Wardrobe Assembly Manual
Important Information & Warnings
IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
AVOID SCRATCHES! To avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
IMPORTANT! It is important that any product assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.
Maintenance & Cleaning: For regular maintenance and cleaning of the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.
Installation Caution: Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.
ANTI-TOPPLE WARNING! Overtumed furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment. If not included with this product, please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully. ⚠️
Tools Required
Please prepare the following tools:
- Tape Measure ?
- Phillips Head Screwdriver ?
- Flathead Screwdriver ?
- Hammer ?
- Electric Drill ??
Caution: When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size. ⚠️❓
Parts List
The following parts and hardware are included:
- A x 84 (Ø6 x 34mm)
- B x 84 (Ø15 x 10mm)
- C x 44 (Ø8*30mm)
- D x 120 (Ø3.5*14mm)
- E x 6 (350mm)
- F x 8 (Ø4*12mm)
- G x 8 (Ø4*22mm)
- H x 4 (114mm)
- J x 4 (146mm)
- K x 6 (Ø35mm)
- L x 6 (Ø35mm)
- M x 26
- N x 2
- P x 2
- Q x 16 (Ø3.5*35mm)
- R x 1 (761mm)
Assembly Instructions
Slide Separation for Assembly
Slides must be separated before assembly. After separation, set aside until needed for assembly.
(Note: Instructions also provided in Spanish and French on original page.)
Diagram Description: Shows a drawer slide mechanism with components labeled: Mount, Cage, Lever, Runner.
- Step 1: Extend Slide - Extend the slide. ➡️
- Step 2: Push Lever Up - Push the lever up. ⬆️
- Step 3: Remove Runner - Remove the runner. ⬅️
Step 1: Frame Assembly
Connect side panels to base/top panels using parts A (x8) and D (x12), likely with E1/E2 components.
Step 2: Frame Assembly
Connect side panels to base/top panels using parts A (x8) and D (x12), likely with E1/E2 components.
Step 3: Drawer Runner Installation
Attach drawer runners to side panels using parts B (x8) and C (x8).
Step 4: Drawer Box Assembly
Assemble drawer boxes using parts B (x8) and Q (x16).
Step 5: Drawer Box Assembly
Attach drawer sides to the base using parts A (x16).
Step 6: Drawer Runner Attachment
Attach drawer runners to the drawer sides using parts A (x16).
Step 7: Main Frame Assembly
Attach drawer runners to the main frame panels using parts B (x8) and C (x8).
Step 8: Drawer Runner Attachment
Attach drawer runners to drawer sides using parts A (x8).
Step 9: Drawer Runner Attachment
Attach drawer runners to drawer sides using parts A (x8), D (x8), E (x2), and N (x2).
Step 10: Drawer Box Assembly
Assemble drawer boxes using parts B (x8) and C (x4).
Step 11: Frame Panel Attachment
Attach a panel to the frame using parts A (x4).
Step 12: Main Frame Assembly
Connect frame panels using parts B (x4) and C (x4).
Step 13: Main Frame Assembly
Connect frame panels using parts B (x8) and C (x8).
Step 14: Frame Panel Attachment
Attach panels to the frame using parts A (x12).
Step 15: Main Frame Assembly
Connect frame panels using parts B (x12) and C (x12).
Step 16: Main Frame Assembly
Connect frame panels using parts B (x8) and C (x8).
Step 17: Backboard Insertion
Insert the backboards. Use part R (761mm).
- Firstly, embed the backboard into the slot.
- Stand the entire closet up when the backboard is spaced of 4in/10cm inside the bottom slot.
- Finally, fully embed the backboard in the bottom slot.
Step 18: Assembled Frame View
Diagram shows the assembled wardrobe structure.
Step 19: Drawer Runner Attachment
Attach drawer runners to drawer sides using parts A (x20).
Step 20: Drawer Box Assembly
Assemble drawer boxes using parts B (x18) and associated screws (Ø15 x 10mm, Ø6 x 34mm).
Step 21: Drawer Component Assembly
Diagram shows assembly of drawer sides and bases.
Step 22: Drawer Component Assembly
Assemble drawer components using parts B (x2) and Q (x16).
Step 23: Drawer Box Assembly
Assemble drawer boxes using parts D (x16), E (x8), F (x8), and H (x4).
Step 24: Assembled Wardrobe with Drawers View
Diagram shows the assembled wardrobe with drawers.
Step 25: Drawer Runner Attachment
Attach drawer runners to drawer sides using parts D (x24), K (x6), and L (x6).
Step 26: Door and Hinge Attachment
Attach hinges to doors and frame using parts D (x48), G (x8), and J (x4).
Step 27: Handle/Decorative Element Attachment
Attach handles or decorative elements using parts D (x12) and M (x26).
Step 28: Wall Mounting
Secure the unit to the wall using parts P (x2) and appropriate wall anchors (not specified, but implied for anti-topple safety).
Step 29: Adjust & Align Door Hinges
Up & Down Adjustment:
- Loosen hinge screws.
- Move door up/down.
- Tighten hinge screws.
Left & Right Adjustment:
- Loosen hinge screws.
- Move door left/right.
- Tighten hinge screws.
Forward & Back Adjustment:
- Loosen hinge screws.
- Move door forward/backward.
- Tighten hinge screws.
Warranty Information
WARRANTY CLAIMS
There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
The product must be used in accordance with the instructions provided for health reasons.
For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.
Type of Warranty Claim
Failure to follow the furniture instructions will invalidate the warranty. Please pay attention.
Does not include damage during installation, but includes damage during transportation.
Scope of Responsibility
Shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
After using, the damage and scratches of the furniture are not covered by the warranty.
Warranty Coverage Areas
The Warranty Relates to All bought in The US and Covers The Following areas:
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns Policy
RETURNS
CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?
PLEASE FOLLOW THE BELOW INSTRUCTIONS:
- If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.
DEFECTIVE ITEMS
- If your item is defective in any way, i.e., it doesn't work but you can't identify why, in the first instance, please consult our FAQ section, as there may be a simple solution to the issue.
DAMAGED ITEMS
- If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
- In all circumstances, please save all packaging material and paperwork for the order.
- Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the retailer, you jeopardize your chances of making a claim, and you may not receive a credit for the return.
