Mcombo Dog Crate Furniture

Product Precautions

• Read and follow the information in the user's manual.
• Please keep children away from small components to ensure safety.
• Please ventilate before use.
• Please note that the wood is not chew-proof.
• Please clean up water stains and pet excrement in time.
• Do not place overweight items.
• Please handle wood and other accessories properly.

Disclaimer

Mcombo asks users to read this manual completely before assembling and operating the new item. Mcombo is not responsible for any damage or injury incurred due to improper or unsafe use of the item. Mcombo specifically disclaims responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances. Please keep this manual for future reference.

Installation Preparation

1. Prepare a carpet or mat to protect your floor. Spread out all the accessories.
2. Prepare a pair of gloves to avoid being scratched by sharp wooden saw-dust that may occur during installation.
3. Open all the boxes to check that the accessories are complete and in good condition.
4. The box contains small components; please place them properly before installation to keep them away from children and ensure safety.
5. If using power tools, please set the speed to low speed in advance. High speed during installation may damage the wood.

Accessories List

Installation Instructions

Step 1

Attach part (11) to part (12) using four (4) screws labeled 'E'. Note: Screws 'E' need to be fully tightened.

Step 2

Attach part (13) to parts (11) and (12) using four (4) screws labeled 'F'. The diagram illustrates how to use the components: insert dowels, attach brackets, and secure with screws.

Step 3

Slide part (14) into the grooves of parts (11) and (12).

Step 4

Attach part (4) to the assembly using six (6) screws labeled 'E'. Note: Screws 'E' need to be fully tightened.

Step 5

Attach drawer slides (A) and (B) to part (3) using four (4) screws labeled 'K'. Note: Part (3) has two different sides.

Step 6

Attach part (3) to part (4) using two (2) screws labeled 'H'.

Step 7

Attach part (3) to part (4) using three (3) screws labeled 'J'.

Step 8

Attach parts (3) and (4) to the main frame (parts 11, 12) using four (4) screws labeled 'H'.

Step 9

Attach the top assembly (parts 3 and 4) to the main frame (parts 11, 12) using six (6) screws labeled 'F'.

Step 10

Slide part (14) into the frame.

Step 11

Secure part (14) to the frame using four (4) screws labeled 'H'.

Step 12

Attach part (16) to the frame using six (6) screws labeled 'J'.

Step 13

Insert part (10) into the frame.

Step 14

Attach parts (7) and (8) to part (7) using six (6) screws labeled 'E', two (2) screws labeled 'I', one (1) part (7), and one (1) part (8). Note: Ensure correct holes are used.

Step 15

Attach part (A) to part (7) using two (2) screws labeled 'K'.

Step 16

Attach part (7) to the main frame using four (4) screws labeled 'H'.

Step 17

Attach part (7) to the main frame using six (6) screws labeled 'F'.

Step 18

Insert part (10) into the frame.

Step 19

Attach part (15) to part (7) using six (6) screws labeled 'E', two (2) screws labeled 'I', one (1) part (8), and one (1) part (15). Note: Ensure correct holes are used.

Step 20

Attach part (B) to part (15) using two (2) screws labeled 'K'.

Step 21

Attach part (15) to the main frame using four (4) screws labeled 'H'.

Step 22

Attach part (15) to the main frame using six (6) screws labeled 'F'.

Step 23

Attach parts (5) and (17) to the frame using sixteen (16) screws labeled 'E', four (4) screws labeled 'N', and two (2) screws labeled 'I'. Also use one (1) part (5), two (2) parts (6), and one (1) part (17).

Step 24

Attach parts (5) and (17) to the frame using eight (8) screws labeled 'H' and two (2) parts labeled 'U'.

Step 25

Attach the frame to the main structure using ten (10) screws labeled 'F'.

Step 26

Attach part (6) to the frame using four (4) screws labeled 'H', four (4) screws labeled 'K', and two (2) brackets labeled 'S'.

Step 27

Attach part (7) to the frame using six (6) screws labeled 'F'.

Step 28

Stick ten (10) stickers labeled 'W' to the parts labeled 'F'. Stick eight (8) stickers labeled 'V' to the part labeled '16'.

Step 29

Insert drawers (2) into the unit.

Step 30

Attach part (1) to the top using nine (9) screws labeled 'E'. Note: Screws 'E' need to be fully tightened.

Step 31

Attach the top panel (1) to the unit using six (6) screws labeled 'H'.

Step 32

Attach the top panel (1) to the unit using nine (9) screws labeled 'F'.

Step 33

Attach eight (8) parts labeled 'Q' and eight (8) parts labeled 'N' to the doors.

Step 34

Attach parts (20) and (21) using twelve (12) screws labeled 'E'. Note: Screws 'E' need to be fully tightened.

Step 35

Insert panels (23), (22), and (26) first, then attach them using twelve (12) parts labeled 'G'.

Step 36

Insert parts (25) into the unit.

Step 37

Attach parts (24) to the unit using twelve (12) screws labeled 'L'.

Step 38

Attach drawer slides (C) and (D) to parts (20) and (21) using eight (8) screws labeled 'K'.

Step 39

Attach handles (P) to drawers (20) and (21) using two (2) screws labeled 'O' and four (4) screws labeled 'P'.

Step 40

Insert drawers (20) and (21) into the unit.

Step 41

Attach door panels (18) and (19) to the unit using two (2) hinges labeled 'R' and eight (8) screws labeled 'K'.

Step 42

Attach four (4) hinges labeled 'M' and eight (8) screws labeled 'N' to door panels (18) and (19).

Step 43

Attach door panels (18) and (19) with hinges to the main unit.

Step 44

Attach handles (P) to doors (18) and (19) using two (2) screws labeled 'O' and four (4) screws labeled 'P'.

Step 45

Secure doors using eight (8) screws labeled 'T'.

Step 46

Insert shelves (9) into the unit.

Step 47

Assembly complete.

Warranty

Wood: 1 Year

Hardware: 6 Months

Limitations Applicable to All Warranties: All warranties begin on the date of delivery. All warranties are to the original purchaser from MCOMBO / NEWACME LLC ONLY.

Warranty Detail Explanation

• Mcombo will replace defective parts or send a replacement item provided the warranty parts have not been subjected to misuse, abuse, or improper service.
• Exclusions include components with damage caused by: Contamination, Abuse, misuse, accident or negligence, Commercial use, or use other than normal, Improper operation, maintenance, or storage.
• Mcombo will pay standard shipping rates on all warranted parts for the first year. Replacement parts can also be sold at a discount price when the item is out of warranty.

Return/Replacement Policy

Mcombo offers a 30-day return/replace policy. During this time, Mcombo covers the shipping cost of return and replacement for defective and damaged items, and provides pre-paid return labels or pick-up service.

Note: Please disassemble the item before returning it to avoid significant costs due to oversized packaging.

Do not purchase return labels for a damaged defective item yourself.

If you have any problem returning the item, please contact Mcombo immediately for assistance.

Mcombo is not responsible for returns due to customer mistake or change of mind. However, Mcombo can assist customers in returning such items.

Note: The customer is responsible for freight costs unless the item is defective or returned due to being refused delivery or deemed undeliverable by the freight carrier, which may be subject to a 20% restocking fee.

Mcombo Customer Center

For any questions, suggestions, or issues, please contact Mcombo:

Phone: 1-323-597-1109 (Monday-Friday 9:00 AM - 5:00 PM)

Email: sales@mcombo.com (Respond within 24 hours)

Address: Newacme, 3980 Premier Ave, Memphis, TN, 38118

To efficiently resolve product issues, please provide your order number, the part number of the defective/missing part, the quantity of the issue parts, and send pictures. A reply is typically received within 24 hours.