DALSKÄR Wash-basin Mixer Tap

About This Product

This document provides installation instructions for the IKEA DALSKÄR wash-basin mixer tap.

Important Safety Information:

ℹ️ Installation must be carried out in accordance with Industry Regulations Säker Vatteninstallation.

⚠️ Switch off the main shut-off valve before changing the mixer tap.

Certifications: TG 1179, KIWA 1913, EN 817 | EN 1717

RSK Number: 8430089

Technical Specifications

Recommended Operating Temperature: Max. 60°C

Maximum Operating Temperature: Max. 80°C

Recommended Operating Pressure: 1-5 bar

Maximum Operating Pressure: 0.5-10 bar

Water Connection: G 3/8" (R10)

Required Hole Diameter: Ø 34 - 37 mm (Ø 1 3/8" - 1 7/16")

Maximum Worktop Thickness: 50 mm (2")

Tools and Spare Parts

Tools Required (not included):

• Adjustable wrench
• Coin (for aerator)
• Silicone sealant (water- and mould-resistant, EN 15651-3, Class XS1)
• Possibly a sealant gun

Included Parts:

• Mixer tap body with handle and spout
• Mounting bracket/plate (1x)
• Mounting screws/bolts (2x)
• Flexible hoses (2x)
• Hex key/Allen wrench (1x)
• Aerator/Flow guide
• Drain assembly components (stopper, body, seal, rod, etc.)
• Various washers and nuts

Part Numbers Reference:

• 10044928
• 10046279
• 110084
• 121844
• 121845
• 121846
• 124405
• 124607
• 126907
• 190555
• 190556
• 10095582
• 10097281

Assembly Instructions

Step 1: Mount the Mixer Tap

Insert the mixer tap body through the hole in the sink or countertop. From underneath, secure the tap using the provided mounting bracket and screws. Ensure the tap is correctly oriented.

Step 2: Connect Water Supply

Connect the flexible hoses to the water supply inlets on the mixer tap. Ensure a secure connection.

Step 3: Seal the Base

Apply silicone sealant around the open surfaces where the tap meets the countertop to prevent water ingress. The silicone is not included. Use a water- and mould-resistant silicone sealant suitable for installation, conforming to EN 15651-3, Class XS1.

Step 4: Connect to Water Mains

Connect the flexible hoses to the hot and cold water supply pipes. The pipe connection must be flat and free from sharp edges. IMPORTANT: Do not overtighten connections, as this can damage hoses, pipes, and washers. Ensure correct hose connections are used; avoid incorrect types (indicated by crossed-out diagrams).

Step 5: Prepare for Use

Before initial use, unscrew the aerator/flow guide with a coin. Allow water to run freely for a few minutes to flush out any debris. Screw the aerator/flow guide back into place until it stops. DO NOT OVER TIGHTEN.

Step 6: Check for Leaks

Periodically check the installation to ensure there are no leaks.

Step 7: Install the Pop-Up Drain

The mixer tap includes a pop-up drain mechanism. Follow these steps:

7a. Install Drain Body: Insert the drain body into the sink's drain hole from the top. From underneath the sink, secure the drain body with the provided rubber seal and retaining nut. Ensure the overflow connection point is oriented correctly.

7b. Install Stopper Mechanism: Insert the stopper assembly into the drain body from above. Connect the pop-up rod to the stopper mechanism.

7c. Connect Pop-Up Lever: Attach the pop-up lever to the back of the mixer tap body. Connect the pop-up rod from the stopper to the lever mechanism.

7d. Test Operation: Operate the pop-up lever to ensure the drain stopper opens and closes smoothly.