Hooke Road
MAKE A DIFFERENCE
Fender Flares BXG.3049
Contents
This document outlines the installation process for the Hooke Road BXG.3049 Fender Flares.
- Front Fender Flares
- Rear Fender Flares
- Connecting Brackets (A, B, C)
Parts List
Front Components
| Qty | Part Name | Size(mm) |
|---|---|---|
| 6 | Button Head Socket Cap Bolt | M8*20 |
| 12 | Button Head Socket Cap Bolt | M6*20 |
| 12 | Split Lock Washer | D6 |
| 6 | Flat Washer | M8*16*1 |
| 12 | Flat Washer | M6*16*1 |
| 10 | Flange Hex Lock Nut | M6 |
| 6 | Flange Hex Lock Nut | M8 |
| 2 | Rivet Nut | M6 |
Rear Components
| Qty | Part Name | Size(mm) |
|---|---|---|
| 12 | Button Head Socket Cap Bolt | M6*35 |
| 12 | Split Lock Washer | D6 |
| 12 | Flat Washer | M6*16*1 |
| 4 | Flange Hex Lock Nut | M6 |
| 8 | Rivet Nut | M6 |
Tools Required
The following tools are necessary for installation:
- Drive Socket Ratchet Wrench
- 4mm & 5mm Hex Bit Socket
- Rivet Nut Tool
- 10mm & 13mm Wrench
Note: Hand Rivet Nut Tool (Package Included) ?️
Installation Time
Approximately 1.5 hours. 2-3 people may be needed. Installation time may vary based on mechanical skill level.
Important: Please verify all parts are present and read instructions carefully before starting installation.
To view the electronic version (BXG.3049), please scan the QR code (QR code omitted).
Installation Instructions
Driver Side Front Fender Flare Installation:
Step 1: Remove the factory front fender flare. Prepare for product installation.
Step 2: Install the rivet nut in the rightmost hole using the rivet nut tool. Instructions for the rivet nut tool: Use the 4mm Hex Bit Socket on the top and the 10mm wrench on the middle nut. Insert the rivet nut into the hole. Screw the threaded end of the rivet nut tool into the rivet nut until it is fully seated (Notice: Ensure it is screwed fully to the bottom). Finally, unscrew and remove the rivet nut tool.
Notes: The accompanying image demonstrates the use of the rivet nut tool.
Step 3: Lift the front fender flare and align it with the three upper mounting holes. Install using Button Head Socket Cap Bolts (M8*20), Flat Washers (M8*16*1), and Flange Hex Lock Nuts (M8). Do not fully tighten these bolts yet.
Step 4: Install the connecting brackets (A, B, and C) in the correct order. Ensure you distinguish between driver and passenger side brackets. Use Button Head Socket Cap Bolts (M6*20), Flat Washers (M6*16*1), and Flange Hex Lock Nuts (M6). Tighten the bolts from this step and Step 3.
Diagram illustrating the different front connecting bracket types (A, B, C) for driver and passenger sides.
Driver Side Rear Fender Flare Installation:
Step 5: Remove the factory rear fender flare. Prepare for product installation.
Step 6: Install rivet nuts into the four designated holes using the rivet nut tool.
Step 7: Install the rear fender flare. Use Button Head Socket Cap Bolts (M6*35), Split Lock Washers (D6), and Flat Washers (M6*16*1). The upper mounting holes require Flange Hex Lock Nuts (M6). Tighten all bolts for this step.
Step 8: Repeat the installation steps for the passenger side.
Completion:
Step 9: Installation is complete. Enjoy your off-road adventures with your new Hooke Road fender flares!
Important Notes:
1. Product parts may vary slightly from illustrations, but this generally does not affect installation.
2. For any questions regarding your purchase, please contact your distributor.
