Safety Information & Warnings
Age Recommendation
Intended for children from 1½ years and up.
General Safety Guidelines
Observe all statements and warnings to reduce the likelihood of serious or fatal injury. Save this sheet for future reference.
- Provide continuous adult supervision at all times.
- Instruct children not to use the product until properly assembled.
- The table holds up to 5 gallons (18.92 liters) of water.
- Table legs are not removable; attempting to remove them can cause damage.
- Bring the product indoors or do not use it when the temperature drops below 32°F (0°C).
- Do not remove any screws once installed. For disassembly, remove only parts not secured by screws.
- Do not over-tighten screws, as they may not hold parts together appropriately.
- Screws are designed to pierce plastic and form their own threads.
Specific Warnings
⚠️ Choking Hazard
Contains small parts and sharp points. Adult assembly is required.
⚠️ Burn Hazard
Always check the product's temperature before letting children play with it. The product may cause burns if left in direct sunlight. Be aware of sun and weather conditions, and do not assume the equipment is safe simply because the air temperature is not very high.
⚠️ Drowning Hazard
There is a risk of young children drowning around open containers of water. Adult supervision is always required.
Assembly Instructions
Note on Assembly: The product has no pre-drilled holes; screws form their own threads. Apply pressure during installation. For screw installation tips, visit: www.step2.com/video-tips.
Step 1: Base Assembly
Attach part D1 and D2 to part C1 using fourteen (14) 3/4” (19.05 mm) screws.
Step 2: Side Panel Assembly
Attach parts C1, C2, and C3 together using eleven (11) 3/4” (19.05 mm) screws.
Step 3: Connect Base and Side
Snap part C1 into the assembled base structure.
Step 4: Attach Legs (Part 1)
Attach part B to part A using two (2) 1-1/4” (31.75 mm) screws.
Step 5: Attach Legs (Part 2)
Attach part A to part B using four (4) 1-1/4” (31.75 mm) screws.
Step 5a: Repeat Leg Attachment
Repeat steps 4 and 5 for the remaining two legs.
Step 6: Attach Main Structure
Attach part B to part A using two (2) 1-1/2” (38.10 mm) screws.
Step 7: Secure Main Structure
Attach parts B, C, and D to part A using four (4) 1-1/2” (38.10 mm) screws.
Step 8: Install Water Flow Parts
Assemble parts P, Q, and R into part A as shown in diagrams 8a through 8e.
Step 9: Attach Tower Base
Attach part D to the main structure (A).
Step 10: Attach Water Spout
Attach part C to the main structure (A).
Step 11: Connect Upper Structure
Attach part E to parts C and D.
Step 12: Secure Upper Structure
Secure part E to parts C and D using two (2) 1/2” (12.70 mm) screws.
Step 13: Final Upper Attachment
Secure part E to part C using two (2) 1/2” (12.70 mm) screws.
Step 14: Main Assembly Complete
The main structure is now assembled. Arrows indicate final connections.
Step 15: Attach Water Wheel Mount
Attach part D to part A using two (2) 1-1/2” (38.10 mm) screws.
Step 16: Attach Water Channel
Attach part C to part A using two (2) 1-1/2” (38.10 mm) screws.
Step 17: Install Water Paddles
Insert parts H into the designated slots.
Step 18: Attach Spinner
Attach parts J and K to part A.
Step 19: Attach Water Wheel
Snap part F into part D. Listen for a click [sound cue].
Step 20: Install Water Paddles
Insert parts M and N into part D.
Step 21: Install Water Funnels
Insert parts L and O into part D.
Step 22: Attach Shower Head
Attach part I to part A.
Step 23: Final Product View
The Shower Tower Splash Pond Water Table is now assembled.
Cleaning and Disposal
Cleaning Instructions
General Cleaning: Use a 50/50 mixture of white vinegar and water. Parents should thoroughly wash accessories before use. Water should be changed frequently. Sanitize occasionally to remove organic debris and prevent bacterial growth.
Disposal Instructions
Please recycle when possible. Disposal must be in compliance with all government regulations.
Product Care and Information
Product Inspection and Maintenance
Inspect this product before each use. Tightly secure connections and replace damaged or worn components. Contact The Step2 Company for replacement parts.
For more information, visit www.step2.com/survey/?partnumber=4138KL.
