Short Closet Rods Closet with Open Drawers Assembly Instructions

Part List

Hardware List

How to Install Camlocks

Step 1: Connect the male camlock as directed in the assembly instructions with a screwdriver. [Diagram shows male camlock being screwed into a panel, with text 'DO NOT OVER TIGHTEN']

Step 2: Put the male camlock into the entry hole. [Diagram shows male camlock inserted into a hole on another panel]

Step 3: Insert the female camlock as shown in the instruction. Note: ensure that the arrow on the top of the camlock points toward the entry hole for the male camlock. [Diagram shows female camlock being inserted, with arrow detail]

Step 4: Screw the female camlock clockwise with a screwdriver. You will feel a click when the camlock is locked in place. The camlock is now completed. [Diagram shows screwdriver turning female camlock]

Assembly Steps

Step 1

Assemble drawer base. Attach U to T using four (17) screws. Attach S to T using two (17) screws. Attach W to the assembly using four (17) screws. [Diagram shows parts T, U, S, W being joined. An arrow indicates the orientation for part W.]

Step 2

Attach drawer front. Attach V to U and S using four (1) screws. [Diagram shows part V being attached to the front of the partially assembled drawer.]

Step 3

Attach drawer sides to front. Attach U and S to V using four (2) cam lock nuts. [Diagram shows drawer sides U and S being attached to drawer front V.]

Step 4

Attach drawer slides. Attach drawer slides (14) and (16) to the drawer sides U and S using six (6) screws. Attach drawer slide (14) to the drawer side U using one (14) screw. Attach drawer slide (16) to the drawer side S using one (16) screw. [Diagram shows drawer slides being attached to the exterior of the drawer sides.] Note: 'Roller end' is indicated.

Step 5

Assemble second drawer base. Attach BB to T using four (17) screws. Attach AA to T using two (17) screws. Attach W to the assembly using four (17) screws. [Diagram shows parts T, BB, AA, W being assembled.]

Step 6

Attach drawer back. Attach CC to BB and AA using four (1) screws. [Diagram shows part CC being attached to the back of the partially assembled drawer.]

Step 7

Attach drawer sides to back. Attach BB and AA to CC using four (2) cam lock nuts. [Diagram shows drawer sides BB and AA being attached to drawer back CC.]

Step 8

Attach drawer slides. Attach drawer slides (14) and (16) to the drawer sides AA and BB using six (6) screws. Attach drawer slide (14) to the drawer side AA using one (14) screw. Attach drawer slide (16) to the drawer side BB using one (16) screw. [Diagram shows drawer slides being attached to the exterior of the drawer sides.] Note: 'Roller end' is indicated.

Step 9

Attach drawer bottom to front. Attach CC to D using two (4) screws. Attach CC to P using one (12) rod. [Diagram shows part CC being attached to the front panel D and P.]

Step 10

Attach side panels to base. Attach Z to I using eighteen (6) screws. Attach Z to D using three (13) shelf supports. Attach I to D using three (15) shelf supports. [Diagram shows side panels Z and I being attached to the base panel D.] Note: 'Roller is at bottom' is indicated. Close-up shows roller detail.

Step 11

Attach shelf panels. Attach D to C using fourteen (1) screws. [Diagram shows panel D being attached to panel C.]

Step 12

Attach drawer runners to base. Attach R to D using four (2) cam lock nuts. [Diagram shows parts R being attached to panel D.] Note: 'Keep the holes of the Part R toward this direction as shown'.

Step 13

Attach front panel to base. Attach D to Q using two (1) screws. [Diagram shows panel D being attached to panel Q.]

Step 14

Attach divider panel. Attach P to D using two (2) cam lock nuts. [Diagram shows panel P being attached to panel D.]

Step 15

Attach side panel. Attach Z to N using four (1) screws. [Diagram shows panel Z being attached to panel N.]

Step 16

Attach side panels to base. Attach M and N to Z using four (2) cam lock nuts. [Diagram shows panels M and N being attached to panel Z.] Note: 'Keep the holes of the Part M and Part N toward this direction as shown'.

Step 17

Attach shelf supports. Attach Q and F to Z using six (3) screws. [Diagram shows panels Q and F being attached to panel Z.]

Step 18

Attach front panel to side. Attach D to Z using two (3) screws. [Diagram shows panel D being attached to panel Z.] Note: 'Keep the holes of the Part D toward this direction as shown'.

Step 19

Attach divider panel. Attach P to Z using two (3) screws. [Diagram shows panel P being attached to panel Z.]

Step 20

Insert drawer runners. Insert O panels into the assembly. [Diagram shows panels O being slid into place.] Note: Close-up shows part (19) (handle) being attached to O.

Step 21

Attach back panels and shelf supports. Attach M, I, F, Q, D, R to the structure using fourteen (3) screws. [Diagram shows multiple panels being attached to the main frame.]

Step 22

Attach side panels and drawer slides. Attach N, R, D, P to the structure using ten (3) screws. [Diagram shows panels N, R, D, P being attached.]

Step 23

Attach top panel. Attach C to M, Z, N, J using ten (2) cam lock nuts. [Diagram shows top panel C being attached to the main structure.] Close-up shows cam lock detail.

Step 24

Attach side panel. Attach Y to I using four (1) screws. [Diagram shows panel Y being attached to panel I.]

Step 25

Attach side panel. Attach Y to L and K using four (2) cam lock nuts. [Diagram shows panel Y being attached to panels L and K.] Note: 'Keep the holes of the Part L and Part K toward this direction as shown'. Close-up shows cam lock detail.

Step 26

Attach base panel. Attach B to Y using two (1) screws. [Diagram shows panel B being attached to panel Y.]

Step 27

Attach side panel. Attach Y to B using two (2) cam lock nuts. [Diagram shows panel Y being attached to panel B.]

Step 28

Attach side panels. Attach G, H, L, K to B using eight (3) screws. [Diagram shows side panels G, H, L, K being attached to base panel B.]

Step 29

Attach top panel. Attach X to G and H using four (3) screws. [Diagram shows top panel X being attached to side panels G and H.] Note: 'Keep the holes of the Part X toward this direction as shown'.

Step 30

Attach shelf. Attach A to X using six (3) screws. [Diagram shows shelf A being attached to panel X.]

Step 31

Attach top panel. Attach C to G, H, I, J using six (1) screws. [Diagram shows top panel C being attached to the main structure.]

Step 32

Attach internal panels. Attach L and K to C using six (2) cam lock nuts. Attach G and H to C using four (3) screws. [Diagram shows internal panels being attached to the top panel C.] Close-ups show cam lock and screw details.

Step 33

Reinforce back panel. Use twelve (6) buckles and twelve (7) buckles to reinforce the back panel. [Diagram shows buckles being attached to the back panel for reinforcement.] Note: 'Use the buckles to reinforce the back panel.'

Step 34

Attach drawer slides. Attach drawer slides (11) to Y and H using eight (8) screws. Attach drawer slides (11) to J and Z using four (11) screws. [Diagram shows drawer slides being attached to the main cabinet structure.] Note: 'Please rotate and remove parts 10 and 11 as instructed. Note: If necessary, please wear protective gloves during this step to avoid hand injuries.'

Step 35

Install hanging rod. Slide part (10) (cap) onto rod part (9). Attach rod part (9) to the cabinet using two (9) rods. [Diagram shows rod installation.] Note: 'Please slide part 10 onto the rod part 9 with the threads facing outwards.'

Step 36

Reinstall caps. Reinstall part (10) to part (11). [Diagram shows caps being reattached.] Note: 'reinstall part 10 to part 11'.

Step 37

Install adjustable shelf. Insert four (5) dowels into the desired height holes on the side panels G and Y. Place shelf E onto the dowels. [Diagram shows shelf E being placed on dowels.] Note: 'There are 3 heights for the shelf to be adjusted as you need.'

Step 38

Insert drawers. Align the wheels of the drawers with the slots on the cabinet and slide them in. [Diagram shows drawers being inserted into the cabinet.] Note: 'Please put the wheels align with the slots as the instruction shows, then slide into them.' Labels DL/DR (Drawer Left/Right) and CL/CR (Cabinet Left/Right) are shown.

Step 39

Install Tipping Restraint Hardware. Attach the Tipping Restraint Hardware (18) to the unit and a wall stud using one (3) screw (removed from elsewhere) and two (18) pieces. [Diagram shows the hardware being attached to the unit and the wall.] Note: 'We have included two Tipping Restraint Hardware set for this Unit. When properly installed, this restraint can provide protection against the unexpected tipping of the Unit due to small tremors, bumps or climbing. We strongly recommend mounting this hardware to a wall stud and your Unit. Note: You must install the Tipping Restraint Hardware with the unit in use to prevent any accidents or damage to the unit.'