D6RL Dash Cam User Manual
Preface
Welcome to use our products! Before installing and using this product for the first time, please read this material carefully, which will help you make better use of this product.
If you fail to operate this product according to the explanation of the manual and the requirements of this manual or operate this product by mistake due to misunderstanding and other reasons, it will lead to data loss or other losses. Please keep the product and the manual properly, operate in strictly accordance with the manual and back up the data in time.
We have collated and checked this manual strictly and carefully, but we can't guarantee that this manual is completely free of any errors and omissions. If you find anything, please contact our company.
The pictures in this manual are for reference only. If any picture is inconsistent with the actual display of the product, please refer to the actual display of the product.
In order to provide better services, we reserve the right to improve or modify the products and software programs described in this manual and the contents of this manual at any time without prior notice.
We are not responsible for the loss and loss of data and materials caused by misoperation of software and hardware, product maintenance or other conditions and are not responsible for other indirect losses caused thereby. Please back up your data and materials at any time.
If you find that the actual situation of this product is inconsistent with this manual during use, or you want the latest information or you have any questions or ideas, please contact our local distributor or online customer service.
We hope our products can meet your needs and serve you for a long time!
Matters Needing Attention in Using the Dash Cam
- This product is an auxiliary (vehicle driving recorder) product for safe driving. Any loss caused by malfunction, information loss or using this product is irrelevant to our company.
- This product is an auxiliary device for recording external images of vehicles. Due to the different driving environment and vehicle environment, some functions will not support. The unscheduled firmware upgrade in order to improve the product will change the performance of the product, and sometimes the camera will cannot record due to the environment, so the driving images recorded in this product is for reference only. The state of TF card will also lead to camera cannot record.
- Although this product can record and save the videos of accidents, it does not guarantee that all the accident videos can be recorded. Slight collision accidents can't start the collision sensor, so the video may not be recorded in the specialized folder.
- Be sure to disconnect the power supply when inserting or pulling out TF memory card.
- For the safe of product stability, please format TF card at least once a week.
- General TF cards have a lifetime, Long-term use may cause data to be unsaved. In this case, it is recommended to buy a new TF card to use, and our company will not be liable for data destruction caused by long-term use.
- Please do not install or operate this product while driving.
- This device may disturb the function of improperly protected medical equipment. If you have any question or are uncertain whether the medical equipment can shield external RF energy, please consult your doctor or medical equipment manufacturer.
- Please do not make this product subject to strong impact or vibration, so as not to damage the product and cause malfunction or unavailable.
- Please do not use it in an environment with excessive dust density, so as to prevent cameras and other parts from being contaminated with dust, which will affect the video effect.
- Please stop using this product before cleaning and maintenance.
- Please do not use chemical solvents or detergents to clean this product.
- Please do not unauthorized disassemble or modify this product.
- The ambient temperature range for the normal use of this device's function is –20 to 65 degrees Celsius. Exceeding this temperature range may lead to product malfunction, outbreak of fire or explosion.
- Please use it within the scope permitted by law.
The Packing List
After opening the package, please confirm whether the recorder is in good condition and whether the accessories are complete.
- Dash Cam Main Unit x1
- Cameras x2
- Power Cable x1
- USB Test Cable X1
- Bracket x1
- TF Memory Card (Optional) x1
- Wired Controller x1
Diagram of Product Appearance
A diagram showing the DVR unit with labels for Reset hole, Camera, Power interface, Wired controller, Speaker, and TF card slot.
Diagram of product connection
A wiring diagram illustrating the connections between the DVR unit, cameras, and other components.
The product structure and parameters will be continuously improved with the technological progress. The figure in this manual is only for reference. If there is a figure, and the description is inconsistent with the actual product, please refer to the actual display of the product.
Function Operation
Loop Recording Function
When the TF card is full, the old files recorded before will be deleted automatically in order. If there is an emergency file during recording, the file will not be deleted. The loop recording time can be set to 1/2/3/5 minutes.
G-sensor Trigger Lock File
After the sensitivity of G-sensor is on, when the device is recording, after the G-sensor triggers a collision and reaches the system preset level, the video will be locked to ensure that it will not be looped. The video file name is named GSR-XXXXXXXXXXX. When the TF card video file exceeds 10 "GSR" videos, the system will delete the earliest one.
Note
If the machine crashes due to improper operation when using this product, you can poke the reset hole and then turn it on again, the machine can be restored to normal use.
Mobile Phone APP Installation and Operation Instructions
WiFi APP is a mobile phone control software used with Vsysto DVR device. This software is connected to the DVR device via Wi-Fi, it can directly preview and playback the video on the mobile phone, easily realize that viewing the camera documents on the screen of mobile phone, setting or other operations. Subverting the control method of traditional cameras, bring you a new experience.
A QR code for Android app download and a QR code for Apple app download are displayed.
Scan the corresponding QR code above and download the App.
Conditions of use and product association:
- Smart terminal with Android 5.0 or higher or Apple terminal.
- Purchase a recorder terminal device that uses Vsysto design scheme, and connect the mobile phone WiFi to the camera correctly
DVR WiFi Default Name: MotoDV_XXX
Default password: 1234567890
※To ensure the normal use of APP functions, please update the APP to the latest version in time
Time of Synchronous DVR
After WiFi connection between the mobile phone and the DVR, open the APP, and the time of the mobile phone and the time of the DVR have been synchronized when “Instruction succeeded" prompted.
A screenshot shows "Command Succeed!" with navigation icons for Device, Online, Local, and Settings.
Live Preview (video/photo)
After connecting the DVR WiFi with mobile phone, open the APP, click "Connect Device" to enter the video preview status. In the video preview status, it is feasible to control the DVR to record and take photo. Click [switch camera] to switch front and rear camera images. Click [full screen] to switch to full screen display.
A screenshot of the WiFi Camera Viewer app is shown, with options to Enter Recorder, Record, and Take Pictures. Another screenshot shows a live view from the camera.
Browse DVR Files
Click [Online] to browse files in the DVR memory card.
A screenshot of the app's navigation bar with Device, Online, Local, and Settings icons is shown.
Replay the DVR Files
Browsing the DVR file interface in the "Online" option, click the file which you want to replay. Click [switch camera] on the upper left to switch files of the front and rear camera, F represents the front camera and R represents the rear camera.
Download or Delete DVR Files
Browsing the DVR file interface in the "Online" option, click Edit to select the file which you want to download or delete and then click "Save" or "Delete" as needed.
Screenshots show the process of selecting and downloading/deleting files, including a progress indicator for downloading.
Local Files Management
Click [Local] to enter the browsing interface of local files to replay/delete the files stored in the mobile phone, and the operation is similar to the online interface.
A screenshot of the app's navigation bar with Device, Online, Local, and Settings icons is shown.
DVR Parameter Setting
Click [Setup] to enter parameter setting interface of the DVR to set some parameters of the DVR in the APP. Among them, you can set the WiFi name and password of the DVR in Set SSID.
A screenshot shows the settings menu with options for Looping Video, Sound Record, GST, Reset Camera, Format SD Card, Set SSID, privacy policy, and service agreement. Firmware and APP versions are also displayed.
Quick Installation Guide
Preliminary Test
- Connect cam 1 & 2 to DVR host.
- Find the special USB power cable and connecting to your power bank or USB adaptor to do a quick test before installation.
- Prepare installation if everything looks good.
Instructions of the matched 12V→5V power module:
Normal Version: Connect red wire to battery positive, black wire to battery negative, yellow wire to the 12V port controlled by key ignition (ACC port).
Smart Version: The same connection with normal version but please waggle the power module (black box) around every 3 minutes to trigger the power supply, otherwise the electricity will be cut off automatically.
A diagram shows the HOST connected to a power bank or USB adapter. A note warns that the DVR will be burned out when output is over 5V.
Quick Installation Guide
- Locating the proper place to fix the front & rear camera, wired controller (optional), GPS tracker(optional) and main unit (normally placed under the seat).
- Planning the path of camera cable, wired controller cable, GPS tracker cable and power cable before installation.
- Fix and connect these parts by 3M tape, screws, cable ties on the proper place.
- 12V Power Module Connections:
- Normal power module: Connect red wire to battery positive, black wire to battery negative, yellow wire to the 12V port controlled by key ignition (ACC port).
- Smart power module: The DVR will be turned on while engine start, the DVR will be turned off after engine stop.
* Different motorcycle has different installation way, different DVR model has different cable connection definition (The diagram is for reference only)
The position of the main unit and lens cable should be away from the high-voltage circuit like xenon lamp, ignition plug etc.
If your motorcycle is a traditional carburetor system please try to change a suitable R-value ignition plug when you meet the interference phenomenon.
A diagram illustrates the installation on a motorcycle, showing connections for the 12V-5V Power Module, Cameras, and Wired Controller.
12V-5V POWER MODULE:
- Connect red wire to battery positive, black wire to battery negative, yellow wire to the 12V port controlled by key ignition (ACC port) if you choose normal power cable.
- Connect to battery positive and negative directly if you choose smart power cable.
WIRED CONTROLLER (optional): Fix the waterproof controller (optional) over handlebar.
HOST: Please fix the DVR under the seat if the model you purchase is not waterproof.
Quick Adjustment
- Release the lens cap, viewing the screen and rotate the lens body to adjust the horizontal view angle.
- Power Module Operation:
- Normal power module: The DVR will be turned on/off while engine on/off.
- Smart power module: The DVR will be turned on while engine start; The DVR will be turned off after engine stop.
Diagrams show the camera with 360° rotation capability.
Accessories installation
Camera
A diagram shows the Camera Module connected to an Extension Cable, which then connects to the main unit. It is noted that the concave and convex bayonet of the joint shall be matched correctly.
Please fix the camera with our standard extension cable before connecting to the DVR unless 0.5M is enough for you. Please keep the extension cable in case you will need it in someday.
Diagrams illustrate how to fix the camera using a bracket, double-sided foam tape, and screws. It is recommended to adjust the bracket for optimal view angles.
Battery Power Cable (optional)
Diagrams show the connection of the battery power cable to the battery anode and cathode, and then to the DVR. It is advised to connect the "U" shape terminal cable to the power module carefully to avoid damage from unsteady voltage.
Instructions and diagrams show how to fix the power module to the motorcycle using double-sided foam tape. The unit is noted as IP65 rainproof.
ACC Power Cable (optional)
Diagrams show the connection of the ACC power cable to the battery anode and cathode, and to a 12V wire controlled by the key. It is noted that the ACC position is generally below the lock.
Instructions and diagrams show how to fix the wired controller to the motorcycle using double-sided foam tape. The unit is noted as IP65 rainproof.
Wired Controller
Diagrams show the wired controller connected to the DVR. It features an LED Light to display the DVR working status and buttons to save an emergency video file and take a snapshot.
Wired controller indicator light description:
- Slow flash: normal video recording of DVR.
- Quick flash: after pressing the wired controller, the emergency video will be started and the front and rear cameras will take a picture at the same time, and the indicator light will flash quickly. When the current emergency video is recorded, the wired controller will resume the slow flashing state.
- Constant light: DVR is in standby state.
Note: The files generated by the wired controller will be named with "KEY". "KEY" video files recorded in emergency will not be overwritten by normal recorded video. But when the video files in the memory card exceed 10 KEY-XXXXXX videos, the system will automatically delete the oldest one.
Instructions and diagrams show how to fix the wired controller to the motorcycle using double-sided foam tape. It is noted as IP65 rainproof, and users are advised to keep the extension cable.
Troubleshooting
| Scenes | Malfunction Phenomenon | Cause/Solution |
|---|---|---|
| Startup Process | Cannot startup | 1. Use the USB power cable to test whether it can start up. 2. Please don't insert the card, don't connect the front and rear cameras, and see whether it can be turned on. If you can't turn it on, please contact customer service. |
| No recording when start up | Please check whether the TF card is in good condition. Please format the TF card, or replace the TF card. | |
| Image upside down | Please check whether the camera is installed upside down. | |
| Recording Process | Water ripple | 1. The picture flickers, water ripples. Please check whether the installation location is strong. 2. Please swap the front and rear cameras to determine whether it is a camera problem or a main unit problem. |
| Cameras have no image | Please check the camera for dirt and fingerprints; | |
| Video blurred | Before recording, please wipe the camera with the dust-free cloth. | |
| Foggy | Before recording, please wipe the camera with the dust-free cloth. | |
| Wrong recording time | 1. Find the time and date option in the menu settings, set the date and time manually, or connect to WIFI to enter the APP to update the time automatically. 2. If the DVR has GPS, it will also update to the current time after GPS positioning. If the GPS update time is different from the current time, please check the settings menu to see whether the time zone option is the local time zone. |
|
| Display is always on / Rest screen | The display is always on / Rest screen | 1. By default, the DVR will not operate after 1 minute, and the screen will shut down automatically. 2. If you want to keep the DVR's display screen always light on. You need to find the "turn off screen automatically" option in the menu setting interface and set it to off. |
| Can't find WiFi | Please check whether WiFi is turned off. You can check whether WiFi is turned off in the menu setting interface. | |
| WiFi password is incorrect | Find the reset system in the settings interface to restore factory settings. The default password is 1234567890 | |
| WiFi Connection Process | WiFi connection failed | After turning off the WIFI function of the mobile phone, turn on the WIFI function and connect to the WIFI again. |
| WIFI has been connected to the APP, but there is no image, or the command failed | For Android, please turn off WiFi helper and turn off 4G network. Reconnect to WIFI. | |
| Installation Process | Installation, wiring, fixed cameras | 1. Try to keep away the engine and high voltage package when installing the cameras cables. 2. The front and rear cameras must be installed in a strong location which has little vibration. |
| ACC power cable installation | The red wire is connected to the positive electrode of the battery, the black wire is connected to the negative electrode, and the yellow wire is connected to the ACC which is controlled by the key. The ACC position is generally below the lock. If you can't find it, please go to the repair shop to install it. | |
| GPS module installation | It is recommended to place the GPS module in an open location at the front or rear of the vehicle. Place the three letters which is on the GPS towards the sky, and the installation position should not be close to cameras. | |
| Wired controller installation | It is recommended to install it near the handlebar of the motorcycle to observe the video recording status of the DVR during driving conveniently and to operate the wired controller conveniently. |
! ATTENTION
Solutions for WiFi Connection Problem on Some Mobile Phones:
Android: Firstly turn off your phone's mobile data and then connect to DVR's WiFi. If the prompt "Trust this Network" appears, you must click “YES”, because Android phone forbids mobile data to ensure the recorded video file transferring speed from DVR to mobile phone.
IOS: Allows the mobile phone to continue to use the mobile network after connecting to the recorder via WIFI, but it affects the speed of downloading the DVR's video files to the mobile phone.
