MCombo Wooden Dog Crate Furniture

Product Precautions

• [info-symbol] Read and follow the information in the user's manual.
• [safety-symbol] Please keep children away from small components to ensure safety.
• [ventilation-symbol] Please ventilate before use.
• [weight-limit] Do not place overweight items.
• [warning-symbol] Please note that the wood is not chew-proof.
• [cleaning-symbol] Please clean up water stains and pet excrement in time.
• [handling-symbol] Please handle wood and other accessories properly.

Disclaimer

Read this manual completely before assembling and operating your new item. Mcombo is not responsible for any damage or injury incurred due to improper or unsafe use of the item. Mcombo specifically disclaims responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances. Please keep this manual for future reference.

Installation Preparation

1. Prepare a carpet or mat to protect your floor. Spread out all accessories.
2. Prepare a pair of gloves to avoid being scratched by sharp wooden sawdust that may occur during installation.
3. Open all boxes to check that accessories are complete and in good condition (refer to Accessories List on page 4).
4. The box contains small components; place them properly before installation to keep them away from children and ensure safety.
5. If using power tools, set the speed to low in advance. High speed may damage the wood.

Assembly Instructions

General Notes for Assembly

• Please check the quantity of all parts before installing the product.
• Please do not tighten the screws before completing all the installation steps.
• Question: Is there any broken or missing part? Answer: If yes, please feel free to contact us (see page 25), we will do our best to assist you to solve the problem as soon as possible.

Parts List

Main Components:

• Part 1: 955*741mm
• Part 2: 140*20mm
• Part 3: 955*250mm
• Part 4: 991*529mm
• Part 5: 955*741mm
• Part 6: 955*250mm
• Part 7: 991*529mm
• Part 8: 991*565mm
• Part 9: 991*565mm
• Part 10: 991*565mm
• Part 11: 901*561mm
• Part 12: 902*562mm
• Part 13: 585*34mm
• Part 14: 424*178mm
• Part 15: 438*136mm
• Part 16: 391*136mm
• Part 17: 418*401mm
• Part 18: 561*501mm
• Part 19: 563*500mm
• Part 20: 975*635mm
• Part 21: 535*635mm
• Part 22: 560*20mm
• Part 23: 560*25mm

Hardware List:

• A: 3.5*60mm (5+2PCS)
• B: 3.5*45mm (29+2PCS)
• C: 3.5*40mm (9+2PCS)
• D: 3.0*38mm (10+2PCS)
• E: 3.0*30mm (16+2PCS)
• F: 3.5*20mm (12+2PCS)
• G: 3.0*16mm (40+2PCS)
• H: 3.0*14mm (12+2PCS)
• I: Dowels/Connectors (26+2PCS)
• J: Screws/Fasteners (8+1PCS)
• K: Brackets/Connectors (4PCS)
• L: Brackets/Connectors (2PCS)
• M: Drawer Slides/Brackets (2PCS)
• N: Bracket (1PCS)
• O: Knobs/Similar (8+2PCS)
• P: Hinges/Similar (3PCS)
• Q: Brackets/Connectors (4PCS)

Step 1

Attach part M (x6) to the main frame (part 1) using screws G (x12). Attach part K (x2) to the back of part 1. Attach part M (x2) to the sides of part 1.

Step 2

Attach part N (x1) to the bottom of part 1 using screws H (x4).

Step 3

Attach part D (x2) using screws I (x2) to part 2.

Step 4

Attach parts 8, 9, and 10 to the main structure using screws I (x2 each) and I (x12).

Step 5

Attach part 8 to the main frame (part 1) using screws B (x3). Attach part 9 to the main frame using screws B (x3).

Step 6

Attach part 5 (a slatted panel) to the main frame using screws B (x6).

Step 7

Attach part 6 (a slatted panel) to the main frame using screws B (x2) on each side.

Step 8

Attach part 3 (a horizontal support) to the main frame using screws A (x2).

Step 9

Place part 12 (the top panel) onto the assembled structure.

Step 10

Secure the top panel (part 12) by screwing G (x3) into the designated holes on each side.

Step 11

Attach part 13 (a horizontal support) to the top of the main frame using screws B (x2) on each side.

Step 12

Attach part B (x1) to the front of the unit (likely a drawer front or similar).

Step 13

Attach parts 22 (x2) and 23 (x2) using screws I (x2 each) and I (x2) to the sides of the unit.

Step 14

Attach part 4 (a side panel) to the unit using screws B (x4). Attach part 7 (a slatted panel) to the unit using screws B (x3).

Step 15

Attach part 4 (a side panel) to the unit using screws A (x3). Attach part 10 (a slatted panel) to the unit using screws A (x3).

Step 16

Attach drawer handles (part P, x3) to the drawer fronts (part F, x12) using screws F (x4 each).

Step 17

Assemble the drawer box. Attach parts 15 (x4) and 16 (x2) to part 14 (x2) using screws E (x2 each). Attach part 17 (x2) to the front of the drawer using screws J (x2). Attach part K (x2) to the sides. Repeat this step twice for two drawers.

Step 18

Attach the assembled drawer front (part 14) to the drawer box using screws E (x2 on each side). Repeat this step twice.

Step 19

Insert the two assembled drawers into the main unit.

Step 20

Secure the bottom panel (part 12) by screwing G (x16) into the designated holes from the bottom.

Step 21

Attach parts L (x2) using screws H (x2) to part Q (x4). Then attach these assemblies to the main unit using screws H (x8).

Step 22

Insert shelves (part 11, x1) into the designated slots. Insert shelves (part 18, x2) into the designated slots.

Step 23

Attach parts 19 (x2) to the unit using screws O (x8).

Step 24

Prepare parts 22 (x2) and 23 (x2) by attaching them using screws I (x2 each) and I (x2).

Step 25

Attach the prepared parts 23 (x2) and 20 (x1) to part 22 (x1) using screws D (x4).

Step 26

Place the assembled section (from Step 25) onto the main unit and secure it using screws C (x3) on each side.

Step 27

Attach the prepared parts 23 (x2) and 21 (x1) to part 22 (x1) using screws D (x4).

Step 28

Place the assembled section (from Step 27) onto the main unit and secure it using screws C (x3).

Warranty Information

Warranty Period

Limitations Applicable to All Warranties

All warranties begin on the date of delivery. All warranties are to the original purchaser from Mcombo/EXACME ONLY.

Warranty Detail Explanation

Mcombo will replace defective parts or send a replacement item provided that the warranty parts have not been subjected to misuse, abuse, or improper service by the consumer, for example, damaged part arising inconsequence of negligence or improper operation.

Exclusions

• Contamination
• Abuse, misuse, accident, or negligence
• Commercial use, or use other than normal
• Improper operation, maintenance, or storage

Mcombo will pay standard shipping rates on all warranted parts for the first year. Replacement parts outside the warranty period can be purchased at a discount.

Return/Replacement Policy

Mcombo offers a 30-day return/replace policy. Shipping costs for defective or damaged items are covered, with pre-paid return labels or pick-up service provided for customer convenience.

Note: Please disassemble the item before returning to avoid oversized shipping costs. Do not purchase return labels for damaged defective items yourself.

Mcombo is not responsible for returns due to customer mistake or change of mind, but can arrange pick-up service at a reasonable price.

Note: The customer is responsible for freight costs unless items are defective and returned due to refused delivery or being undeliverable, which may incur a 20% restocking fee.

Mcombo Customer Center

For any questions or suggestions, please contact Mcombo. We strive to ensure you are entirely satisfied.

Troubleshooting

To efficiently resolve product issues, please provide your order number, the part number of the defective/missing part, the quantity of the issue parts, and send pictures when contacting us. A reply will be provided within 24 hours.