Heyday True Wireless Earbuds

Product Overview

Welcome to your Heyday™ true wireless earbuds. This guide will help you get set up.

Included Accessories:

• Charging case
• Wireless earbuds (Left, Right)
• Micro USB charging cable

Dimensions:

• Overall length: 203.2 ±1 mm (8 inches)
• Width: 101.6 ±1 mm (4.0 inches)
• Height: 142 ±1 mm (5.6 inches)

Diagrams:

The product packaging is depicted with three sides labeled: SIDE 1 (BACK), FRONT, and SIDE 2 (P2, P3).

The earbuds and charging case are shown with labels for:

• Charging LED indicator
• LED indicator
• Mic
• Micro USB charging port
• Multifunctional touch control
• Charging point
• Charging pin

Pairing Instructions

1. Remove both earbuds from the charging case to power on. If earbuds are not in the case or are off, press and hold both earbuds for 3 seconds to power on.
2. When the left and right earbuds are connected, the left earbud will flash red and blue, while the right earbud light will turn off.
3. Use your device's Bluetooth settings to pair with "Heyday Earbud 11".
4. The lights on both earbuds will turn off when paired successfully.
5. Place the earbuds back into the charging case to power off.
6. The earbuds will power off automatically after 5 minutes of no connection.

Note: Either the left or right earbud can be used individually. Remove an earbud from the case; it will automatically power on and reconnect to your previously connected device. Alternatively, use your device to pair with "Heyday Earbud 11".

How to Wear

1. Take the earbuds out from the charging case.
2. The left earbud is marked with "L" and the right earbud with "R".
3. Place the left/right earbud into the corresponding ear, ensuring the speakers point upwards.

Using Your Earbuds

Listen To Music

• Play/Pause: Press the touch control on either the Left or Right Earbud once.
• Previous Song: Hold the touch control on the Left Earbud for 2 seconds.
• Next Song: Hold the touch control on the Right Earbud for 2 seconds.

Voice Assistant

• Press the touch control on the Right Earbud 3 times to activate/exit Voice Assistant/Siri.

Phone Calls

• Music will pause for incoming calls.
• Answer/End Call: Press the touch control on either earbud once.
• Reject Call: Press and hold the touch control on either earbud for 2 seconds.

Charging

Charging Earbuds

• Charge the earbuds fully before first use.
• Full charge of the earbuds takes approximately 1 hour.
• Earbud playback time is up to 3.5 hours. Up to 12 hours with the charging case.
• Place the earbuds in the charging case to begin charging. The left and right earbuds will display a steady red light while charging. The lights turn off when fully charged.

Recharging the Charging Case

• Full charge of the charging case takes approximately 1.5 hours.
• Connect the Micro USB charging cable to the charging case.
• The indicating light on the charging case will flash blue while charging the earbuds.
• When the charging case is being charged, the light will flash. It turns steady red when fully charged.

Troubleshooting and Tips

• If the earbuds are not working correctly, try turning them off and on again.
• If the earbuds won't turn on, recharge the battery and try again.
• If the earbuds won't charge, ensure the power supply is working, is rated 5V/0.5A, and is not damaged.
• If there is no sound from the earbuds, adjust the volume on your device.
• If the earbuds make no sound or do not appear as an available device, ensure they are not paired to another device. If they are, unpair the device and re-pair with the desired device.

Notes and Compliance

• This device does not have a pairing code. If prompted, ensure you are connecting to the correct device. If not, "forget" the device and re-pair.
• The unit will power off if not used for more than 5 minutes.
• If the Bluetooth connection range exceeds 10 meters, the earbuds will disconnect with an audible prompt. If the connection is not re-established within 5 minutes, the earbuds will turn off automatically.
• Safety Precautions:
• Do not use near any water source.
• Do not modify or repair this device.
• Do not use in high temperatures or extreme weather.
• Do not use chemical detergents to clean your device; use a soft, dry cloth.
• FCC Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
• The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
• If this equipment causes harmful interference to radio or television reception, users are encouraged to try to correct the interference by:
• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment to an outlet on a different circuit than the receiver.
• Consulting the dealer or an experienced radio/TV technician for help.