VINGLI Drawer Dresser Assembly Instructions

Return & Warranty

Thank you for choosing VINGLI products. We hope you are completely satisfied with your purchase and enjoy it for years to come. Your satisfaction is our highest pursuit.

Return Policy: If you wish to return your 3-drawer dresser for any reason, please contact VINGLI customer service directly before returning it to the retailer. Our Customer Service organization can answer concerns and assist with any questions about your new product. The item must be returned in good condition, in its original box, with all original proof of purchase, parts, and accessories, within the time frame specified by the retailer.

Warranty: This product is warranted to be free from defects in material and workmanship for one year from the date of original purchase. VINGLI agrees to remedy any such defect through repair or replacement of defective parts. This warranty is limited to parts and does not include assembly labor. It does not apply to products that have been improperly assembled, subjected to misuse or abuse, or altered or repaired in any way. Repaired or replaced components are warranted for the remainder of the original warranty period. For assistance with assembly, identifying parts, product information, or ordering parts, please contact VINGLI freely.

Before Starting

Before Using Product:

• Read each step carefully before starting. It is very important that each step is performed in the correct order; failure to follow the sequence may lead to assembly difficulties.
• Ensure all parts are included. Most board parts are labeled or stamped on the raw edge.
• Prepare a flathead and Phillips screwdriver. A power screwdriver is recommended.
• Recommended number of people for assembly: 1 (however, having an extra hand is always beneficial).
• Estimated assembly time: 4 hours.
• Work in a spacious area, preferably on a carpet, or use the cardboard packaging to protect your floor and the product.
• For a smooth assembly process, keep screws lightly tightened during assembly. Firmly tighten all screws after the entire product is assembled.

WARNING:

• Do not allow children to climb on the unit.
• Serious or fatal crushing injuries can occur from furniture tip-over. To prevent this furniture from tipping over, it must be permanently fixed to the wall. Fixing devices for the wall are not included, as different wall materials require different types of fixing devices. Use fixing devices suitable for your home's walls. For advice on suitable fixing systems, contact your local specialized dealer.
• Avoid sharp objects or corrosive chemicals to prevent damage to the product.
• During assembly, keep parts and packaging materials away from children and pets, as there could be potential injury and choking hazards.

Assembly Tips

Applicable Model

Overall Size: 31.5"W x 17.7"D x 29.9"H (80cm x 45cm x 76cm L x W x H)

Features: Solid Wood, DIY Color, 3-Drawer Storage Space

Estimated Time for Assembly: 240 minutes (4 hours)

Caution:

1. This product is designed for home use and not intended for commercial use.
2. This product contains small components. Please ensure they are kept away from small children.
3. Be careful when using power tools to assemble your furniture, as they may strip or damage the parts.

Identify Parts

One unit per box. The following parts are included:

1. Top Panel (x1)
2. Left Side Panel (x1)
3. Right Side Panel (x1)
4. Back Upper Support Panel (x1)
5. Front Foot Panel (x1)
6. Back Panel (x1)
7. Back Panel Connecting Strip (x1)
8. Back Panel (x1)
9. Drawer Back Panel (x3)
10. Drawer Left Panel (x3)
11. Drawer Right Panel (x3)
12. Drawer Bottom Panel (x3)
13. Drawer Bottom Support Panel (x3)
14. Back Lower Support Panel (x1)
15. Drawer Front Panel (x3)

Components

The following hardware components are included:

1. Component A: Wood Dowel (x4) - Cylindrical wooden pegs for alignment.
2. Component B: Cam Bolt (x34) - Metal bolts with a screw thread and a head designed to engage with cam locks.
3. Component C: Cam Lock (x34) - Circular metal fasteners used to secure panels when engaged with cam bolts.
4. Component D: Screw (4x30mm) (x12) - Standard screws for assembly.
5. Component E: Handle (x6) - Drawer handles.
6. Component F: Screw (3x25mm) (x6) - Screws for attaching handles.
7. Component G: Drawer Slide (x6) - Metal runners for drawers.
8. Component H: Screw (3x12mm) (x24) - Smaller screws, often used with drawer slides.
9. Component I: Expansion Screw (x2) - Anchors for securing the unit to a wall.
10. Component J: Screw (4x50mm) (x2) - Longer screws for wall mounting.
11. Component K: Screw (2x10mm) (x16) - Small screws for back panels.

Assembly Steps

Follow these steps carefully to assemble your VINGLI Drawer Dresser.

STEP 1

Press the detach button on the Drawer Slide (G) to separate it into two parts: G1 and G2.

Diagram Description: A hand is shown pressing a button on a drawer slide (G) to separate it into two pieces, labeled G1 and G2.

STEP 2

Fix Drawer Slide (G1) to Panel #2 with Screw (H). Screw Cam Bolt (B) into Panel #2. Note: The pre-drilled holes on the panel for locating the slide rail are small; look carefully.

Diagram Description: Shows two side panels (labeled '2') with pre-drilled holes. Drawer slides (G1) are attached to these panels using screws (H). Cam bolts (B) are screwed into the panels. A close-up shows a screw (H) being inserted into a pre-drilled hole on the slide (G1) and panel (2). Arrows indicate placement.

STEP 3

Fix Drawer Slide (G1) to Panel #3 with Screw (H) in the same way as Step 2. Screw Cam Bolt (B) into Panel #3.

Diagram Description: Similar to Step 2, showing drawer slides (G1) attached to panel '3' with screws (H) and cam bolts (B) inserted into the panel.

STEP 4

Connect Panel #4, #5, and #14 to Panel #3 in turn and fix them with Cam Lock (C).

Diagram Description: Shows panels 4, 5, and 14 being connected to panel 3. Cam locks (C) are inserted into holes and turned to secure the panels. A close-up shows how to insert and turn a cam lock (C) to engage with a cam bolt.

STEP 5

Connect Panel #2 to the frame and fix it with Cam Lock (C).

Diagram Description: Shows panel 2 being connected to the assembled frame (panels 3, 4, 5, 14). Cam locks (C) are used to secure panel 2 to the frame.

STEP 6

Insert Wood Dowel (A) into the top holes of Panel #2 and #3.

Diagram Description: Shows wood dowels (A) being inserted into the top holes of panels 2 and 3.

STEP 7

Screw Cam Bolt (B) into Panel #1.

Diagram Description: Shows cam bolts (B) being screwed into the underside of panel 1 (the top panel).

STEP 8

Connect Panel #1 to the frame and fix it with Cam Lock (C).

Diagram Description: Shows panel 1 being placed on top of the assembled frame (panels 2, 3). Cam locks (C) are used to secure panel 1 to the frame. A close-up shows the cam lock mechanism.

STEP 9

Fix the back panels (6, 7, 8) with Screw (K).

Diagram Description: Shows the back panels (labeled 6, 7, 8) being attached to the rear of the dresser frame using screws (K). Arrows indicate screw placement. A note indicates pre-drilled holes for an anti-tipping device.

STEP 10

Drill holes in the wall, insert Expansion Screw (I), and fix the item to the wall with Screw (J) as needed.

Diagram Description: Shows the dresser positioned against a wall. Expansion screws (I) are inserted into the wall. The dresser is then secured to the wall using screws (J) through pre-drilled holes in the top panel (1) and side panel (4).

STEP 11

Assemble the drawer components: Screw Cam Bolt (B) into Panel #15 and #9. Attach Drawer Slide (G2) to Panel #10 and #11 with Screw (H). This step is repeated three times (x3).

Diagram Description: Shows cam bolts (B) being screwed into panels 15 and 9. Drawer slides (G2) are attached to panels 10 and 11 using screws (H). The 'x3' indicates this process is for three drawers.

STEP 12

Assemble the drawer according to the schematic diagrams. Fix the Handle (E) to Panel #15 with Screw (F). This is repeated three times (x3).

Diagram Description: Shows drawer components (9, 10, 11, 12, 13, 15) being assembled into drawers. Cam locks (C) and screws (D) are used to join panels. Handles (E) are attached to drawer front panels (15) using screws (F). The 'x3' indicates this is for three drawers.

STEP 13

Pull Drawer Slide (G1) out first. Keep the drawer level and insert the drawer with the slides aligned. Note: Failure to level may result in damage to the slides.

Diagram Description: Shows a drawer slide (G1) being pulled out. A completed drawer is shown being inserted into the dresser, aligning the slides. The dresser top is indicated with a weight capacity of 110 lbs, and each drawer with 22 lbs capacity. Arrows indicate the direction of insertion.

FAQs

• 1. What should I do when I received a defected item?
  Please feel free to contact VINGLI customer service via the link where you purchased this item with your order ID and a picture of the defective part. VINGLI is eager to help you make it right.
• 2. Is it easy to put the screws to the panels?
  Yes. As long as you follow the instructions and use the correct screws in the correct holes, it is easy to screw them into the pre-drilled holes.
• 3. Why are my drawers not aligned?
  The problem likely lies in the assembly of the slides. Please follow steps 1-3 and 11 on the instruction, paying more attention to align the holes on the slides with the holes on the panel.
• 4. How to insert the drawers?
  Refer back to step 14 (Note: This likely refers to the general process of drawer insertion, possibly implied in earlier steps or a missing page). Ensure the inner slides on the drawer are attached correctly with the outer slides, then push the drawer into the cabinet. If the slides do not run smoothly, please check if the slides and panels are installed correctly.
• 5. What should I do if I forget to anchor the item to the wall until I've inserted the drawers?
  No problem. You can remove the drawer by pinching the small tongues on both sides of the drawer in the direction indicated by the arrows (similar to splitting the slides in step 1). Then, anchor the item to the wall through the inside of the cabinet.
• 6. Can I paint after it's all assembled?
  Yes, but it is recommended to paint before assembly to ensure that every corner is covered.

Supplementary Instructions for Safe Use

WARNING: Children have died from furniture tipover. To reduce the risk of furniture tipover:

• ALWAYS install the tipover restraint provided. [?]
• NEVER put a TV on this product. [❌?]
• NEVER allow children to stand, climb, or hang on drawers, doors, or shelves. [❌?‍♂️]
• NEVER open more than one drawer at a time. [❌↔️]
• Place heaviest items in the lowest drawers. [⬇️?]
• Do not defeat or remove the drawer interlock system. [⚙️?]
• This is a permanent label. Do not remove! [⚠️?️]

French Translation (ATTENTION): Des enfants sont morts du basculement des meubles. Pour réduire le risque de basculement des meubles:

• TOUJOURS installer la retenue de basculement fournie.
• NE JAMAIS mettre de téléviseur sur ce produit.
• NE JAMAIS permettre aux enfants de se tenir debout, de grimper, ou de s'accrocher à des tiroirs, des portes ou des étagères.
• N'ouvrez JAMAIS plus d'un tiroir à la fois.
• Placez les objets les plus lourds dans les tiroirs les plus bas.
• Ne désactivez pas et ne retirez pas le système de verrouillage du tiroir.
• Ceci est une étiquette permanente. Ne pas enlever!

German Translation (WARNUNG): Kinder sind an einem Möbelkipp gestorben. So verringern Sie das Risiko eines Umkippens von Möbeln:

• Installieren Sie IMMER die mitgelieferte Kipprückhaltevorrichtung.
• Stellen Sie NIEMALS einen Fernseher an dieses Produkt.
• Lassen Sie Kinder NIEMALS an Schubladen, Türen oder Regalen stehen, klettern oder hängen.
• Öffnen Sie NIEMALS mehr als eine Schublade gleichzeitig.
• Legen Sie schwerste Gegenstände in die untersten Schubladen.
• Besiegen oder entfernen Sie das Schubladenverriegelungssystem nicht.
• Dies ist ein dauerhaftes Etikett. Nicht entfernen!