Summit Twin Bookcase Daybed w/ 4 Drawer Storage Unit

Hardware and Tools

Assembly Time: 1 Person, 45 Minutes

Hardware Included:

Tools Required:

• 4mm Allen Wrench (Included)
• 4mm Allen Drill Bit (Ensure the bit is fully seated into the bolt head before turning)
• Phillips Screwdriver

Recommendation: Using a power driver with the drill bits is recommended.

Important Note: Ensure lag bolts are started into the frame rail holes during assembly. Do not fully tighten until the assembly is loosely complete.

Product Description and Parts

The Summit Twin Bookcase Daybed is a stylish and functional piece of furniture featuring four drawers for storage and a bookcase headboard.

Visual Description: The product is shown in two images: one from the front, displaying the daybed with its drawers closed and bookcase headboard; the second from an angled front view, with some drawers open to reveal storage space.

Parts List:

• A) 8 - 100mm Decorative Head Lag Bolts
• B) 1 - Roomsaver Headboard (This headboard is compatible with both Twin and Full bed sizes)
• C) 2 - End Assemblies with doors. The doors are designed to open outward, allowing you to determine the Right or Left side placement.
• D) 2 - 3 1/4" x 75" Mattress Rails with Support Cleats
• E) 3 - 3 1/2" x 38 3/4" Loose Slats for a Twin bed, or 3 - 3 1/2" x 53 3/4" Loose Slats for a Full bed
• F) 10 - 1 1/4" Wood Screws
• G) 2 - 2" x 4" Mending Plates
• H) 2 - ½" x 2" Straight Brackets
• I) 16 - #8 x 1" Screws
• J) 2 - 2 1/4" L-brackets
• K) 8 - #8 x 3/4" Screws

Assembly Instructions

Ensure all parts are present before beginning assembly. For missing parts, contact the dealer where the bed was purchased.

1. Attach two mattress rails (E) to headboard/footboard assemblies (D) using 8 lag bolts and 8 washers, then tighten.
2. Spread the slat roll across the bed frame from end to end. Secure the slat roll with wood screws in the four outside corners, ensuring the slats are pushed tightly against the bed end. Insert three loose slats into the gaps within the slat roll and screw them down. Refer to subsequent pages for detailed slat installation information.
3. Refer to the next page for headboard installation and L-bracket installation for the underdresser.

Headboard Bracket Placement

Follow these steps for attaching the headboard brackets and connecting the underdresser components.

5. Attach one ½" x 2" straight bracket at each end of the headboard. These brackets should span the joint between the top rail of the end assemblies (D) and the bottom edge of the headboard uprights.
6. Attach a 2x4 bracket inside each end, centered on the headboard ends.
7. Attach two 2 ¼" 'L' brackets to the top of the underdresser corner blocks at each end. Also, attach them to the back of the front side rail cleat as shown in Detail C. Use two additional 2 ¼" brackets to connect the back, bottom ends of the underdresser to the bottom rail of each end panel, as depicted in Detail D.

Detail C Description: Shows a 2 1/4" 'L' bracket positioned on the top corner block of the underdresser and attached to the front side rail cleat.

Detail D Description: Shows a 2 1/4" 'L' bracket connecting the bottom back end of the underdresser to the bottom rail of the end panel.

Slat Installation

Instructions for installing slats, whether using a slat roll or individual slats.

When using a slat roll, position the three individual slats evenly within the gaps and beneath the strapping before securing them.

For use with Bunkie Board (sold separately): Consult your retailer for Bunkie Board purchases.

For use with Slat Roll (sold separately): Consult your retailer for Slat Roll purchases.

Diagram Description (Individual Slats with Bunkie Board): Illustrates the placement of screws for installing individual slats when using a Bunkie Board.

Diagram Description (Individual Slats with Slat Roll): Illustrates the placement of screws for installing individual slats when using a Slat Roll.