Item Number: Z-09BZBMEU-5394

Safety Warnings

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save them for future reference.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse or circuit breaker box in your home.
   • Place the main power switch in the "OFF" position.
   • Place the wall switch in the "OFF" position.
4. Mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16" should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type T, Max 60W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damage to the lamp's surface.
8. When replacing bulbs, turn off or unplug the lamp and wait until it is cool, as bulbs get hot quickly.
9. The safety instructions in this manual are not meant to cover all possible conditions. Common sense, caution, and care must be used with any electrical products.

Finished Product

The finished product is a decorative lighting fixture, likely a chandelier or pendant light, featuring multiple arms and decorative frames.

Tools Required (Not Included)

• Ladder: For safe access to the installation area.
• Philips Head or Flat Blade Screwdriver: For securing screws during assembly.
• Electrical Tape: For insulating and securing wire connections.
• Pliers: For gripping, bending, or cutting wires and parts.
• Wire Cutter/Stripper: For cutting wires to length and stripping insulation.

Parts Type & Quantity Included

• (C) Mounting plate (1)
• (D) Green ground screw (1)
• (E) Canopy (1)
• (F) Swivel joint (1)
• (G) Canopy nut (2)
• (H) Tube (for height adjustment)
• (I) Connector (1)
• (J) Connector pipe (1)
• (K) Lamp base adapter (1)
• (L) Black iron frame (4)
• (M) Gold iron frame (4)

Accessories & Quantity Enclosed

• (A) Plastic wire connector (3)
• (B) Mounting screw (2)

Assembly & Installation Instructions

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the illustration.
2. Turn off power: Before starting installation, ensure electricity is shut off at the main fuse or circuit breaker and the wall switch is in the "OFF" position.
3. Unscrew canopy nuts (G) from canopy (E). Remove the mounting plate (C). This involves detaching the canopy from the ceiling mount.
4. Pass the fixture wires through the connector pipe (J) and connector (I). Screw the lamp base adapter (K) onto the connector pipe (J). Insert the connector pipe (J) into the connector (I). This step connects the main body of the fixture to the hanging mechanism.
5. Adjust the black iron frames (L) and gold iron frames (M) to achieve the proper angle, following the provided illustration.
6. Select and use tubes (H) to achieve the desired hanging height. Pass the fixture wires through the chosen tubes (H), the swivel joint (F), and the canopy (E). Ensure all threaded tubes are tightened, then screw the chosen tubes (H) onto the swivel joint (F) and the top of connector (I). Hand tighten until snug.
7. Attach the mounting plate (C) to the outlet box using the mounting screws (B). This secures the fixture's electrical connection point to the ceiling.
8. Make wire connections:

   IMPORTANT: The ground wire is bare copper wire. NEVER connect other wires to ground wires.

   Connect Black or Red Supply Wire to:	Connect White Supply Wire to:	Ground Wire Connection
   Black	White	Connect fixture ground wire (bare copper) to the outlet box ground screw (green).
   Clear, Brown, Gold or Black without tracer (typically parallel cord, round & smooth)	Clear, Brown, Gold or Black with tracer (typically parallel cord, square & ridged)	Ensure the ground wire is securely attached to the green ground screw on the mounting plate or outlet box.
   Insulated wire (other than green) with copper conductor	Insulated wire (other than green) with silver conductor

   Note on Parallel Wires: When using parallel wires (SPT I & SPT II), the neutral wire is typically square-shaped or ridged, while the hot wire is round or smooth.

   • Twist wires together using the plastic wire connectors (A) until tightly joined.
   • Wrap each connector with approved electrical tape for added security.
   • Ensure no wire strands are exposed and carefully tuck all wires into the outlet box.
9. Raise the canopy (E) to the ceiling and secure it in place by tightening the canopy nuts (G) onto the pre-assembled screws in the mounting plate (C).
   • Note: The canopy (E) should be snug against the ceiling. If not, adjust the threaded length on the mounting plate (C) by unscrewing or screwing the pre-assembled screws in or out of the mounting plate (C). Once the correct length is achieved, tighten the hex nuts and return to this step.
10. Install bulbs (not included). Please do not exceed the maximum wattage recommended on the socket.
11. Check that everything is installed properly, then you can turn on the light.

Ordering Parts

Keep this sheet for future reference if you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use the exact wording from the illustration when ordering parts.

Cleaning

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads, powders, steel wool, or abrasive paper.