Resistex Miks Downlight Installation Guide

Product Features

This fixture is available in versions with 'Orientable/Adjustable' capabilities, allowing the light direction to be changed. It also comes in 'Basse Luminance/Low Light' configurations.

Orientable/Adjustable Feature:

• Step 1: Shows a fixture component with a ring.
• Step 2: Illustrates the ring being inserted into the main fixture body.
• Step 3: Depicts the ring being rotated to lock it into place.

Basse Luminance/Low Light Feature:

• Step 1: Shows the fixture body.
• Step 2: Illustrates spring clips being attached to the fixture.
• Step 3: Shows the fixture with attached springs being pushed into a ceiling opening.

Safety Notes

Never work when voltage is present on the luminaire.

The installation must be performed by a professional installer in compliance with the standards and regulations relating to electrical installations.

⚠️ Risk of electrostatic discharges (ESD Norm). Handle with precautions.

Please observe the notes and steps described in the mounting instructions.

Maintenance Instructions

Do not use chemicals or abrasives products to clean the fixture.

Keep these instructions for dismantling or future maintenance. Additional information about RESISTEX luminaires is available on the website www.resistex-sa.com.

RESISTEX cannot be responsible for any misuse of the product.

Installation Steps

Step 1: Prepare the Ceiling Cutout

Cut a hole in the ceiling with a diameter of Ø69 mm (+/-1 mm).

Diagram Description: Shows a circular cutout in a ceiling panel with dimensions indicated.

Step 2: Insert the Fixture

Carefully insert the Resistex Miks downlight into the prepared ceiling cutout.

Diagram Description: Shows the downlight fixture being pushed upwards into the ceiling hole.

Step 3: Secure the Fixture

Rotate the fixture to engage its mounting clips or springs, securing it firmly in place.

Diagram Description: Shows the fixture being rotated within the ceiling opening, with arrows indicating the direction of rotation for securing.

Step 4: Prepare Electrical Connection

Open the push-in connector on the fixture's wiring.

Diagram Description: Shows a close-up of an electrical connector, with a mechanism to open it for wire insertion.

Step 5: Connect Wires

Insert the electrical wires (Line, Neutral, and Earth) into the corresponding terminals of the push-in connector. Ensure correct polarity.

Diagram Description: Shows wires being inserted into the open terminals of the push-in connector. A diagram within this step indicates the terminal layout: 'L' for Line, 'N' for Neutral, and a connection for Earth.

Step 6: Finalize Connection and Position

Close the push-in connector to secure the wires. Gently push the fixture fully into the ceiling, ensuring the mounting springs are engaged.

Diagram Description: Shows the connector being closed, and the fixture being pushed into the ceiling, with springs holding it.

Step 7: Verify Installation

Ensure the connection is correct. A proper connection is indicated by a stable electrical signal (✔️), while an incorrect connection may show a sharp spike or interruption (❌).

Diagram Description: Two graphs are shown. The top graph (with a checkmark ✔️) depicts a stable electrical signal. The bottom graph (with a cross ❌) depicts an unstable or interrupted signal.

Step 8: Final Appearance

The Resistex Miks downlight is now correctly installed and flush with the ceiling.

Diagram Description: Shows the completed installation with the downlight fitted neatly into the ceiling.

Product Information & Certifications

Website: www.resistex-sa.com

Company: RESISTEX EXPLOITATION

Address: 11 Quai de la Banquière CS 80010, 06730 Saint-André-de-la-Roche - France

Contact: Tél. 04 93 276 276 - Fax 04 93 276 280 - contact@resistex-sa.com

Company Registration: APE 2740Z - Siret 487 593 477 00010 - SAS CAPITAL 649979 € - T.V.A. F.R. 73 487 593 477

Certifications: ROHS, Classe II, IP65, IK07, IK82, CE.