Rain Showers & Unicorns Water Table™
Model: 4872
Product Information
The Step2 Rain Showers & Unicorns Water Table™ (Model 4872) is a water play table designed for children aged 1.5 years and older.
Manufactured by The Step2 Company, LLC.
10010 Aurora-Hudson Rd. Streetsboro, OH 44241 USA
Customer Service: 1-800-347-8372 (USA & Canada)
Website: www.step2.com
Safety Warnings
Choking Hazard
Contains small parts and sharp points. Adult assembly required.
Drowning Hazard
Risk of drowning for young children around open water containers. Continuous adult supervision is always required.
Burn Hazard
Always check the product's temperature before children play with it. The product may cause burns if left in direct sunlight. Be aware of sun and weather conditions.
General Safety Information
- Continuous adult supervision is required at all times.
- Instruct children not to use the product until properly assembled.
- The table holds up to 5 gallons (18.92 liters) of water.
- Table legs are not removable. Attempting to remove them may damage the product.
- Bring the product indoors or do not use when the temperature drops below 32°F (0°C).
- Do not remove any screws once installed. For disassembly, only remove parts not secured by screws.
- Do not over-tighten screws, as this may prevent parts from holding together appropriately.
- Screws are designed to pierce plastic and form their own threads.
Cleaning Instructions
General Cleaning
- Use a 50/50 mixture of white vinegar and water.
- Parents should thoroughly wash accessories before use.
- Change water frequently.
- Sanitize occasionally to remove organic debris and prevent bacterial growth.
Disposal Instructions
Please recycle when possible. Disposal must comply with all government regulations.
Pre-Use Inspection
Inspect this product before each use. Tightly secure connections and replace damaged or worn components. Contact The Step2 Company for replacement parts.
Assembly Instructions
Note: Screws form their own holes. Apply pressure during installation.
- Step 1 & 2: Attach leg components. Connect part D1 to part C1 using fourteen (x14) 3/4" (19.05 mm) screws. Then, attach part C3 to part C1 using eleven (x11) 3/4" (19.05 mm) screws.
- Step 3: Snap part C1 into its designated position.
- Step 4: Attach part B to the main base structure (part A).
- Step 5: Secure legs (part B) to the main base (part A) using four (x4) 1" (25.40 mm) screws. Repeat this process for the remaining two legs.
- Step 6: Attach a side piece (part B) to the main base (part A) using two (x2) 1-1/2" (38.10 mm) screws.
- Step 7: Attach another side piece (part B) to the main base (part A) using four (x4) 1-1/2" (38.10 mm) screws.
- Step 8: Assemble the drain plug mechanism. Connect part Q to part P. Insert this assembly into part A. Then, insert part R into part Q and secure with the cap.
- Step 9: Attach tower component (part D) to the main base (part A).
- Step 10: Attach water channels (part C) to the main base (part A).
- Step 11: Connect the water channel (part E) to the towers (part D) and channels (part C).
- Step 12: Secure the water channel (part E) to the structure using two (x2) 1/2" (12.70 mm) screws.
- Step 13: Attach another water channel component (part E) to part C using two (x2) 1/2" (12.70 mm) screws.
- Step 14: Complete the main structure assembly.
- Step 15: Attach an accessory component to the base (part A) using two (x2) 1-1/2" (38.10 mm) screws.
- Step 16: Attach another accessory component to the base (part A) using two (x2) 1-1/2" (38.10 mm) screws.
- Step 17: Insert parts H into their designated slots.
- Step 18: Attach play accessories (parts J and K) to the main base (part A).
- Step 19: Snap the spinning water features (parts F and G) into place.
- Step 20: Attach water wheel components (parts M and N) to the tower (part D) using two (x2) screws.
- Step 21: Attach water flow components (parts L and O) to the tower (part D).
- Step 22: Insert the water buckets (part I) into the main base (part A).
- Step 23: Finalize the assembly of the water flow and play features.