Hooke Road
MAKE A DIFFERENCE
Front Fender Flares
Model: BXG.3054
(1) Contents:
Diagram showing the driver side and passenger side front fender flares.
| Qty | Part Name | Size(mm) | Picture Description |
|---|---|---|---|
| 2 | Button Head Socket Cap Bolts Screws | M8*20 | Image of an M8*20 Button Head Socket Cap Bolt Screw. |
| 8 | Button Head Socket Cap Bolts Screws | M6*20 | Image of an M6*20 Button Head Socket Cap Bolt Screw. |
| 8 | Split Lock Washer | D6 | Image of a D6 Split Lock Washer. |
| 2 | Flat Washer | M8*16*1 | Image of an M8*16*1 Flat Washer. |
| 8 | Flat Washer | M6*16*1 | Image of an M6*16*1 Flat Washer. |
| 6 | Flange Hex Lock Nuts | M6 | Image of an M6 Flange Hex Lock Nut. |
| 2 | Flange Hex Lock Nuts | M8 | Image of an M8 Flange Hex Lock Nut. |
| 2 | Rivet Nut | M6 | Image of an M6 Rivet Nut. |
| 2 | Rubber Strip | 25000 | Image of a Rubber Strip. |
(2) Tools required:
- Drive Socket Ratchet Wrench
- 4mm & 5mm Hex Bit Socket
- Rivet Nut Tool (Package Included)
- 10mm & 13mm Wrench
Image of the included Hand Rivet Nut Tool and a sample bolt.
(3) Installation time:
Approximately 1 hour. 2-3 people may be needed. Installation time may differ according to mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
To view the electronic version (BXG.3054), please scan the QR code.
(4) Installation instruction:
Driver Side Front Fender Flare Installation:
Step 1: Remove the factory front fender flare. Prepare for product installation.
Step 2: Before installation, apply rubber strips along the edges of the fender to prevent scratching the car surface.
Diagram illustrating the application of rubber strips along the fender's edge.
Step 3: Install the rivet nut in the most right hole with the rivet nut tool. Follow these instructions for the rivet nut tool: Use the 4mm Hex Bit Socket on the top, and the 10mm wrench on the middle nut. Insert the rivet nut into the hole, screw the threaded end of the rivet nut tool into the rivet nut (Notice: Must be screwed to the bottom), then unscrew the rivet nut tool.
Images demonstrating the installation of a rivet nut using the rivet nut tool, showing the 4mm hex bit socket and 10mm wrench in use.
Step 4: Lift up the front fender flare and install the left two holes. Use the M8*20 Button Head Socket Cap Bolts Screws and M6*20 Button Head Socket Cap Bolts Screws. Do not tighten these bolts yet.
Images showing the installation of Button Head Socket Cap Bolts Screws into the fender flare.
Step 5: Install the middle two holes. Use the M6*20 Button Head Socket Cap Bolts Screws. Do not tighten these bolts yet.
Images showing the installation of Button Head Socket Cap Bolts Screws into the fender flare.
Step 6: Finally, for the rightmost hole, use the extended rod tool to screw in the screw, and then cover the plug back.
Images demonstrating the installation of a screw using an extended rod tool and covering it with a plug.
Step 7: After completing the driver side installation, follow the same installation method on the passenger side.
Lighting Wiring Installation:
The fender flare lights have the function of a Turn lamp.
Installation: Locate the factory fender flares light wiring harness. Connect the wiring harness as follows:
- Negative Electrode (Black Wire) connects to Factory Black Wire.
- Turn Lamp (Red Wire) connects to Factory White Yellow Wire.
Notes: Different models may have different wiring harness colors, but the above wiring methods are the same.
Diagram of the fender flare light, indicating its function as a turn lamp and the wiring connection point.
Images showing the vehicle's wiring harness and the connection points for the fender flare lights: Black wire to Black wire, Red wire to White Yellow wire.
Step 8:
The installation is complete. Hooke Road hopes you enjoy a wonderful off-road life with this quality product!
Image of a Jeep Wrangler equipped with the installed Hooke Road Front Fender Flares.
Attention:
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
