Item Number: 6918867
WARNING
To reduce the risk of fire, electric shock, or personal injury:
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16" should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is LED, 7W.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
Image for Finished Product
[Description of finished product image: A decorative wall light with an intricate, swirling pattern design.]
Tools Required (Not Included)
Before starting assembly and installation, please prepare the needed tools as below:
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included
- (C) Mounting plate (1)
- (D) Green ground screw (1)
- (E) Back plate (1)
- (F) Screw (2)
- (G) Glass (1)
- (H) Nut (2)
- (I) Base (1)
Accessories Enclosed
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
Assembly & Installation Instructions
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the illustration.
- Turn off power. Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Make assembly:
- Step A1: Unscrew screws (F) from back plate (E) and mounting plate (C), then set them aside for later installation.
- Step A2: Carefully pass the supply wires from the outlet box through mounting plate (C). Secure mounting plate (C) to the outlet box with mounting screws (A).
- Step A3: Make wire connections. Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect Ground Wires
[Diagram description: Shows two methods (A and B) for connecting ground wires, illustrating the outlet box ground and fixture ground connection points.]
Connect Supply Wires
Supply Wire (Black/Red) Supply Wire (White) Fixture Wire Black White Black *Parallel cord (round & smooth) *Parallel cord (square & ridged) White Clear, Brown, Gold or Black without tracer Clear, Brown, Gold or Black with tracer Black Insulated wire(other than green) with copper conductor Insulated wire(other than green) with silver conductor White * Note: When parallel wires (SPT I& SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Step A4: Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (C) with the previously removed screws (F). Hand tighten until snug.
NOTE: back plate (E) should be snug against the wall with screws (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (C):
- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled mounting screws in or out of mounting plate (C).
- When the secure length is achieved, tighten the pre-assembled hex nuts and return to Step A4.
- Step A5: Insert glass (G) into base (I), and then screw nuts (H) to holes to secure the body in place as shown in the illustration.
- Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!
Ordering Parts
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
Cleaning
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
