'O' (x2). Attach ventilation grille (11) using screws 'O' (x2).
Hardware Used: N (x1), O (x2)
Parts Used: 7 (x1)
Diagram Description: Shows attaching a handle (N) to door panel 7 and a ventilation grille (11) to the bottom of the door panel using screws O.
Step 13
Attach door handle 'N' (x2) to door panel 10 using screws 'O' (x4). Attach ventilation grille (11) using screws 'O' (x4).
Hardware Used: N (x2), O (x4)
Parts Used: 10 (x1)
Diagram Description: Shows attaching two handles (N) to door panel 10 and two ventilation grilles (11) to the bottom of the door panel using screws O. Note: The diagram shows 'X2' indicating this step is for both doors, but the quantities are listed per door.
Step 14
PLEASE NOTE: Tighten the 'I' screws first, then fasten the 'I' screws.
Option 1: Attach door panel 7 to the main structure. Use screws 'I' (x4) and circular pads 'R' (x1).
Hardware Used: I (x4), R (x1)
Parts Used: 7 (x1)
Option 2: Attach door panel 10 to the main structure. Use screws 'I' (x4) and circular pads 'R' (x1).
Hardware Used: I (x4), R (x1)
Parts Used: 10 (x1)
Diagram Description: Shows attaching the door panels (7 or 10) to the main body of the dog house using screws 'I' and circular pads 'R'. The diagram indicates two possible attachment points for the door.
Step 15
PLEASE NOTE: Tight the '#I' screws first, after placing the door bolt in the correct position, then fasten the '#I' screws.
Attach brackets 'Q' (x2) and screws 'G' (x4) to secure the door hinges. Use screws 'I' (x8) to attach the door panels to the frame.
Hardware Used: G (x4), I (x8), Q (x2)
Parts Used: 10 (x1)
Diagram Description: Shows attaching brackets 'Q' with screws 'G' near the door hinges, and then securing the door panel (10) to the frame with screws 'I'.
Step 16
Attach ventilation grilles (11) to the bottom of the door panels using screws 'J' (x4).
Hardware Used: J (x4)
Parts Used: 11 (x2)
Diagram Description: Shows attaching the ventilation grilles (11) to the bottom of the door panels using screws 'J'.
Step 17
Please note: # S is an anti-falling part, please install it as much as possible for safety.
Attach anti-fall straps 'S' (x2) to the top of the dog house. Use screws 'G' (x2) to secure them.
Hardware Used: G (x2), S (x2)
Diagram Description: Shows attaching anti-fall straps 'S' to the top edges of the dog house structure using screws 'G'.
Step 18
Please note: More stable to attach the crate to the wall.
Attach the dog house to a wall using screws 'T' (x2) and 'H' (x2). The diagram shows wall anchors being used.
Hardware Used: T (x2), H (x2)
Diagram Description: Shows the dog house positioned near a wall, with screws 'T' and 'H' being used to secure it to the wall, likely via brackets or pre-drilled holes on the dog house.
Warranty
| Item | Duration |
|---|---|
| Wood | 1 Year |
| Hardware | 6 Months |
Limitations Applicable to All Warranties
All warranties begin on the date of delivery. All warranties are to the original purchaser from MCOMBO /EXACME ONLY.
Warranty Detail Explanation
- Mcombo will replace the defective parts or send a replacement item provided that the warranty parts have not been subjected to misuse, abuse, or improper service by the consumer, for example, damaged part arising in.
- Exclusions also include components with damage caused by:
- Contamination
- Abuse, misuse, accident or negligence
- Commercial use, or use other than normal
- Improper operation maintenance, or storage
- Mcombo will pay standard shipping rates on all warranted parts for the first year. Mcombo can also sell you the replacement part for a discount price when your item is out of warranty policy.
Return/Replacement Policy
MCOMBO: All items come with a 30-day return/replace policy. During this time, Mcombo will cover the shipping cost of return and replacement for a defective and damaged item, and provide pre-paid return labels or pick-up service.
Note: Please disassemble the item before you return it, otherwise there will be a huge cost as oversized and it could even exceed your order amount.
Important: Please do not purchase return labels for a damaged defective item by yourself.
If you have any problem to return the item, please contact Mcombo immediately; they will do their best to help you.
Mcombo is not responsible for the returns that the customer bought by mistake or changed their mind and other non-quality issues. However, Mcombo can help customers to return the items.
Note: The customer is responsible for freight costs unless the item is defective. Items returned due to being refused delivery by the customer or deemed undeliverable by freight carrier are subject to fees for a 20% re-stocking fee.
MCOMBO Customer Center
If for any reason Mcombo has fallen short of your expectations, or if you have any questions and suggestions, please refer to the following to contact Mcombo. They will do their best to work with you to make sure you are entirely satisfied.
| ? | 1-323-597-1109 (Monday--Friday AM 9:00--PM 17:00) |
| ✉️ | sales@mcombo.com (Respond within 24 hours) |
| ? | Newacme 3980 Premier Ave Memphis, TN, 38118 |
If there is any problem with the product, how to solve it?
In order to efficiently help Mcombo solve the problem, please let them know your order number, the part number of the defective/missing part, the quantity of the issue parts, and send some pictures when contacting them. This information can effectively assist them to solve the problem for you quickly.
Please rest assured, you will receive a reply within 24 hours.
