Corner Closet System with Shelves
Assembly Instructions
Attention: Please ensure you have all parts before commencing assembly. Please read all the instructions before commencing.
Part List
- A: Top Panel (1 pc) - Rectangular panel.
- B: Bottom Panel (1 pc) - Rectangular panel.
- C: Side Panel (1 pc) - Tall, rectangular panel.
- D: Side Panel (1 pc) - Tall, rectangular panel.
- E: Side Panel (1 pc) - Tall, rectangular panel.
- F: Side Panel (1 pc) - Tall, rectangular panel.
- G: Shelf (1 pc) - Rectangular panel.
- H: Shelf (1 pc) - Rectangular panel.
- I: Back Panel (2 pcs) - Thin, rectangular panels.
- J: Drawer Front/Base (1 pc) - Rectangular panel.
- K: Top Panel (1 pc) - Rectangular panel with an angled corner.
- L: Side Panel (1 pc) - Tall, rectangular panel.
- M: Side Panel (1 pc) - Tall, rectangular panel.
- N: Side Panel (1 pc) - Tall, rectangular panel.
- O: Side Panel (1 pc) - Tall, rectangular panel.
- P: Shelf (1 pc) - Rectangular panel.
- Q: Divider/Support (2 pcs) - Long, narrow panel.
- R: Drawer Side (1 pc) - Rectangular panel.
- S: Drawer Bottom/Base (1 pc) - Rectangular panel.
- T: Drawer Front/Back (2 pcs) - Long, narrow panel.
- U: Drawer Support (1 pc) - Long, narrow panel.
- V: Drawer Support (1 pc) - Long, narrow panel.
Hardware List
- 1: M6x40 Screw (56 pcs) - Long screw.
- 2: M6x28 Screw (28 pcs) - Medium screw.
- 3: Ø12 Cam Lock Nut (28 pcs) - Circular nut.
- 4: M6x30 Screw (6 pcs) - Short screw.
- 5: M4x12 Screw (8 pcs) - Small screw.
- 6: 56-101cm Expandable Pole (2 pcs) - Adjustable pole.
- 7: Pole End Cap (2 pcs) - Small cap.
- 8: Pole Support Bracket (2 pcs) - Bracket for pole.
- 9: M6 Connector Plate (4 pcs) - Flat metal plate with holes.
- 10: M6 Bracket (2 pcs) - L-shaped bracket.
- 11: M3.5x12 Screw (40 pcs) - Very small screw.
- 12: M4x40 Screw (3 pcs) - Long screw.
- 13: Ø7x19 Dowel (8 pcs) - Wooden dowel.
- 14: Screwdriver (1 pc) - Tool.
- 15: M4 Allen Key (1 pc) - Tool.
*Please count and verify all parts before assembly . *
How to Install Camlocks
Step 1: Connect the male camlock as directed in the assembly instructions with a screwdriver. [DO NOT OVER TIGHTEN]
Illustration shows a male camlock being inserted into a panel with a screwdriver.
Step 2: Put the male camlock into the entry hole.
Illustration shows the male camlock positioned in the entry hole of a panel.
Step 3: Insert the female camlock as shown in the instruction. Note: Ensure that the arrow on the top of the camlock points toward the entry hole for the male camlock.
Illustration shows a female camlock being inserted into a panel, with an arrow indicating its orientation.
Step 4: Screw the female camlock clockwise with a screwdriver. You will feel a click when the camlock is locked in place. The camlock is now completed.
Illustration shows a screwdriver tightening the female camlock. A click sound is noted upon locking.
Assembly Steps
STEP 1
Attach Part S (Drawer Bottom/Base) to Part V (Drawer Support) using hardware 2 (M6x28 Screws) x4. Ensure the holes on Part S are aligned with the corresponding holes on Part V.
Diagram shows Part S being attached to Part V with four screws labeled '2'.
STEP 2
Attach Part U (Drawer Support) to the assembly from Step 1. Ensure the holes of Part S and Part U are oriented towards the direction shown in the diagram. Use hardware 3 (Cam Lock Nuts) x4.
Diagram shows Part U being attached to the assembly of S and V. Circles highlight connection points. A note indicates the orientation of holes on Part S and U.
STEP 3
Attach Part S (Drawer Bottom/Base) to Part V (Drawer Support) using hardware 2 (M6x28 Screws) x2. This step appears to reinforce the connection from Step 1.
Diagram shows Part S being attached to Part V with two screws labeled '2'.
STEP 4
Attach Part Q (Divider/Support) to the assembly from Step 3. Use hardware 3 (Cam Lock Nuts) x2.
Diagram shows Part Q being attached to the assembly. Circles highlight connection points. Hardware '3' is indicated.
STEP 5
Assemble the side panels. Attach Part N (Side Panel) and Part V (Drawer Support) to Part Q (Divider/Support) and Part S (Drawer Bottom/Base). Ensure the holes of Part Q are oriented towards the direction shown. Use hardware 1 (M6x40 Screws) x10.
Diagram shows parts N, Q, S, and V being assembled. Screws labeled '1' are shown. A note indicates the orientation of holes on Part Q.
STEP 6
Attach Part O (Side Panel) to the existing assembly. Use hardware 1 (M6x40 Screws) x10.
Diagram shows Part O being attached to the assembly of N, Q, S, and V. Screws labeled '1' are shown.
STEP 7
Attach Part K (Top Panel) to the assembly from Step 6. Use hardware 2 (M6x28 Screws) x6.
Diagram shows Part K being attached to the top of the assembly. Screws labeled '2' are shown.
STEP 8
Attach Part K (Top Panel) to the main structure (Parts N, Q, O). Use hardware 3 (Cam Lock Nuts) x6. A magnified view shows the cam lock mechanism connecting K to Q.
Diagram shows Part K being attached to the top of the main structure. Hardware '3' is indicated. A close-up shows the cam lock connection.
STEP 9
Assemble drawer components. Attach Part R (Drawer Side) and Part J (Drawer Front/Base) using hardware 2 (M6x28 Screws) x8.
Diagram shows Parts R and J being assembled with screws labeled '2'.
STEP 10
Attach Part T (Drawer Front/Back) to Part R (Drawer Side). Ensure the holes of Part R and Part T are oriented towards the direction shown. Use hardware 3 (Cam Lock Nuts) x4.
Diagram shows Parts R and T being assembled with hardware '3'. A note indicates the orientation of holes on Part R and T.
STEP 11
Attach Part M (Side Panel) to Part R (Drawer Side). Use hardware 1 (M6x40 Screws) x2.
Diagram shows Part M being attached to Part R with two screws labeled '1'.
STEP 12
Attach Part L (Side Panel) to the assembly of M and R. Attach Part T (Drawer Front/Back) to M and R. Use hardware 1 (M6x40 Screws) x6.
Diagram shows Part L being attached to M and R. Part T is also attached to M and R. Screws labeled '1' are shown.
STEP 13
Attach Part J (Drawer Front/Base) to the assembly of L and M. Use hardware 3 (Cam Lock Nuts) x4. A magnified view shows the cam lock connection.
Diagram shows Part J being attached to L and M. Hardware '3' is indicated. A close-up shows the cam lock connection.
STEP 14
Combine the main structure with drawer components. Attach the assembly from Step 13 (J, L, M) to the main unit (K, S, R, T, U). Use hardware 1 (M6x40 Screws) x4 and hardware 4 (M6x30 Screws) x4. A magnified view shows the connection points.
Diagram shows the combination of the drawer unit with the main cabinet structure. Hardware '1' and '4' are indicated. A close-up shows the screw connection.
STEP 15
Continue assembling the main unit. Attach Part K (Top Panel) to the structure. Use hardware 9 (M6 Connector Plates) x2, hardware 10 (M6 Brackets) x2, and hardware 11 (M3.5x12 Screws) x24. A diagram shows the use of a screwdriver.
Diagram shows further assembly of the main unit. Hardware '9', '10', and '11' are indicated. A screwdriver icon is present.
STEP 16
Assemble the side panels for the second section. Attach Part E (Side Panel) and Part F (Side Panel) to Part I (Back Panel) using hardware 1 (M6x40 Screws) x8. Ensure the holes of Part I are oriented towards the direction shown.
Diagram shows Parts E and F being attached to Part I with screws labeled '1'. A note indicates the orientation of holes on Part I.
STEP 17
Attach Part A (Top Panel) to the assembly from Step 16. Use hardware 1 (M6x40 Screws) x6. Ensure the holes of Part A are oriented towards the direction shown.
Diagram shows Part A being attached to the assembly of E, F, and I with screws labeled '1'. A note indicates the orientation of holes on Part A.
STEP 18
Attach Part K (Top Panel) to the structure from Step 17. Use hardware 2 (M6x28 Screws) x4.
Diagram shows Part K being attached to the top of the structure from Step 17 with screws labeled '2'.
STEP 19
Combine the two main sections. Attach the assembly from Step 18 to the assembly from Step 17. Use hardware 1 (M6x40 Screws) x2 and hardware 3 (Cam Lock Nuts) x4. A magnified view shows the connection points.
Diagram shows the two main cabinet sections being joined. Hardware '1' and '3' are indicated. A close-up shows the connection.
STEP 20
Assemble the drawer components. Attach Part J (Drawer Front/Base) to the drawer sides and base. Use hardware 2 (M6x28 Screws) x4.
Diagram shows the assembly of a drawer unit, with Part J being attached. Screws labeled '2' are indicated.
STEP 21
Assemble the drawer sides and back. Attach Part D (Side Panel) and Part C (Side Panel) to Part G (Shelf). Use hardware 1 (M6x40 Screws) x4.
Diagram shows Parts D and C being attached to Part G with screws labeled '1'.
STEP 22
Complete the drawer assembly. Attach the assembly from Step 21 (D, C, G) to Part J (Drawer Front/Base). Use hardware 3 (Cam Lock Nuts) x4. A magnified view shows the cam lock connection.
Diagram shows the drawer assembly being completed. Hardware '3' is indicated. A close-up shows the cam lock connection.
STEP 23
Attach Part A (Top Panel) and Part B (Bottom Panel) to the main cabinet structure. Use hardware 4 (M6x30 Screws) x2. A magnified view shows the connection points.
Diagram shows Parts A and B being attached to the main cabinet structure. Hardware '4' is indicated. A close-up shows the screw connection.
STEP 24
Further reinforce the main structure. Attach Part D (Side Panel) and Part C (Side Panel) to the assembly. Use hardware 1 (M6x40 Screws) x4, hardware 9 (M6 Connector Plates) x2, and hardware 11 (M3.5x12 Screws) x16. A diagram shows the use of a screwdriver and a tool icon.
Diagram shows additional parts (D, C) being attached to the main structure. Hardware '1', '9', and '11' are indicated. Icons for a screwdriver and Allen key are present.
STEP 25
Install the expandable poles. Attach the expandable poles (6) between the side panels. Use hardware 5 (M4x12 Screws) x8 to secure the pole support brackets (8) and pole end caps (7) x2. Note: Twist the expandable pole clockwise to tighten, anticlockwise to loosen.
Diagram shows the installation of expandable poles (6) in the closet sections. Hardware '5', '7', and '8' are indicated. A note explains how to adjust the pole.
STEP 26
Install the shelves. Insert dowels (13) x8 into the designated holes on the side panels. Place shelves H and P onto the dowels. There are 3 heights for the 2 shelves (Part H and Part P) to be adjusted as you need.
Diagram shows dowels (13) being inserted and shelves H and P being placed. A note explains shelf adjustability.
STEP 27
TIPPING RESTRAINT HARDWARE
Note: We have included three Tipping Restraint Hardware sets for this Unit. When properly installed, this restraint can provide protection against the unexpected tipping of the Unit due to small tremors, bumps or climbing. We strongly recommend mounting this hardware to a wall stud and your Unit.
Note: You must install the Tipping Restraint Hardware with the unit in use to prevent any accidents or damage to the unit.
Step 1: Attach the bracket (part of hardware 12) to the wall using appropriate fasteners (not explicitly shown, but implied by wall mounting). Use hardware 12 (M4x40 Screws) x3.
Step 2: Attach the other end of the restraint to the unit. Please unscrew one Part 1 screw first, then install Part 12.
Diagrams show two steps for installing the tipping restraint. Step 1 shows a bracket being secured to a wall. Step 2 shows the restraint connecting the wall to the unit. A magnified view shows the connection to the unit, involving hardware '1' and '12'.
