Philips TAV2000FB Portable Radio

1 Important Safety Information

Safety

Read these instructions. Heed all warnings. Follow all instructions. Do not block any ventilation openings. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Keep this apparatus away from direct sunlight, open flames, or heat. The product shall not be exposed to dripping or splashing. Place the product on a flat, hard, and stable surface. Do not place hazardous objects on the product (such as liquid-filled objects or lit candles). Never place this apparatus on other electrical equipment. Use only accessories specified by the manufacturer. Never remove the casing of this apparatus. Refer all servicing to qualified service personnel. Service is required when the apparatus has been damaged in any way, such as if the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, if it has been exposed to rain or moisture and does not operate normally, or has been dropped. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Danger of explosion if batteries are replaced incorrectly. Replace only with the same or equivalent type. A battery that is used, stored, or transported in extreme high or low temperatures or low air pressure at high altitude may pose a safety risk. Danger of explosion if the battery is replaced with an incorrect type. Replacing a battery with an incorrect type may defeat a safeguard (for example, in the case of certain types of lithium batteries). Insert all batteries correctly. Leaving a battery in an extremely high temperature surrounding or extremely low temperature surrounding may result in a malfunction or leakage of flammable liquid or gas. Batteries contain chemical substances. They should be disposed of properly. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. When replacing batteries, always keep all new and used batteries out of reach of children. Ensure the battery compartment is completely secured after replacement. If the battery compartment cannot be secured completely, stop using the product. Keep out of reach of children and contact the manufacturer. The product shall not be exposed to dripping or splashing. Do not place hazardous objects on the product (such as liquid-filled objects or lit candles). Use the product safely in an environment with temperatures between 0 and 45 °C. To avoid fire hazard, power the equipment only with an external power source that shall conform to PS1 (with capacity lower than 15 W). The power supplied by the charger must be between a minimum of 5 watts and a maximum of 15 watts, which is required to charge the radio equipment at the highest charging speed.

2 Your Portable Radio

Introduction

Congratulations on your purchase and welcome to Philips! Register your product at www.philips.com/support to fully benefit from the support Philips offers. With this portable radio, you can: Listen to FM radio and Bluetooth® music. Set two alarms that ring at different times.

What's in the box

• Main unit
• Type-C charging cable
• Quick start guide
• Safety data sheet
• Warranty

www.philips.com/welcome

Note: Images, illustrations, and drawings shown in this user manual are for reference only, and the actual product may vary in appearance.

Overview of the portable radio

The portable radio has the following controls:

• a Favorite stations (1 or 2): Store presets or direct access to preset 1 or 2.
• b [Snooze/Sleep]: Snooze the alarm. Access sleep settings.
• c [Menu]/[Info]/[Back]: Open settings menu. Display information. Return to previous menu. Exit menu settings.
• d [Volume/Select]/[Scan/Play/Pause]: Adjust the volume or select a menu option. Open list of selectable menu options. Store selected preset stations. Scan and store radio stations automatically. Play/Pause.
• e [Source]: Switch to FM/Bluetooth source. Pair with Bluetooth®.
• f [Power]: Turn on/off or switch to standby mode. Turn off alarm.
• g [Preset Program]/[Select Preset]: Activate preset programming mode. Select a preset radio station.
• h [Navigate/Prev Track]: Set time. Tune to a radio station. Navigate menu. Previous track.
• i [Navigate/Next Track]: Set time. Tune to a radio station. Navigate menu. Next track.
• j Battery compartment cover
• k Headphone jack
• l USB-C Port
• m FM Antenna

3 Getting Started

Always follow the instructions in this chapter in the correct sequence.

Charge the built-in battery

The portable radio is powered by a built-in and rechargeable battery. Note: The [Battery Status] icon is displayed when the battery level is low. Charge the built-in battery as soon as possible. Connect the TYPE-C port on the portable radio to a wall socket (5 V 2 A) using the supplied TYPE-C cable. When the portable radio is charging, the [Battery Status] icon is displayed. When the portable radio is fully charged, the [Battery Status] icon is displayed. Note: Please be aware that your device contains built-in lithium batteries. Lithium batteries' charging capacity decreases over time due to their self-discharge characteristics. To ensure the longevity of the device's battery, we recommend the built-in battery be charged to about 50% every six months when the device is not in use.

Turn on/off or switch to standby mode

• Press [Power] to turn on the unit. The radio switches to the last selected source.
• Press [Power] to activate the unit's standby mode. The time (if set) is displayed. Note: If a Bluetooth device is not connected for 15 minutes or more, or if it is connected but not playing music, the radio automatically activates standby mode. Press and hold [Power] for three seconds, in any mode, to turn off the unit directly. The screen turns off.

Adjust the volume

While listening, you can turn the knob to adjust the volume.

Adjust the display brightness

1. Press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [Display] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Backlight level] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select the screen brightness (High, Medium, Low) and then press [SELECT] to confirm.
5. Press [Back] to close the menu.

Display the menu in standby mode

When the unit's standby mode is active, you can open the menu for control options.

1. Press [Menu] to open the menu with the unit's standby mode active.
2. Turn the knob or press [Navigate/Select] to select a menu option and then press [SELECT] to confirm the option or open a submenu.
   • [Display]: adjust backlight/dimming/timeout settings.
   • [Alarm]: Activate/deactivate alarm 1 or 2 and configure the alarm.
   • [Clock]: Set time synchronization, date/time, and select time and date formats.
   • [System]: Adjust system settings.
3. Repeat step 2 if a submenu is available.
4. Press [Back] to return to the previous menu.

4 Setting the Clock

Note: If no button is pressed for 30 seconds, the menu closes.

Set the clock automatically

1. Press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [Clock] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Set auto/manual] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select [Auto (RDS)] and then press [SELECT] to confirm.
5. Press [Back] to return to the previous menu.

Thanks to FM stations with RDS, the unit can automatically synchronize with the time broadcast by the stations (with CT information).

Set the clock manually

1. Press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [Clock] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Set date&time] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select the hour and then press [SELECT] to confirm. The hour starts blinking.
5. Turn the knob or press [Navigate/Select] to select the minutes and then press [SELECT] to confirm. The minutes start blinking.
6. Turn the knob or press [Navigate/Select] to select the month and then press [SELECT] to confirm.
7. Turn the knob or press [Navigate/Select] to select the day and then press [SELECT] to confirm.
8. Turn the knob or press [Navigate/Select] to select the year and then press [SELECT] to confirm. The time is now set.
9. Press [Back] to return to the previous menu.

Set the time format

1. Press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [Clock] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Set 12H/24H] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select [12H] or [24H] and then press [SELECT] to confirm.
5. Press [Back] to return to the previous menu.

Set the date format

1. Press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [Clock] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Set date format] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select the date format [MM-DD-YYYY], [DD-MM-YYYY], or [YYYY-MM-DD] and then press [SELECT] to confirm.
5. Press [Back] to return to the previous menu.

Clock style

1. Press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [Clock] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Clock style] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select [Classic analog] or [Normal digital] and then press [SELECT] to confirm.
5. Press [Back] to return to the previous menu.

5 Configure the alarm

Set the time for an alarm

Note: Ensure the clock has been set correctly.

1. Press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [Alarm] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Alarm 1 Setup] or [Alarm 2 Setup] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select [Wake Up Time] and then press [SELECT] to confirm. The hour starts blinking.
5. Turn the knob or press [Navigate/Select] to set the hour and then press [SELECT] to confirm. The minutes start blinking.
6. Turn the knob or press [Navigate/Select] to set the minutes and then press [SELECT] to confirm. If [Once] is selected as the alarm period, you can use [Navigate/Select] to set the alarm date.
7. Turn the knob or press [Navigate/Select] to select [Frequency] and then press [SELECT] to confirm. The alarm repeat cycle starts blinking.
8. Turn the knob or press [Navigate/Select] to select the alarm repeat cycle (Once, Daily, Weekdays, or Weekend) and then press [SELECT] to confirm.
9. Turn the knob or press [Navigate/Select] to select [Source] and then press [SELECT] to confirm. The alarm source starts blinking.
10. Turn the knob or press [Navigate/Select] to select the alarm source ([SUMMER] or FM STATION) and then press [SELECT] to confirm. If [FM] is selected as the alarm source (the default is SUMMER), an additional option [Source] will be displayed in the alarm menu. Use [Navigate/Select] to select a preset FM radio station.
11. Press [Back] to return to the previous menu. The corresponding alarm icon [Alarm Active] is displayed.

Tips: The unit exits alarm setting mode after 30 seconds of inactivity. If FM is selected as the alarm source but the preset station is not selected, SUMMER is automatically activated. The alarm duration is 60 minutes if no user action occurs.

Activate/deactivate the alarm timer

1. Press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [Alarm] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Alarm 1] or [Alarm 2] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select [On] or [Off] and then press [SELECT] to confirm to activate or deactivate the alarm time.
5. Press [Back] to return to the previous menu. If the alarm timer is activated, the [Alarm Active] icon is displayed. If the alarm timer is deactivated, the [Alarm Active] icon disappears.

Snooze

1. When the alarm rings, you can press [Snooze/Sleep]. The alarm is snoozed and will ring again after 10 minutes (the default is 10 minutes).
2. While the alarm is snoozed, you can press and hold [Snooze/Sleep] or [Power] for three seconds to cancel the alarm's snooze function. The alarm stops.

Stop the alarm

When the alarm sounds, you can press the [Snooze/Sleep] button to pause the alarm sound and activate snooze mode, or press the [Power] button to stop the alarm sound. The alarm stops, but the alarm settings are retained.

Set the sleep timer

This portable radio can activate standby mode automatically after the sleep time has been set. 1. Turn on the unit. 2. Press [Snooze/Sleep] to select the sleep time. Press and hold [Snooze/Sleep] to select between different sleep times (Off, 15, 30, 45, 60, 90, 120 minutes). You can deactivate the sleep timer by repeating the steps above and setting the sleep timer to Off.

6 Listening to FM radio

Note: Keep the portable radio away from other electronic devices to avoid radio interference. Fully extend the FM antenna and adjust its position for optimal reception.

Automatic scan

1. Press [Power] to turn on the unit.
2. Press [Source] to select FM mode.
3. Press and hold [Scan/Play/Pause] for 3 seconds. The portable radio automatically scans to a station with a strong reception.

Manual scan

Press [Navigate/Prev Track] or [Navigate/Next Track] to manually tune to a station frequency. Note: The portable radio's frequency interval is 50 kHz. The radio frequency on the screen increases by 0.05 MHz when you press [Navigate/Next Track].

Scan and store FM radio stations automatically

Note: You can store a maximum of 20 FM radio stations. Activate FM mode and press and hold [Scan/Play/Pause] for three seconds. [Auto Scanning...] is displayed. The radio automatically scans and stores all FM radio stations and plays the first available station.

Store FM radio stations manually

1. Activate FM mode and tune to an FM radio station.
2. Press and hold [Preset Program] for three seconds to activate programming mode. The preset list is displayed on the screen.
3. Turn the knob or press [Navigate/Select] to select a number.
4. Press [SELECT] to store the station as a preset.
5. Repeat steps 1-4 to save more FM radio stations.

Tips: You can delete an already stored station by storing another one in its place (if the number of preset stations exceeds 20).

Store and select favorite stations

Note: You can store favorite stations on quick buttons 1 and 2. 1. Activate FM mode and tune to an FM radio station. 2. Press and hold [Favorite Station] 1 or 2 (preset number) for three seconds to save the current station to the corresponding position. [Preset 1 or 2 stored] is displayed. The number of the preset station and its frequency are displayed. Activate FM mode and press 1 or 2 to select a preset radio station (1 or 2).

Select a preset radio station

1. Activate FM mode and press [Select Preset].
2. Turn the knob or press [Navigate/Select] to select a preset radio station.

Note: The preset radio station is confirmed automatically after three seconds.

Set the scan sensitivity

1. Press [Menu] to open the FM menu.
2. Press [SELECT] to enter [Scan Setting].
3. Turn the knob or press [Navigate/Select] to select [Strong] (only stations with strong signals) or [All] (all stations) and then press [SELECT] to confirm.
4. Press [Back] to close the menu.

Display RDS information

RDS (Radio Data System) is a service that allows FM stations to display additional information. 1. Tune to an FM RDS station. 2. Press and hold [Info] for three seconds to display the following information (if available): Station name, Program type such as [RDS Info] (news, sport, pop music)..., Time, Text, Frequency.

Open the menu in FM mode

When listening to an FM station, you can open the menu for control options.

1. Press [Menu] to open the FM menu.
2. Turn the knob or press [Navigate/Select] to select a menu option and then press [SELECT] to confirm the option or open a submenu.
   • [Scan Setting]: select scan sensitivity (only stations with strong signals or all stations).
   • [Kitchen Timer]: set the kitchen timer.
   • [Sleep Timer]: set the sleep timer.
   • [Display]: adjust backlight/dimming/timeout settings.
   • [Alarm]: activate/deactivate the alarm and configure the alarm.
   • [Clock]: Set time synchronization, date/time, and select time and date formats.
   • [System]: adjust system settings.
3. Repeat step 2 if a submenu is available.
4. Press [Back] to return to the previous menu.

Note: If no button is pressed for 30 seconds, the menu closes.

7 Listening to music via Bluetooth®

Note: The range between the apparatus and the device is approximately 25 meters (without obstruction between them). Compatibility with all Bluetooth® devices is not guaranteed. Any obstructions between the apparatus and the device may reduce the range. Keep away from other electronic devices that may cause interference. The apparatus will also disconnect when the device is moved out of range.

Connect Bluetooth®

1. Press [Source] to select Bluetooth mode. [Not Connected] is displayed.
2. On the Bluetooth device, turn on Bluetooth, search, and select [Philips TAV2000FB] to start the connection. If the connection is complete: A notification sound is heard. [Connected] is displayed.

Disconnect Bluetooth®

Switch to another source on the unit; Disable the function from your Bluetooth® device. Or press and hold [Source] for three seconds to disconnect the Bluetooth connection. If the connection was disconnected: A notification sound is heard. [Pairing] is displayed. Or 1. Press [Menu] to open the Bluetooth menu. 2. Press [SELECT] to select [Bluetooth Pair]. 3. Turn the knob or press [Navigate/Select] to select [Yes] (disconnect Bluetooth® and activate pairing mode) and then press [SELECT] to confirm.

Clear Bluetooth® pairing information

1. Press [Menu] to open the Bluetooth menu.
2. Turn the knob or press [Navigate/Select] to select [Bluetooth Clean] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Yes] (disconnect current connection) or [No] (keep connection) and then press [SELECT] to confirm.
4. Press [Back] to close the menu. [Pairing] is displayed.

Play music

When music is playing on the Bluetooth® device, this unit can be used to control playback. Press [Scan/Play/Pause] to pause/resume playback. Press [Navigate/Prev Track] or [Navigate/Next Track] to skip to a track. Turn the knob to adjust the volume.

Open the menu in Bluetooth® mode

When listening via Bluetooth®, you can open the menu for control options.

1. Press [Menu] to open the Bluetooth® menu.
2. Turn the knob or press [Navigate/Select] to select a menu option and then press [SELECT] to confirm the option or open a submenu.
   • [Bluetooth Pair]: select to disconnect the Bluetooth connection and activate pairing mode.
   • [Bluetooth Clean]: clear Bluetooth pairing history.
   • [Kitchen Timer]: set the kitchen timer.
   • [Sleep Timer]: set the sleep timer.
   • [Display]: adjust backlight/dimming/timeout settings.
   • [Alarm]: activate/deactivate the alarm and configure the alarm.
   • [Clock]: Set time synchronization, date/time, and select time and date formats.
   • [System]: adjust system settings.
3. Repeat step 2 if a submenu is available.
4. Press [Back] to return to the previous menu.

Note: If no button is pressed for 30 seconds, the menu closes.

8 Configure the kitchen timer

Note: The unit closes the settings menu after 30 seconds of inactivity.

Set the kitchen timer

1. Press [Power] to turn on the unit.
2. Press [Menu] to open the menu.
3. Turn the knob or press [Navigate/Select] to select [Kitchen Timer] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select [Kitchen Timer Setup] and then press [SELECT] to confirm. Or press and hold [Kitchen Timer] to open the kitchen timer. The hour blinks.
5. Turn the knob or press [Navigate/Select] to set the hour and then press [SELECT] to confirm. The minutes blink.
6. Turn the knob or press [Navigate/Select] to set the minutes and then press [SELECT] to confirm. The seconds blink.
7. Turn the knob or press [Navigate/Select] to set the seconds and then press [SELECT] to confirm.
8. Turn the knob or press [Navigate/Select] to select [On/Off] and then press [SELECT] to confirm.
9. Turn the knob or press [Navigate/Select] to select [On] (activate) or [Off] (deactivate) the kitchen timer and then press [SELECT] to confirm.
10. Press [Back] to return to the previous menu. The kitchen timer icon and timer are displayed.

Note: The kitchen timer's time limit is 60 minutes if no user action occurs.

Mute the kitchen timer sound

When the kitchen timer rings, you can press any button to mute the buzzer.

Cancel the kitchen timer

1. To cancel the kitchen timer, you can press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [Kitchen Timer] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [On/Off] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select [Off] and then press [SELECT] to confirm.
5. Press [Back] to close the menu.

Note: The kitchen timer can only be canceled while the unit is powered on.

9 Other functions

Select menu language

1. Press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [System] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Language] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select the menu language and then press [SELECT] to confirm. Available languages include English, Deutsch, Italiano, Français, Norsk, Dansk, Nederlands, Svenska, Español, Suomi, Polski.
5. Press [Back] to return to the previous menu.

Listen with headphones

Connect headphones to the [Headphone Jack] on the back of the main unit.

Factory reset

1. Press [Menu] to open the menu.
2. Turn the knob or press [Navigate/Select] to select [System] and then press [SELECT] to confirm.
3. Turn the knob or press [Navigate/Select] to select [Factory Reset] and then press [SELECT] to confirm.
4. Turn the knob or press [Navigate/Select] to select [Yes] (reset the radio settings to factory defaults) and then press [SELECT] to confirm. [Restarting...] is displayed.

10 Product specifications

Note: Product information is subject to change without prior notice.

Amplifier

• Nominal output power: 5 W RMS (THD 10%)

Tuner

• Tuning range (FM): 87.5–108 MHz
• Tuning step: 50 kHz
• Sensitivity - Mono, 26 dB S/N ratio: < 22 dBf
• Total harmonic distortion: < 10 %
• Signal to noise ratio: > 50 dBA

Bluetooth

• Bluetooth version: V5.4
• Bluetooth frequency band: 2.4–2.48 GHz
• Max. e.i.r.p.: 5.37 dBm
• Bluetooth range: 25 m (without obstruction)

General information

• USB port: 5V 2A
• Lithium battery: 3.65 V/2600 mAh
• Dimensions (W x H x D): 190 x 111.6 x 91.5 mm
• Weight (main unit): 555 g

11 Troubleshooting

Warning: Never remove the product's cover. The warranty becomes void if you attempt to repair the product yourself. If you encounter problems using this unit, check the following points before ordering service. If the problem persists, visit the Philips website (www.philips.com/support). When contacting Philips, ensure the unit is available and the model and serial number are accessible.

No power

• Ensure the portable radio is fully charged.
• Ensure the USB port on the portable radio is connected correctly.

No sound

• Adjust the volume on the portable radio.
• Adjust the volume on the connected device.
• Ensure the Bluetooth device is within range.

No response from the unit

• Restart the portable radio.

Poor radio reception

• Keep the portable radio away from other electronic devices to avoid radio interference.
• Fully extend the antenna and adjust its position.

The alarm does not work

• Set the clock/alarm correctly.

The clock/alarm setting has been erased

• Reset the clock/alarm.
• Replace the backup batteries.

Audio quality is poor after connecting with a Bluetooth-enabled device

• Bluetooth reception is weak. Move the device closer to this speaker or remove any obstructions in the way.

Could not find [Philips TAV2000FB] on the Bluetooth device used for pairing

• Press and hold [Source] for three seconds to activate Bluetooth pairing mode and try again.

Cannot connect to the Bluetooth device

• The Bluetooth function of the device is not enabled. Refer to the user manual for the device on how to enable the function.
• The pairing mode is not active on the portable radio.
• The portable radio is already connected to another Bluetooth-compatible device. Disconnect and try again.

Battery cannot be charged correctly or the battery drains too quickly

• Replace the batteries. 1. Open the battery compartment cover on the back of the unit and remove the original battery from the compartment. 2. Insert a battery of the same type (not supplied). 3. Secure the battery compartment cover. Rechargeable Lithium-ion Battery Specifications: 1INR19/66 Model: TACR5001BA Rated power: 3.65 V, 2600 mAh, 9.49 Wh Max. charging voltage: 4.2 V TP Vision Europe B.V. Prins Bernhardplein200, 1097 JB Amsterdam, The Netherlands.

To purchase an additional battery, visit https://www.philips.com/support for more information.

12 Message

Compliance

Any changes or modifications made to this unit not expressly approved by MMD Hong Kong Holding Limited could void the user's authority to operate the product. TP Vision Europe B.V. hereby declares that this product is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and UK Radio Equipment Regulations SI 2017 No 1206. You can find the Declaration of Conformity on the page www.philips.com/support. This product complies with the radio interference requirements of the European Community. Your product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that the product must not be disposed of as household waste and should be delivered to an appropriate collection facility for recycling. Follow your local rules and never dispose of the product and rechargeable batteries with normal household waste. Proper disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health. This symbol means that the product contains batteries which are covered by EU Regulation (EU) 2023/1542 which cannot be disposed of with normal household waste. Obtain information about your local recycling system for electrical and electronic products and batteries. Follow your local rules and never dispose of the product and batteries with normal household waste. Proper disposal of old products and batteries helps prevent negative consequences for the environment and human health.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.

MMD Hong Kong Holding Limited. All rights reserved. Specifications are subject to change without prior notice. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product.