VINGLI FILE CABINET ASSEMBLY INSTRUCTION

Welcome

Thank you for purchasing from VINGLI!

If parts are missing or damaged, please contact VINGLI customer service via email. VINGLI will gladly ship replacement parts free of charge.

▲ IMPORTANT

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Before Starting

Before Using Product

• ✔️ Read each step carefully before starting. It is very important that each step is performed in the correct order. If these steps are not followed in sequence, assembly difficulties will occur.
• ✔️ Make sure all parts are included. Most board parts are labeled or stamped on the raw edge.
• ✔️ Have the following tools: Screwdriver, Drill (optional).
• ?‍?‍? Recommended number of people for assembly: 1 (however, it is always better to have an extra hand). Estimated assembly time is 2 hours with an electric screwdriver.
• ? Work in a spacious area and near where the unit will be used, preferably on a carpet, or use a piece of the cardboard packaging to protect your floor and product.
• ⚙️ For a smooth assembly process, we suggest you keep a light tightness for all the screws during assembly. After the whole product is assembled, firmly tighten all the screws.

⚠️ WARNING:

Components of Furniture

Please check the board number and the hole on the board.

Hardware accessories

"A" Hardware installation example: This shows the process of inserting a Cam Bolt into a panel, then attaching another panel and securing it with a Cam Lock, which is rotated to lock.

Assembly Steps

Start assembling furniture.

STEP 1

Attach Lock Latch (M) to Cabinet Pull Plate (13) using Screw (C) and the Lock Latch (M) itself.

STEP 2

Attach Drawer Slides (G) to Vertical Plates (1 and 2). Use Screws (C). Note: The pre-drilled holes for locating the drawer slides are relatively small; please look carefully.

STEP 3

Screw Cam Bolts (A) into Vertical Plate (1). Then attach Back Panel (3) to Vertical Plate (1) and secure using Cam Locks (A). Rotate the Cam Locks until they lock.

STEP 4

Attach Vertical Plate (2) to Back Panel (3) and Cabinet Pull Plate (13) using Cam Bolts and Locks (A).

STEP 5

Attach Top Panel (4) to the assembled sides using Cam Bolts and Locks (A).

STEP 6

Attach Caster Gaskets (N) to the Bottom Panel (5) using Screws (C). Attach Pulley Locating Plate (12) to Bottom Panel (5) using Screws (C).

STEP 7

Attach Casters (J) to the Bottom Panel (5). The diagram shows 5 casters being attached.

STEP 8

Attach the Bottom Panel (5) assembly to the main cabinet structure using Screws (F).

STEP 9

Assemble the drawer sides. Attach Drawer Base Plates (10) to Drawer Panels (8, 9, 15, 14) using Screws (C). The diagram shows two drawer assemblies being built.

STEP 10

Connect Drawer Panels (15 and 14) using Cam Bolts and Locks (A).

STEP 11

Attach Drawer Pull Plate (11) to the drawer front panels (15 and 14) using Screws (A).

STEP 12

Attach Drawer Slides (G) to the assembled drawer sides (8, 9, 15, 14) using Screws (F).

STEP 13

Insert the assembled drawers into the cabinet structure. The diagram shows two drawers being inserted, labeled "Upper Drawer" and "Lower Drawer".

STEP 14

Attach Hanging Rods (H) to the drawer sides using Screws (A). Tips: Choose the holes and insert the Hanging Rods before connecting the drawer front panels.

STEP 15

Attach Drawer Front Panel (16) to the drawer body using Screws (E) and attach Handle (D).

STEP 16

Attach Drawer Front Panel (6) to the drawer body using Screws (B) and attach Handle (D).

STEP 17

Attach the Pulley Locating Plate (12) to the Bottom Panel (5) using Wood Dowels (L). The diagram shows the caster assembly being attached to the bottom panel.

STEP 18

Attach Casters (J) to the Pulley Locating Plate (12) using Screws (K).

STEP 19

Insert the drawer (16) into the cabinet. Pull out the sliding part of the drawer slide first, and the balls along with it to the front. Keep the drawer level and insert the drawer with the slides aligned. Note: Failure to level may result in damage to the slides.

STEP 20

Insert the drawer (6) into the cabinet. Pull out the sliding part of the drawer slide first, and the balls along with it to the front. Keep the drawer level and insert the drawer with the slides aligned. Note: Failure to level may result in damage to the slides.

Return & Warranty

Return Policy

VINGLI believes you will absolutely love your file cabinet, but if for some reason you want to return the product, please contact VINGLI customer service directly before you decide to return your product to the retailer. VINGLI's Customer Service organization can answer most concerns and assist you with any questions you may have about your new product.

The item must be returned in good condition, in its original box, with all original proof of purchase, parts, and accessories, within the time frame specified by the retailer it was purchased from.

Warranty

VINGLI warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect. This warranty covers one year from the date of original purchase. This is solely limited to the repair or replacement of defective parts, and no assembly labor is included.

This warranty does not apply to any product which has been improperly assembled, subjected to misuse or abuse, or which has been altered or repaired in any way. Components repaired or replaced are warranted through the remainder of the original warranty period only. The defective components will be repaired or replaced without charge, subject to the terms and conditions described above.

For help with assembly, identifying parts, product information, or to order parts, please contact VINGLI freely.

FAQs

1. What should I do when I received a defective item?

   Please feel free to contact VINGLI customer service via the link where you purchased this item with your order ID and pictures of the defective areas. VINGLI is eager to help you to make it right.

2. Is it easy to put the screws to the panels?

   Yes. As long as you follow the instruction and use the correct screws and put them in the correct holes, it is easy to screw them into pre-drilled holes.

3. What should I do if I have a problem with the drawers not closing flush?

   The problem with the drawers not closing flush is usually caused by the assembly of the drawer slides. Here are the solutions:

   1. Please check whether the slide rail is damaged, for example, if the ball of the slide rail has fallen out. If so, please ask VINGLI for replacements of the drawer slides.
   2. Refer to the assembly manual to check if the holes for the slide rail are assembled correctly. If there is no problem with the assembly, but the slide rail is stuck in the process of pushing in, please release the entire drawer as you did the first time you removed the drawer slides, and then push it back in again.

   Any query, please contact VINGLI directly.

Supplementary Instructions for Safe Use

⚠️ WARNING

(Note: Additional safety warnings are provided in French and German in the original document.)