Salto XS4 One Installation Guide

Product Overview and Specifications

The Salto XS4 One offers advanced access control with a modern design.

Dimensions and Components

Outside Handle Dimensions: Height: 160mm, Width: 42mm

Inside Handle Dimensions: Height: 125mm, Width: 42mm

Handle Projection: 19.5mm

Spindle Height: 106mm

Escutcheon Height: 145mm

Hardware Included

• TORX 20 screws (x2)
• TORX 20 screw (x1)
• TORX 20 screws (x6)
• ALLEN 3 screws (x2)
• BOLT (quantity depends on door thickness)

Compatible Model Series

• E i 750xx series
• E i 751xx
• E i 752xx
• E i 753xx
• E i 754xx
• E i 756xx
• E i 757xx
• E i 7P0xx
• E i 7P1xx
• E i 7P6xx

Standards Compliance

EN16867: 2020 + A2: 2024 (Classification: 4 7 B 2 4 D 0 0)

⚠️ Note: This device is intended for use with the 7F model. (Model 112)

Diagram Description: A diagram showing the dimensions of the outside and inside handles, the spindle, and the escutcheon. A list of compatible electronic lock series and required hardware is also presented. A warning symbol ⚠️ with "112- FOR 7F MODEL" is shown.

Compatibility and Recommendations

Latch Compatibility

Must be used with SALTO Tubular latch only.

Escutcheon Compatibility

To be used only with SALTO compatible escutcheons.

Mortise Lock Recommendation

SALTO recommends the use of a mortise lock with a maximum 4° pre-turn. This ensures optimal performance and alignment.

Important Note on Model 7F

For models 56-57 and P6 with distance 7F, the self-drilling screw cannot be used to improve escutcheon vertical alignment.

Diagram Description: Shows a SALTO tubular latch and its compatibility with SALTO compatible escutcheons. A mortise lock is shown with a maximum 4° pre-turn. A note about the 7F model and self-drilling screw is included. Symbols: Ø (diameter), [thickness > 60mm].

Installation Steps

Step 1: Select Handing

Determine whether the door requires a left-hand or right-hand lock mechanism. The diagrams show how to orient the handles accordingly.

Diagram Description: Shows the two handle halves and how they connect, with arrows indicating the selection of the correct handing (left or right).

Step 2: Prepare Door

Drill necessary holes in the door. This typically involves Ø14mm holes for mounting screws and a MIN.Ø25mm hole for the spindle or mechanism.

Diagram Description: Illustrates drilling holes of Ø14mm and MIN.Ø25mm into the door. Then shows mounting the electronic unit.

Step 3: Install Tubular Latch and Escutcheon

Install the SALTO tubular latch and the compatible escutcheon onto the door.

Diagram Description: Shows a SALTO tubular latch and its compatibility with SALTO compatible escutcheons. A mortise lock is shown with a maximum 4° pre-turn. A note about the 7F model and self-drilling screw is included.

Step 4: Mount Electronic Unit

Attach the main electronic unit to the door mechanism.

Diagram Description: Shows mounting the electronic unit onto the door mechanism.

Step 5: Connect Wires

Carefully connect the electronic wires from the handle to the main unit. Ensure proper connection.

Diagram Description: Shows connecting the electronic wires from the handle to the main unit.

Step 6: Check Alignment

Verify that all components are correctly aligned. The diagram indicates "NOT OK" scenarios to avoid.

Diagram Description: Shows checking component alignment, with a "NOT OK" indication and a warning symbol ⚠️.

Step 7: Install Batteries

Insert LR03 AAA batteries into the electronic unit. Ensure correct polarity.

Diagram Description: Shows inserting LR03 AAA batteries into the electronic unit.

Step 8: Attach Handles

Secure the handles using the provided TORX 20 screws and ALLEN 3 screws. Ensure all screws are tightened appropriately.

Diagram Description: Illustrates the assembly of the handle mechanism, showing the insertion of parts and securing with TORX 20 screws. Labels 'L' and 'R' for left/right handing. Shows tightening a component with a 3mm Allen screw.

Step 9: Final Assembly and Programming Warning

Complete the handle attachment. ⚠️ IMPORTANT: AT THIS POINT DO NOT CLOSE THE DOOR. PROGRAM THE LOCK FIRST. Failure to program before closing the door may require re-installation.

Diagram Description: Shows final handle attachment. A prominent warning symbol ⚠️ with text "AT THIS POINT DO NOT CLOSE THE DOOR. PROGRAM THE LOCK FIRST."

Model Variations and Features

Entry Lock with Privacy/Lockout Function

Models such as E i 756 xx and E i 7P6 xx offer enhanced security features including privacy and lockout functions, and a key override option.

• Privacy Mode: Activate by pressing the [push privacy] button.
• Key Override: Use the [European Cylinder Override] for emergency access.

Diagram Description: Shows different models (E i 756 xx, E i 7P6 xx) and their features like privacy/lockout function and key override. Shows how to activate privacy mode with "PUSH PRIVACY" and "European Cylinder Override" options.