Step2 Dino Dig Sand & Water Table
Model: 8745
Manufacturer: The Step2 Company, LLC.
Website: www.step2.com
Important Safety Information
WARNING: BURN HAZARD
- Always check the temperature of the product before letting children play with it.
- Remember that the product may cause burns if left in direct sunlight.
- Always be aware of the sun and weather conditions, and do not assume that the equipment is safe because the air temperature is not very high.
WARNING: CHOKING HAZARD
- Small parts. Sharp points. Adult assembly required.
WARNING: DROWNING HAZARD
- There is a risk of young children drowning around open containers of water. Adult supervision is always required.
General Safety Information:
- Provide continuous adult supervision at all times.
- Instruct children not to use the product until properly assembled.
- Holds up to 4 gallons (15.14 L) of water and up to 20 lbs (9.07 kg) of sand.
- Take indoors or do not use when the temperature drops below 32°F (0°C).
- DO NOT remove any screws once installed. For disassembly, only remove parts not secured by screws.
- DO NOT over-tighten screws or they will not hold parts together appropriately.
- Screws are designed to pierce the plastic and form their own threads.
Parts List
- Part A: Waterfall/Slide structure
- Part B: Accessory piece
- Part C: Main water basin
- Part D: Dinosaur/Palm tree base structure
- Part E: Leg component
- Part F: Leg component
- Part G: Water tower base
Hardware:
- Screws (x6): 1-1/2" (38.10 mm)
- Screws (x6): 3/4" (19.05 mm)
- Screws (x4): 5/8" (15.88 mm)
- Screws (x2): 3/8" (9.53 mm)
- H1: Drain plug
- H2: Drain plug handle/stopper
- H3: Locking ring for drain plug
Assembly Instructions
- Combine H1 (drain plug) and H2 (handle).
- Insert the H1/H2 assembly into the designated hole in Part C (main basin).
- Secure H1 from the underside of Part C with H3 (locking ring).
- Tighten H3.
- Insert H2 into H1.
- Attach Part G (water tower base) to the main basin Part C.
- Attach one leg assembly (using E and F components, as shown in steps 10-12) to the base of Part C using three 3/4" screws.
- Attach another leg assembly (using E and F components) to the base of Part C using three 1-1/2" screws.
- Repeat steps 7 and 8 for the remaining two leg assemblies on the opposite side of the basin. (Total of two legs attached with 3/4" screws and two legs with 1-1/2" screws).
- Join Part E and Part F to form a complete leg assembly.
- Attach one side of the assembled leg (E+F) to the main basin Part C using one 5/8" screw.
- Attach the other side of the assembled leg (E+F) to the main basin Part C using three 5/8" screws. (This completes one leg assembly using all four 5/8" screws).
- Attach Part D (dinosaur/palm tree base structure) to the top of the assembled leg structure (E+F).
- Secure Part D to the leg assembly using two 3/8" screws.
- Attach accessory piece Part B to the main basin Part C.
- Insert the palm tree into the accessory piece Part B.
- Attach Part A (waterfall/slide structure) to the main basin Part C.
- The Dino Dig Sand & Water Table is now assembled.
Cleaning Instructions
General Cleaning:
- Use a 50/50 mixture of white vinegar and water.
- Water should be changed frequently.
- Sanitize occasionally to remove organic debris and prevent bacterial growth.
Disposal Instructions
- Please recycle when possible.
- Disposal must be in compliance with all government regulations.
Maintenance
Inspect this product before each use. Tightly secure connections and replace damaged or worn components. Contact The Step2 Company for replacement parts.
For surveys or feedback, visit: www.step2.com/survey/?partnumber=874500
