Step2 Fiesta Cruise Water Table with Umbrella

Introduction

Thank you for purchasing the Step2® Fiesta Cruise Water Table with Umbrella™. We'd appreciate a few minutes of your time to complete a brief survey so we can continue providing you with great products. To participate, please visit our website at: www.step2.com/survey/?partnumber=894800

Thank you for your time, your friends at Step2.

Parts and Hardware

The following parts are included:

• Part A: Base/Boat Hull
• Part B: Legs (x3)
• Part C1: Connector (x2)
• Part C2: Connector (x2)
• Part C3: Connector (x1)
• Part D: Umbrella Pole Holder
• Part E: Spiral Slide Piece
• Part F: Slide Base Piece
• Part G: Slide Connector
• Part H: Slide Piece
• Part I: Slide Connector
• Part J: Support Piece
• Part K: Connector Piece
• Part L: Support Piece
• Part M: Umbrella Base
• Part N: Umbrella Pole
• Part O: Water Spout/Accessory
• Part P: Accessory
• Part Q: Accessory

Hardware includes:

• Screws: 4 x 1/2" (38.1 mm)
• Screws: 1 x 1" (2.54 cm)
• Screws: 12 x 1-1/2" (3.81 cm)

Safety Information

⚠️ WARNING: DROWNING HAZARD

There is a risk of young children drowning around open containers of water. Adult supervision is always required.

⚠️ WARNING: BURN HAZARD

Always check the temperature of the product before letting your children play with it. Remember that the product may cause burns if left in direct sunlight. Always be aware of the sun and weather conditions, and do not assume that the equipment is safe because the air temperature is not very high.

⚠️ WARNING: CHOKING HAZARD

Small parts. Sharp points. Adult assembly required.

OBSERVE ALL STATEMENTS AND WARNINGS TO REDUCE THE LIKELIHOOD OF SERIOUS OR FATAL INJURY. SAVE THIS SHEET FOR FUTURE REFERENCE.

• Intended for use by children from ages 2 years and up.
• Adult assembly required.
• Provide continuous adult supervision at all times.
• Instruct children not to use product until properly assembled.
• Front Section holds up to 3 gal. (11 l.) of water, or holds up to 25 lbs of sand.
• Rear Section holds up to 4 gal. (15 l.) of water.
• Take indoors or do not use when the temperature drops below 32°F (0°C).

INSPECT THIS PRODUCT BEFORE EACH USE. TIGHTLY SECURE CONNECTIONS AND REPLACE DAMAGED OR WORN COMPONENTS. CONTACT THE STEP2 COMPANY FOR REPLACEMENT PARTS.

Assembly Instructions

1. Steps 1-3: Attach legs (Part B) to the base (Part A) using screws. Repeat for all three legs.
2. Step 4a-4b: Connect connectors (Part C1, Part C2) to other parts.
3. Step 5: Connect multiple legs (Part B) to the base (Part A) using connectors (Part C1, Part C2).
4. Step 6: Attach connectors (Part C1, Part C3) to designated points on the base (Part A). A checkmark indicates correct placement.
5. Step 7: Insert and turn connector (Part C3).
6. Step 8a-8b: Insert connector (Part C2) into a hole.
7. Step 9: Place umbrella pole holder (Part D) onto the base (Part A).
8. Step 10: Snap slide piece (Part E) onto slide base piece (Part F). The instruction "Snap, Assemble, Fit, Click" is provided in multiple languages.
9. Step 11-12: Connect slide pieces (Part G, Part H, Part I) together, ensuring they snap into place.
10. Step 13-14: Continue assembling the slide structure by connecting pieces (Part G, Part I, Part E).
11. Step 15-16: Attach the assembled slide structure to the base (Part A) using screws.
12. Step 17: The complete slide structure is now attached to the base.
13. Step 18: Attach the umbrella base (Part M) to the umbrella pole (Part N).
14. Step 19-20: Ensure the longest side of Part J is on the same side as Part L for safety.
15. Step 21-22: Snap and connect parts (Part J, Part K, Part L) together.
16. Step 23-24: Place umbrella base (Part M), umbrella pole (Part N), and support pieces (Part J, Part L) onto the main structure.
17. Step 25-26: Attach connector pieces (Part K) to the main structure (Part A).
18. Step 27-28: Attach accessories (Part D, Part O, Part P, Part Q) to the main structure.
19. Step 29: Insert umbrella pole (Part R1) into its holder.
20. Step 30-31: Secure parts using screws (Part S) and connectors (Part R1). Note the difference between square and circular connectors.
21. Step 32-33: Attach the umbrella (Parts R1, R2) to the umbrella pole (Part N).
22. Step 34: Demonstrates how to hold the umbrella pole securely.

Cleaning and Disposal

Cleaning Instructions:

• General Cleaning: Use mild soapy water.
• Water should be changed frequently.
• Sanitize occasionally to remove organic debris and prevent bacterial growth.

Disposal Instructions:

Please recycle when possible. Disposal must be in compliance with all government regulations.