MCombo Wooden Dog House

Product Precautions

• 💬 Read and follow the information in the user's manual.
• 🛡 Please keep children away from small components to ensure safety.
• 🏦☁ Please ventilate before use.
• ⚠️ Please note that the wood is not chew-proof.
• 💧🐶 Please clean up water stains and pet excrement in time.
• 🔲 Do not place overweight items.
• 👇👆 Please handle wood and other accessories properly.

Disclaimer

We ask that you read this manual completely before assembling and operating your new item. Mcombo is not responsible for any damage or injury incurred due to improper or unsafe use of the item. Mcombo specifically disclaims responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances. Please keep this manual for future reference.

Installation Preparation

1. Please prepare a carpet or mat to protect your floor. You need to spread out all the accessories.
2. Please prepare a pair of gloves to avoid being scratched by sharp wooden sawdust that may occur during installation.
3. Please open all the boxes to check that the accessories are complete and in good condition (Refer to the accessories list on page 4).
4. The box contains some small components; please place them properly before installation to keep them away from children and ensure safety.
5. If you need to use power tools to install this product, please set the speed to low speed in advance. Due to the characteristics of wood products, the use of high speed during installation is likely to damage the wood.

Accessories List

The following parts are included in the package:

Kindly Note:

• Please check the quantity of all parts before installing the product.
• Please do not tighten the screws before completing all the installation steps.

Q: Is there any broken or missing part?

A: If yes, please feel free to contact Mcombo customer service (see page 21). Mcombo will do its best to assist you to solve the problem as soon as possible.

Hardware List

Installation Instructions

1. Step 1

   Attach side panels (5, 6) to the base panel (1). Use screws (A x8), cam locks (J x1), screws (M x4), and screws (Q x1). Ensure cam locks (J) are inserted into their designated holes and turned to secure. Ensure screws (A) are fully tightened as indicated.

   Parts used: 1, 5, 6. Hardware used: A (x8), J (x1), M (x4), Q (x1).

2. Step 2

   Attach back panels (7, 8) to the base panel (1). Use screws (A x2). The OCR indicated '5x1' which might be a typo; assuming it means attaching panels 7 and 8 to the base (1) using screws A.

   Parts used: 1, 7, 8. Hardware used: A (x2).

3. Step 3

   Attach side panel (6) to the base panel (5). Use dowels (C x2) and screws (C x1). Insert dowels (C) into the pre-drilled holes on panel 5 and then align panel 6. Secure with screws (C).

   Parts used: 5, 6. Hardware used: C (x2), C (x1).

4. Step 4

   Prepare to attach cam locks (B x2) to the side panel (6). The diagram shows how to insert and orient the cam lock (B) into the panel.

   Parts used: 6. Hardware used: B (x2).

5. Step 5

   Attach side panels (5, 6) to the base panel (1). Use cam locks (B x4). Insert the cam locks into the corresponding holes on the base panel (1) and turn them to secure the side panels (5, 6) which have the cam studs.

   Parts used: 1, 5, 6. Hardware used: B (x4).

6. Step 6

   Attach front door panels (3, 4) to the assembled structure. Use dowels (C x2) and screws (C x1). Insert dowels (C) into the bottom edge of panels 3 and 4, then align them with the base panel (1). Secure with screws (C).

   Parts used: 1, 3, 4. Hardware used: C (x2).

7. Step 7

   Attach front door panels (3, 4) to the structure. Use cam locks (B x4). Insert cam locks (B) into the base panel (1) and turn to secure the front panels (3, 4) which have cam studs.

   Parts used: 1, 3, 4. Hardware used: B (x4).

8. Step 8

   Attach back panels (7, 8) to the assembled structure. Use screws (8 x1) and screws (7 x1). Align panels 7 and 8 with the side panels (5, 6) and secure them to the base (1) and side panels.

   Parts used: 7, 8. Hardware used: 8 (x1), 7 (x1).

9. Step 9

   Attach the top panel (2) to the structure. Use screws (D x8), screws (M x2), cam locks (Q x1), and dowels (C x2). Insert dowels (C) and cam studs into the top edges of the side and back panels. Place the top panel (2) on top, aligning the holes. Secure with cam locks (Q) and screws (D, M).

   Parts used: 2. Hardware used: C (x2), D (x8), M (x2), Q (x1).

10. Step 10

    Attach floor pads (L x5) to the underside of the base panel (1). Peel off the backing and stick them to the designated areas.

    Parts used: 1. Hardware used: L (x5).

11. Step 11

    Attach the top frame (13) to the top of the structure. Use screws (E x2). Align the top frame (13) with the top edges of the side panels and secure with screws (E).

    Parts used: 13. Hardware used: E (x2).

12. Step 12

    Attach shelf supports (11) to the inner sides of the structure. Use screws (D x2) for each support. Align the shelf supports (11) with the pre-drilled holes on the side panels and secure with screws (D).

    Parts used: 11 (x2). Hardware used: D (x8).

13. Step 13

    Attach side frame (14) to the structure. Use screws (E x2). Align side frame (14) with the top frame (13) and side panel, and secure with screws (E).

    Parts used: 14. Hardware used: E (x2).

14. Step 14

    Attach side frame (14) to the structure. Use screws (E x2). Align side frame (14) with the top frame (13) and side panel, and secure with screws (E).

    Parts used: 14. Hardware used: E (x2).

15. Step 15

    Attach shelves (12) to the shelf supports (11). Use screws (D x2) for each shelf. Align the shelves (12) with the supports (11) and secure with screws (D).

    Parts used: 12 (x2). Hardware used: D (x8).

16. Step 16

    Attach brackets (P x2) to the front door panel (9). Use screws (M x8). Align brackets (P) with the pre-drilled holes on the inside of the door panel (9) and secure with screws (M).

    Parts used: 9. Hardware used: M (x8), P (x2).

17. Step 17

    Attach hinge (R x1) and handle (H x1) to the front door panel (9). Use screws (G x2) for the hinge and screws (M x2) for the handle. Align the hinge (R) and handle (H) with the pre-drilled holes on the door panel (9) and secure them.

    Parts used: 9. Hardware used: G (x2), H (x1), M (x2), R (x1).

18. Step 18

    Attach the front door panel (9) to the main structure. Use screws (M x2) on each side. Align the hinge (R) on the door panel with the corresponding holes on the side panel (5 or 6) and secure with screws (M).

    Parts used: 9. Hardware used: M (x4).

19. Step 19

    Attach top frame elements (F, N) to the top of the structure. Use screws (F x8) and screws (N x8). Align the frame pieces with the top edges of the side and back panels and secure them using the specified screws.

    Parts used: None explicitly shown, but attaches to structure. Hardware used: F (x8), N (x8).

20. Step 20

    Place the shelves (10 x2) onto the shelf supports (11). The diagram indicates placing the shelves on the supports.

    Parts used: 10 (x2).

21. Step 21

    For increased stability, attach the unit to the wall using the provided wall anchor hardware (O x2, K x2, S x2). Follow the diagram to install the anchors securely into the wall and the unit.

    Hardware used: K (x2), O (x2), S (x2).

Warranty

Limitations Applicable to All Warranties

All warranties begin on the date of delivery.

All warranties are to the original purchaser from Mcombo / ExacMe ONLY.

Warranty Detail Explanation

• Mcombo will replace defective parts or send a replacement item provided that the warranty parts have not been subjected to misuse, abuse, or improper service by the consumer, for example, damaged part arising as a consequence of negligence or improper operation.
• Exclusions also include components with damage caused by:
  • Contamination
  • Abuse, misuse, accident, or negligence
  • Commercial use, or use other than normal
  • Improper operation, maintenance, or storage
• Mcombo will pay standard shipping rates on all warranted parts for the first year. Mcombo can also sell replacement parts at a discount price when an item is out of warranty policy.

Return/Replacement Policy

Mcombo: All items come with a 30-day return/replace policy. During this time, Mcombo will cover the shipping cost of return and replacement for a defective and damaged item, and provide a pre-paid return label or pick-up service for customer's convenience.

Note: Please disassemble the item before you return it, otherwise there will be a huge cost for oversized items, which could even exceed your order amount.

Note: Please do not purchase return labels for a damaged defective item by yourself.

If you have any problem returning the item, please contact Mcombo immediately. Mcombo will do its best to help you.

Mcombo is not responsible for returns due to customer mistake or change of mind, and other non-quality issues. However, Mcombo can help customers arrange pick-up service at a reasonable price.

Note: The customer is responsible for freight costs unless the item is defective. Items returned due to being refused delivery by the customer or deemed undeliverable by freight carrier are subject to fees for a 20% restocking fee.

Mcombo Customer Center

If for any reason Mcombo has fallen short of your expectations, or if you have any questions and suggestions, please refer to the following contact information. Mcombo will do its best to work with you to ensure you are entirely satisfied.

• Phone: 1-323-597-1109 (Monday-Friday 8:00 a.m. - 4:00 p.m. PST)
• Email: sales@mcombo.com (Respond within 24 hours)
• Address: Newacme, 3980 Premier Ave, Memphis, TN, 38118

If there is any problem with the product, how to solve it?

To efficiently help solve the problem, please provide your order number, the part number of the defective/missing part, the quantity of the issue parts, and send pictures when contacting Mcombo. This information will effectively assist in solving the problem quickly.

Please rest assured, you will receive a reply within 24 hours.