Reese Twin Roomsaver Bed Assembly Instructions
Model Numbers: SP -1707, 273543, 273547
Brand: Living Spaces
Part List
| # | Part Name | Quantity |
|---|---|---|
| 1 | Book Case | x1 |
| 2 | Right Hip Bed | x1 |
| 3 | Left Hip Bed | x1 |
| 4 | Rail | x3 |
| 5 | Slat (13pcs) | x1 |
| 6 | Drawer | x1 |
Diagram Description: An isometric illustration of the Reese Twin Roomsaver Bed. It shows a headboard with integrated shelving (Book Case), the main bed frame structure with side rails, and two drawers located beneath the bed platform.
Hardware
| # | Hardware Name | Quantity |
|---|---|---|
| A | Bolt 05/16"x70mm"(D13) | x12 |
| B | Bolt 05/16"*15*11 | x12 |
| C | Wooden Pegs#10x40mm | x10 |
| D | Bolt 05/16"x50mm"(D13) | x4 |
| E | Screw #4x25mm | x6 |
| F | Screw #4x30mm | x26 |
| G | Allen Key | x1 |
Anti-Tip Kit Hardware
| # | Hardware Name | Quantity |
|---|---|---|
| H | Metal Plate | x4 |
| I | Screw #4x15mm | x2 |
| J | Screw #4x50 mm | x2 |
| K | Restraint Strap | x2 |
Diagram Description: An exploded view of all bed components and hardware. The bed frame parts (headboard, side rails, drawer unit) are shown separated, along with all the different types of bolts, screws, pegs, and the allen key, each labeled with its corresponding letter or number.
Assembly Steps
Step 1: Prepare Components
Identify all parts and hardware from the lists above.
Step 2: Attach Side Rails to Headboard/Footboard
Connect the Left Hip Bed (#3) and Right Hip Bed (#2) to the headboard section (part of #1). Use Bolts (? #A), Wooden Pegs (? #C), and the Allen Key (? #G) to secure these connections. Ensure the pegs are inserted into their corresponding holes before tightening the bolts.
Diagram Description: This page shows two main assembly stages. Stage 2 focuses on attaching the side rails (#2, #3) to the headboard section. Close-up insets detail how Bolts (#A), Wooden Pegs (#C), and the Allen Key (#G) are used to connect these pieces. The Rail (#4) is shown being positioned.
Step 3: Assemble the Bed Frame Base
Attach the Rails (#4) to the assembled side panels. Use Bolts (? #A), Wooden Pegs (? #C), and the Allen Key (? #G) for securing. The diagram shows the drawer unit (#6) being slid into place between the side panels.
Diagram Description: Stage 3 shows the drawer unit (#6) being slid into the partially assembled frame. The connection points for the side panels and rails are highlighted, indicating the use of hardware like Bolts (#A), Pegs (#C), and the Allen Key (#G).
Step 4: Secure Drawer Unit
Slide the Drawer Unit (#6) into the main bed frame. Secure it using Screws (? #E) through the pre-drilled holes on the side panels into the drawer unit.
Diagram Description: Step 4 illustrates the Drawer Unit (#6) being secured to the side panels. Close-up views show Screws (#E) being driven through the side panels into the drawer unit.
Step 5: Install Slats
Place the Slats (#5) across the bed frame. Secure each slat using Screws (? #F) into the designated spots on the side rails.
Diagram Description: Step 5 depicts the Slats (#5) being placed onto the bed frame. Close-up views show Screws (#F) used to attach the slats to the side rails.
Step 6: Attach Bookcase/Headboard
Attach the Book Case (#1) to the main bed structure. Use Bolts (? #D), Wooden Pegs (? #C), and the Allen Key (? #G) to secure it to the side panels and potentially the footboard section.
Diagram Description: Step 6 shows the Book Case (#1) being attached to the top of the assembled bed frame. Insets detail the use of Bolts (#D), Wooden Pegs (#C), and the Allen Key (#G) for this connection.
Step 7: Final Check
The bed is now assembled. The drawers can be pulled out.
Diagram Description: Step 7 presents a view of the fully assembled Reese Twin Roomsaver Bed, with the drawers extended.
Step 8: Insert Drawers
Slide the assembled drawers into their respective slots within the bed frame.
Diagram Description: Step 8 shows the drawers being inserted into the bed frame. Arrows indicate the sliding motion.
Step 9: Install Anti-Tip Kit
For safety, it is recommended to secure the bed to the wall using the provided Anti-Tip Kit. Attach Metal Plates (? #H) to the back of the bed frame using Screws (? #I). Attach the Restraint Strap (? #K) to the metal plate. Secure the other end of the strap to the wall using Screw (? #J) into a wall stud or appropriate wall anchor.
Diagram Description: Step 9 details the installation of the Anti-Tip Kit. It shows the bed against a wall, with Metal Plates (#H) attached to the bed, a Restraint Strap (#K) connecting the bed to the wall, and Screws (#I, #J) used for securing. The word "WALL" is explicitly labeled.
