Contents
- Tools and spare parts
- Illustration of product, parts and part numbers
- Product assembly
Important Information & Safety
ℹ️ Note: Installation shall be carried out in accordance with Industry Regulations Säker Vatteninstallation.
⚠️ Warning: Switch off main shut-off valve before changing mixer tap.
Certifications: EN 200 | EN 1717, KIWA. RSK No: 8258000.
Preparation
Gather necessary tools: [Screwdriver], [Wrench], [Sealant gun] (2 units required).
Visit www.IKEA.com for more information.
If you encounter difficulties during assembly, consult the IKEA website or visit an IKEA store for assistance.
Parts List
| Item | Description | Part Number | Quantity |
|---|---|---|---|
| 1 | Flexible hose | 10128645 | 2x |
| 2 | Flexible hose | 10128652 | 2x |
| 3 | Mixer body with spout and handles | 10128642 | 1x |
| 4 | Mounting bracket/nut | 10128648 | 1x |
| 5 | Aerator/Flow guide | 10046279 | 1x |
| 6 | Fixing screw | 10044928 | 1x |
| 7 | Washer/Seal | 124405 | 2x |
| 8 | Nut | 121844 | 2x |
| 9 | Fixing plate | 121845 | 1x |
| 10 | Mounting screw | 121846 | 1x |
| 11 | Sealant ring | 126907 | 1x |
Assembly Steps
1
Information:
Recommended Operating temperature: Max. 60°C
Maximum Operating temperature: Max. 80°C
Recommended Operating Pressure: 1-5 bar
Maximum Operating Pressure: 0,5-10 bar
Connect the flexible hoses ([Part 1, 2]) to the mixer tap body ([Part 3]).
2
Secure the hose connection by tightening the nut ([Part 8]).
3
⚠️ Important: Seal the open surfaces with silicone sealant (not included) to prevent water from penetrating the worktop upon any leaks. Silicone sealant must be water- and mould-resistant and suitable for the installation, according to EN 15651-3, Class XS1.
Apply silicone sealant around the tap base. Ensure the mounting hole diameter is between 34 - 37 mm (1 3/8" - 1 7/16"). Sealant should be applied up to 50 mm (2") from the edge.
4
Tighten the mounting nut ([Part 4]) securely using two [Wrench] tools.
5
ℹ️ Note: The pipe connection needs to be flat and free from sharp edges.
⚠️ Important: Do not tighten too hard: this can damage hoses/pipes and washers.
Ensure correct connection of hoses, avoiding sharp edges. Do not overtighten.
6
ℹ️ Before use: Unscrew the Aerator/Flow Guide ([Part 5]) and allow the water to run freely for a few minutes. Then screw the Aerator/Flow Guide back in place. Ensure that it is tight to prevent removal by hand.
ℹ️ Maintenance: Check at regular intervals to make sure that the installation is not leaking.
Sink Drain Assembly
The following steps illustrate the assembly of a sink drain, often installed with the mixer tap.
Step 1
Insert the drain body (part 10128642) into the sink's drain hole.
Step 2
Insert the stopper mechanism (part 10044928) into the drain body.
Step 3
From underneath the sink, secure the drain body using a fixing plate (part 10097281) and a fixing screw (part 10044928).
Step 4
Attach the overflow cover (part 10097281) and the stopper.
Step 5
Attach the mounting plate (part 10046279) and mounting nut (part 10044928) from underneath the sink and tighten.
Step 6
Connect the overflow pipe (if applicable).
Step 7
Attach the final stopper cover (part 10128648).
Step 8
ℹ️ Note: Clean the drain regularly.
