Closet System Assembly Instruction
Welcome and Important Information
Two people are recommended for installation to greatly improve efficiency.
Thank you for purchasing our products. As a reliable seller, we strive to provide customers with 100% satisfied products and services. We hope you enjoy your shopping experience.
If you find any damage, missing parts, or dissatisfaction after receiving the product, please feel free to contact us. We will provide you with a 100% satisfactory solution.
TIPS:
- Please read this instruction manual carefully, follow it step by step, and pay attention to the notes to assemble quickly, safely, and correctly.
- Two people are recommended for installation to greatly improve efficiency.
- Put the screws in loosely until all pieces are together, then tighten them all. This will save time if you make a mistake during installation.
Part List
| Part | Description | Quantity |
|---|---|---|
| A | Top/Bottom Panel | 1 pc |
| B | Base Panel | 1 pc |
| C | Shelf Panel | 1 pc |
| D | Left Side Panel | 1 pc |
| E | Right Side Panel | 1 pc |
| F | Back Panel | 1 pc |
| G | Drawer Base Panel | 1 pc |
| H | Horizontal Support | 2 pcs |
| I | Hanging Rod Support | 1 pc |
| J | Drawer Front/Back Panel | 2 pcs |
| K | Drawer Side Panel | 3 pcs |
| L | Drawer Side Panel | 3 pcs |
| M | Drawer Base Panel | 3 pcs |
| N | Drawer Front Panel | 3 pcs |
| O | Drawer Bottom Panel | 3 pcs |
Hardware List
| No. | Icon | Description | Quantity |
|---|---|---|---|
| 1 | ? | M6x28 screw | 24 pcs |
| 2 | ⚙️ | Ø12 cam lock | 24 pcs |
| 3 | ? | M3x12 screw | 36 pcs |
| 4 | ? | M4x12 screw | 4 pcs |
| 5 | ? | M4x15 screw | 6 pcs |
| 6 | ? | M6x40 screw | 44 pcs |
| 7 | ➡️ | L300 Drawer Slide | 3 pcs |
| 8 | ➡️ | L300 Drawer Slide | 3 pcs |
| 9 | ➡️ | L300 Drawer Slide | 3 pcs |
| 10 | ➡️ | L300 Drawer Slide | 3 pcs |
| 11 | ? | Expandable Pole | 1 pc |
| 12 | ⚪ | Cylinder for Pole Mounting | 1 pc |
| 13 | ⚪ | Cylinder for Pole Mounting | 1 pc |
| 14 | ?️ | Tipping Restraint Hardware | 2 pcs |
| 15 | ? | M4x40 screw | 1 pc |
| 16 | ? | Screwdriver | 1 pc |
| 17 | ? | Drawer Handle | 3 pcs |
Using Camlocks
Camlocks are used to securely join panels. Follow these steps:
-
Connect Male Camlock: Insert the male camlock into its designated hole and secure it with a screwdriver.
[DO NOT OVER TIGHTEN]
- Insert Male Camlock: Push the male camlock into the entry hole of the connecting panel.
- Insert Female Camlock: Insert the female camlock into its hole on the connecting panel. Ensure the arrow on the top of the female camlock points towards the entry hole for the male camlock.
- Lock Camlock: Turn the female camlock clockwise with a screwdriver. You should feel a click when the camlock is locked in place, securing the joint.
Assembly Steps
STEP 1
Attach panels M and L to panel N. Use 12x Hardware 6 (M6x40 screws). This assembly is repeated 3 times for three drawer units.
STEP 2
Slide panel F into the grooves of the assembled M, N, L structure. This assembly is repeated 3 times.
STEP 3
Attach panel K to the assembled structure from Step 2. Use 12x Hardware 1 (M6x28 screws). This is repeated 3 times.
STEP 4
Connect panels M, L, and N to panel K. Use 12x Hardware 2 (Ø12 cam locks). This is repeated 3 times.
STEP 5
Attach drawer handles (Hardware 17) to panel K (drawer front). Use 6x Hardware 5 (M4x15 screws). This is repeated 3 times.
STEP 6
Attach drawer slides (Hardware 3, 8, 10) to panels L and M. Note the direction of the rollers on the slide rail. This step is part of the drawer assembly, repeated 3 times.
STEP 7
Attach side panels D and E to horizontal supports H and I. Use 12x Hardware 6 (M6x40 screws). Ensure the holes on D and E are oriented upwards and downwards as indicated in the diagram.
STEP 8
Attach base panel B to the structure formed in Step 7. Use 6x Hardware 6 (M6x40 screws). Ensure the holes on parts D and E are aligned as shown.
STEP 9
Attach top panel A to the structure. Use 6x Hardware 6 (M6x40 screws).
STEP 11
Attach drawer slides (Hardware 3, 7, 9) to panels F and G. Ensure the rollers are towards the bottom and note the direction of the rollers on the slide rail.
STEP 13
Attach drawer slides to panels F and G. Use 4x Hardware 1 (M6x28 screws) on panel F and 4x Hardware 1 (M6x28 screws) on panel G.
STEP 14
Attach panel C to the main structure. Use 2x Hardware 1 (M6x28 screws).
STEP 15
Attach panel J to panel C. Use 2x Hardware 2 (Ø12 cam locks).
STEP 16
Connect panels F and G to the structure (C and J). Use 4x Hardware 2 (Ø12 cam locks) and 8x Hardware 6 (M6x40 screws). Ensure the hole on panel F is facing upwards.
STEP 17
Attach panel B to the structure. Use 6x Hardware 1 (M6x28 screws).
STEP 18
Attach panels G and J to the structure. Use 4x Hardware 2 (Ø12 cam locks).
STEP 19
Attach panel J to the structure. Use 2x Hardware 2 (Ø12 cam locks).
STEP 20
Insert the assembled drawers into the main unit. Align the wheels with the slots as shown in the instruction, then slide them in.
STEP 21
Install the expandable pole (Hardware 11) between side panels D and E. Use cylinders (Hardware 12, 13) and screws (Hardware 4). Note: Twist the expandable pole clockwise to tighten, and anticlockwise to loosen.
Tipping Restraint Hardware Installation
We have included two Tipping Restraint Hardware sets for this Unit. When properly installed, this restraint can provide protection against unexpected tipping of the Unit due to small tremors, bumps, or climbing. We strongly recommend mounting this hardware to a wall stud and your Unit.
You must install the Tipping Restraint Hardware with the unit in use to prevent any accidents or damage to the unit.
Installation Steps:
- Please unscrew the Part 6 screw first, then install Part 14.
- Step 1: Attach one end of the restraint to the wall (preferably into a wall stud) using appropriate hardware.
- Step 2: Attach the other end of the restraint to the unit.
