Vingli Assembly Instruction

Introduction

Guide of Manual

Please read the following instruction carefully and use the product properly. Keep this manual and hand it over when you transfer the product. This summary may not include every detailed information of all variations and considered steps. Please contact Vingli when further information and help are needed.

Before Starting

Recommended number of people for assembly: 2

Read each section carefully before starting. It is very important that each step is performed in the correct order. If these steps are not followed in sequence, assembly difficulties will occur.

• Make sure all parts are included. Most board parts are labeled or stamped on the raw edge.
• Assemble the product according to the steps on the diagram strictly. Do not fully tighten the screws until all pieces are situated in place.
• For continued use, it is suggested to regularly check the tightness of bolts and connections to ensure safety.
• Work in a spacious area, preferably on a carpet, near the place the unit will be located.
• Have the following tools close at hand: [tools-image-placeholder]

Warning

• Keep all accessories and packaging of this product away from babies, children, and pets as they potentially pose a hazard.
• The units contain small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or serious injury could occur.
• Do not put the product in a humid environment for a long time to prevent mildew.
• Keep the product away from sharp objects and corrosive chemicals to avoid damage.
• Do not overload the unit. If any shelf, top, or bottom of the unit bows or bends, it is overloaded. The shelf, top, or bottom could collapse and cause serious bodily injury and/or damage to personal belongings.
• Do not climb or step on the unit. The unit may become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur.

Part List

Start assembling furniture

[Diagram of furniture assembly steps]

Components of furniture

Please check the board number and the hole on the board:

1. LEFT SIDE PANEL (570x384mm, QTY:1PC)
2. RIGHT SIDE PANEL (570x383mm, QTY:1PC)
3. BACK PANEL (570x370mm, QTY:1PC)
4. TOP PANEL (400x400mm, QTY:1PC)
5. BOTTOM PANEL (400x383mm, QTY:1PC)
6. BOTTOM DRAWER FRONT PANEL (400x297mm, QTY:1PC)
7. MIDDLE DRAWER FRONT PANEL (400x145mm, QTY:1PC)
8. TOP DRAWER FRONT PANEL (400x145mm, QTY:1PC)
9. BOTTOM DRAWER LEFT PANEL (350x150mm, QTY:1PC)
10. BOTTOM DRAWER RIGHT PANEL (350x150mm, QTY:1PC)
11. BOTTOM DRAWER BACK PANEL (316x277mm, QTY:1PC)
12. TOP/MIDDLE DRAWER LEFT PANEL (350x75mm, QTY:2PCS)
13. TOP/MIDDLE DRAWER RIGHT PANEL (350x75mm, QTY:2PCS)
14. TOP/MIDDLE DRAWER BACK PANEL (316X75mm, QTY:2PCS)
15. DRAWER BOTTOM PANEL (345X323mm, QTY:3PCS)
16. BOTTOM DRAWER CASTER SUPPORT PANEL (315X70mm, QTY:1PC)
17. CASTER STAND (70X70mm, QTY:1PC)
18. DRAWER SEPARATOR PANEL (370X70mm, QTY:2PC)

Hardware accessories

• A1: CAM BOLT (30PCS)
• A2: CAM LOCK (30PCS)
• B: SCREW (M5x50mm, 12PCS)
• C: SCREW (M3.5x12mm, 43PCS)
• D: HANDLE (3PCS)
• E: HANDLE SCREW (M4x18mm, 6PCS)
• F: SCREW (M7x40mm, 4PCS)
• G: DRAWER SLIDE (6PCS)
• H: FILE FOLDER SUPPORT BAR (2PCS)
• I: LOCK (3PC)
• J: CASTERS (1PCS)
• K: SCREW (M3.5x25mm, 4PCS)
• L: WOOD DOWEL (1PC)
• M: LOCK LATCH (2PC)
• N: CASTER PLATE (5PC)
• O: SCREW (12PC)

Assembly Steps

Step 1

Using screw C to fix M on Panel 18.

[Diagram for Step 1]

Step 2

As shown in illustration, put screw C through the marked holes and fix Drawer Slide G on Panel 1 and 2.

[Diagram for Step 2]

Step 3

Connect 2 pcs panel 18 with panel 1 by tightening cam bolt A1, and connect panel 3 with panel 1 by tightening cam lock A2. (Note: For panel 18, the side with M should face down, and on Front)

[Diagram for Step 3]

Step 4

Connect 2 pcs panel 18 with panel 2 by tightening cam bolt A1, and connect panel 2 with panel 3 by tightening cam lock A2.

[Diagram for Step 4]

Step 5

Use bolt A to tighten connect panel 4 with panel 1 and 2, pay attention to distinguish the front and back side of panel 4 (holes on the front).

[Diagram for Step 5]

Step 6

Embed N in the holes of panel 5 and 17, pay attention to the hole position in illustration, be sure to fit N with the board surface, then tighten with screw C.

[Diagram for Step 6]

Step 7

Drive roller J in installed N. Note: Please fully tighten all the rollers, or the cabinet will be uneven.

[Diagram for Step 7]

Step 8

Use screw F to fix panel 5 under panel 1 and 2, the side with roller J should face down.

[Diagram for Step 8]

Step 9

Use screw B connect panel 12 and 13 with 14, then embed panel 15 in the notch of panel 12, 13 and 14.

[Diagram for Step 9]

Step 10

Use bolt A connect panel 7 or panel 8 with the front end side of panel 12 and 13, and embed panel 15 in the notch of panel 7 or 8 for making panel 12 and 13 fit in panel 7 or panel 8.

[Diagram for Step 10]

Step 11

Follow those marked hole position, using screw C to fix G on the side of panel 12 and 13, the front end of G should fit in panel 7 or 8.

[Diagram for Step 11]

Step 12

Put E through the hole of panel 7 or 8 and connect with D.

[Diagram for Step 12]

Step 13

First, take the lock ring off from I. Next put I through panel 7 or 8, fix outside by the lock ring, keep the side with latch upward, and then use screw O to fix inside.

[Diagram for Step 13]

Step 14

Follow the illustration' marked hole position, use A to connect panel 16 with panel 9 and 10, and then use screw C to fix G on the outside of panel 9 and 10, the front ending of G should be aligned with front ending of 9 and 10.

[Diagram for Step 14]

Step 15

Use screw B to connect panel 11 with panel 9 and 10, embed panel 15 in the notch of panel 9, 10 and 11, after that, embed H in the hole of panel 11.

[Diagram for Step 15]

Step 16

Use bolt A to connect panel 6 with panel 9 and 10. Note: panel 15 should embed in the notch of panel 6, and H should embed in the hole of panel 6.

[Diagram for Step 16]

Step 17

Put E through the hole of panel 6 and connect with D.

[Diagram for Step 17]

Step 18

First, take the lock ring off from I. Next put I through panel 6, fix outside by the lock ring, keep the side with latch upward, and then use screw O to fix inside.

[Diagram for Step 18]

Step 19

Follow those marked hole position, using screw C to fix G on the side of panel 12 and 13, the front end of G should fit in panel 7 or 8.

[Diagram for Step 19]

Step 20

Put screw K through panel 17 and screw in panel 16, and then screw roller J in N (has been installed in panel 17 at STEP 6).

[Diagram for Step 20]

Step 21

Show as illustration, pull out the G first, the slide ball was also pulled to the front side, then fit the slide of panel 7 with G and then embed. Notice: if the slide on panel 7 has not fit well with G, may cause G damaged.

[Diagram for Step 21]

Step 22

Show as illustration, pull out the G first, the slide ball was also pulled to the front side, then fit the slide of panel 8 with G and then embed. Notice: if the slide on panel 8 has not fit well with G, may cause G damaged.

[Diagram for Step 22]

Step 23

As illustration shown, pull out the G first, the slide ball was also pulled to the front side, then fit the slide of panel 6 with G and then embed. Notice: if the slide on panel 6 has not fit well with G, may cause G damaged.

[Diagram for Step 23]

Warning

WEIGHT LIMITS:

• Top Panel: 10kg/22LBS
• Drawer 1 (Top): 2kg/4.4LBS
• Drawer 2 (Middle): 2kg/4.4LBS
• Drawer 3 (Bottom): 4kg/8.8LBS

Enjoy your furniture!