HAMNSKÄR Wash-Basin Mixer Tap
IKEA of Sweden
Product Overview
This document provides assembly and installation instructions for the IKEA HAMNSKÄR wash-basin mixer tap.
General Installation Guidelines
Installation: Must be performed in compliance with current local construction and plumbing regulations. If in doubt, contact a professional.
Before Use: Unscrew the Aerator/Flow Guide and allow the water to run freely for a few minutes. Then screw the Aerator/Flow Guide back in place. Ensure that it is tight to prevent removal by hand.
Maintenance: Check at regular intervals to make sure that the installation is not leaking.
IMPORTANT! Do not tighten too hard: this can damage hoses/pipes and washers.
Tools and Requirements
- ? Two wrenches (2x)
- Required hole diameter: 34 - 37 mm (1 3/8" - 1 7/16")
- Water connection: G1/2"
- Operating pressure: 0.5 - 10 bar (7.2 - 145 psi)
- Maximum temperature: 60°C (140°F)
- Maximum temperature (hot water): 80°C (176°F)
Refer to www.IKEA.com.
Parts List
The following parts are included:
- Part 10044928: Handle base component (1x)
- Part 10046279: Handle cap component (1x)
- Part 121845: Mounting bracket/plate (1x)
- Part 121846: Mounting bracket/plate (1x)
- Part 121844: Mounting bracket/plate (1x)
- Part 10093113: Long threaded rods (2x)
- Part 126907: Installation tool (1x)
- Part 10095595: Cartridge
- Part 10092255: Cap
- Part 10004087: Aerator/Flow Guide
- Part 10091769: Swivel spout
Parts for Drain Assembly:
- Part 10124733: Screw (1x)
- Part 10128770: Washer (1x)
- Part 10124732: Screw (1x)
- Part 10128771: Washer (1x)
- Part 10124748: Drain cover (1x)
- Part 10128669: Seal (1x)
- Part 10124727: Drain body (1x)
- Part 10128667: Seal (1x)
- Part 10124734: Drain pipe connector (1x)
- Part 10128671: Seal (1x)
Assembly and Installation Steps
Step 1: Prepare the Tap
Insert the long threaded rods (Part 10093113) through the base of the tap body. Ensure they are properly seated.
Illustration showing the tap body with two long threaded rods being inserted from below. Step 2: Mount the Tap
Place the tap assembly through the mounting hole in the sink or countertop. From underneath, attach the mounting plates (Parts 121845, 121846, 121844) and secure them with the nuts on the threaded rods. Use the provided installation tool (Part 126907) to tighten.
Illustration showing the tap being placed into a sink hole from above, and from below, the threaded rods being secured with mounting plates and nuts using a special tool. Step 3: Connect Water Hoses
Connect the flexible water supply hoses (not explicitly listed as parts but implied) to the threaded rods. Tighten them securely using wrenches, but do not over-tighten.
IMPORTANT! Do not tighten too hard: this can damage hoses/pipes and washers.
Illustration showing flexible water hoses being connected to the threaded rods under the sink, with a close-up showing the correct connection method and a crossed-out illustration of an incorrect or damaged connection. Step 4: Flush and Install Aerator/Flow Guide
Before initial use, unscrew the Aerator/Flow Guide (Part 10004087). Allow water to run freely for a few minutes to flush out any debris. Then, screw the Aerator/Flow Guide back into place and ensure it is tight enough to prevent removal by hand.
Illustration showing the aerator/flow guide being screwed into the tap spout. Step 5: Check for Leaks
After installation, check at regular intervals to ensure the installation is not leaking.
Illustration indicating a check for water leaks.
Drain Assembly Installation
The following steps detail the installation of a compatible drain assembly.
Step 1: Insert Drain Body
Place the drain body (Part 10124727) into the sink drain hole from above. Ensure the seal (Part 10128667) is correctly positioned.
Illustration showing the drain body being inserted into the sink drain hole from above. Step 2: Secure Drain Body
From underneath the sink, attach the mounting nut and washer (e.g., Parts 10124733/10128770 or 10124732/10128771) to the drain body. Tighten securely.
Illustration showing the drain body being secured from underneath with a nut and washer. Step 3: Attach Drain Cover and Pipe Connector
Attach the drain cover (Part 10124748) and seal (Part 10128669) to the top of the drain body. Connect the drain pipe connector (Part 10124734) to the bottom of the drain body, ensuring the seal (Part 10128671) is in place. Tighten.
Illustration showing the drain cover being placed on top and the pipe connector being attached to the bottom of the drain assembly. Step 4: Install Stopper Mechanism
Insert the stopper mechanism (Part 10044928) into the drain assembly. The mechanism allows for opening and closing the drain.
Illustration showing the stopper mechanism being inserted into the drain assembly. Step 5: Final Check and Disposal
Ensure all connections are secure. Dispose of any packaging materials properly.
Illustration showing the assembled drain with a basket for waste, and a curved arrow indicating disposal.
Hej! Welcome to IKEA Global
