Heyday TWS10H True Wireless Earbuds

Earbud Tips

The earbuds come with small, medium, and large earbud tips and can be changed at any time. To change the size of the earbud tip, squeeze it and pull it away from the earbud.

To attach a new earbud tip: Select the size that is the most comfortable for you and push it onto the earbud. The earbud tip has an interior sleeve that slides onto the earbud. Repeat for the second earbud.

Charging Earbuds

• Place both earbuds back into the case.
• Charging is complete when lights turn off.
• Full charge requires approximately 2 hours and will provide 6 hours of use.

Charging Case

• Plug the USB-C end of the charger into the back of the case.
• Plug the USB end into a power supply of at least DC 5V 1A.
• Warning: Please use a UL-compliant power supply.
• Full charge requires approximately 2 hours and can play for 20 hours with fully charged earbuds.
• Charging is complete when all 4 LEDs are solid white.

IPX4 Water Resistance

The earbuds are resistant to sweat, which means they're perfect for workouts.

Note: The charging case does not have the same rating and should not be used in the same conditions.

Pairing

Before pairing the earbuds to your device, open the case and remove both earbuds and the padded sticker. Then reinsert the earbuds back into the case to activate them. After that, remove both earbuds from the case, and now they are ready to pair.

The first earbud removed from the case will be the primary earbud. The primary earbud will turn red and white, and the other earbud will flash white when both earbuds have successfully entered pairing mode.

Use the Bluetooth settings on your device to pair with HEYDAY EARBUD 10. When the earbuds have successfully paired, the primary earbud will turn white for 5 seconds and then fade.

Touch Controls

Quick Tip: The touch sensor is located in the center of the earbud; be sure to touch here so inputs register.

Left Earbud

• 1 tap: Play/Pause, Answer/End Call
• Hold 2 sec: Reject Call
• 2 taps: Voice Assist

Right Earbud

• 1 tap: Play/Pause, Answer/End Call
• Hold 2 sec: Reject Call
• 2 taps: Voice Assist

*Indicates that the left and right earbuds have different functions.

Troubleshooting

• If the earbuds aren't working correctly, place them into the case with the lid open and reset them (hold touch sensor on both earbuds for 10 seconds until they turn off and flash red and white 3 times). After resetting, start the pairing process at step 1.
• If the earbuds won't turn on, recharge the battery and try again.
• If the earbuds won't charge, make sure the power supply works, is 5V 1A, not damaged, and that the case is charged.
• If the earbuds still won't charge, make sure the charge pins are clear of debris, as this may cause a connection issue. If they are, use a soft dry cloth to clean them.
• If the earbuds make no sound or do not show as an available device, make sure they are not paired to other devices. If so, unpair the device and repair to the desired device.

Need Some Help?

Can't get it to pair? Have a question or comment?

Call us at: 1-833-TGT-Tech or 1-833-848-8324

Safety

• Do not use near any water source.
• Do not modify or repair this device.
• Do not use chemical detergents to clean your device; use a soft dry cloth.
• Warning: The battery or batteries or battery pack shall not be exposed to excessive heat such as sunshine, fire or the like.

FCC Information

FCC ID: 2A023-TWS10H Model: TWS10H

Input: 5V 1A

Earbud Battery Capacity: 3.7V/40mAh/0.148Wh

Case Battery Capacity: 3.7V/320mAh/1.184Wh

Made in Vietnam

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Manufacturer Information

Target Corp. Mpls. MN, 55403 Phone: 612-304-6073

For qualified repair specialists requesting repair information and parts, please contact the original manufacturer at customersupport@gemsfindyours.com.