Step2 Rain Showers & Unicorns Water Table (Model 4872)

Safety Warnings and Information

Intended Use: For children aged 1½ years and up.

General Safety:

• Observe all statements and warnings to reduce the likelihood of serious or fatal injury.
• Keep this sheet for future reference.
• Provide continuous adult supervision at all times.
• Instruct children not to use the product until properly assembled.
• The table legs are not removable. Attempting to remove them can cause damage.
• Bring indoors or do not use when the temperature drops below 32°F (0°C).
• Do not remove any screws once installed. For disassembly, only remove parts not secured by screws.
• Do not over-tighten screws; they may not hold parts together appropriately. Screws are designed to pierce plastic and form their own threads.

Specific Hazards:

• ⚠️ CHOKING HAZARD: Small parts. Sharp points. Adult assembly required.
• ⚠️ BURN HAZARD: Always check the product's temperature before children play with it. The product may cause burns if left in direct sunlight. Be aware of sun and weather conditions.
• ⚠️ DROWNING HAZARD: Risk of young children drowning around open water containers. Adult supervision is always required.

Water Capacity: Holds up to 5 gallons (18.92 liters) of water.

Cleaning Instructions

• General Cleaning: Use a 50/50 mixture of white vinegar and water.
• Parents should thoroughly wash accessories before use.
• Change water frequently.
• Sanitize occasionally to remove organic debris and prevent bacterial growth.

Disposal Instructions

• Please recycle when possible. Disposal must be in compliance with all government regulations.

Assembly Instructions

Important Note: The product has no pre-drilled holes. Screws form their own threads. Apply pressure when inserting screws. (Note: Version B users skip to Step 3; Version A users skip to Step 4).

Parts Identification:

• Base Unit (A)
• Legs (B)
• Water channels/supports (C, C1, C2, C3)
• Main tower structure (D)
• Upper tray (E)
• Water wheel/spinner (F)
• Pump handle mechanism parts (G, H, J, K)
• Water scoops (I)
• Pump plunger/tube (L, M, N, O)
• Screws: x10 (1-1/2"), x6 (1-1/4"), x4 (1/2"), x14 (3/4"), x11 (3/4"), x2 (1-1/4"), x2 (1-1/2"), x2 (1/2")

1. Step 1: Attach 4 legs (B) to the base unit (A) using fourteen 3/4" screws (x14).
2. Step 2: Attach side supports (C1, C3) to the base unit (A) using eleven 3/4" screws (x11).
3. Step 3: Snap the central water channel piece (C2) into the base unit (A).
4. Step 4: Attach the remaining legs (B) to the base unit (A) using four 1-1/4" screws (x4).
5. Step 5: Attach the remaining legs (B) to the base unit (A) using two 1-1/4" screws (x2). Repeat steps 4-5 for the other two legs.
6. Step 6: Attach side panels (B) to the base unit (A) using two 1-1/2" screws (x2).
7. Step 7: Attach support structures (A) to the base unit (B) using four 1-1/2" screws (x4).
8. Step 8: Assemble and attach the water pump mechanism (P, Q, R) to the base unit (A).
9. Step 9: Attach the main tower structure (D) to the base unit (A).
10. Step 10: Attach the water wheel assembly (C) to the tower structure (A).
11. Step 11: Connect the upper tray (E) to the tower structure (D, C).
12. Step 12: Secure the upper tray (E) to the tower structure (D, C) with two 1/2" screws (x2).
13. Step 13: Secure the upper tray (E) to the tower structure (C) with two 1/2" screws (x2).
14. Step 14: The water table is now assembled. Arrows indicate water flow and play features.
15. Step 15: Attach component (A) to the base using two 1-1/2" screws (x2).
16. Step 16: Attach component (F) to the base using two 1-1/2" screws (x2).
17. Step 17: Insert components (H) into the designated slots on the structure.
18. Step 18: Assemble and attach components (J) and (K) to the main structure (A).
19. Step 19: Insert the water wheel/spinner (F) into the tower structure (D) until it snaps into place.
20. Step 20: Insert pump components (M) and (N) into the tower structure (D).
21. Step 21: Insert water pouring/channeling components (L) and (O) into the tower structure (D).
22. Step 22: Insert water scoops (I) into the base unit (A).
23. Step 23: The assembled water table is ready for play, featuring various water play accessories.