Hooke Road Front Bumper BXG.8805
ATTENTION: Please verify all parts are present and read instructions carefully before starting installation. Please feel free to contact your distributor if you have any kind of question about your purchase.
Contents
Parts List:
- A1&A2&A3: Bull Bar
- D1&D2: License Plate Brackets
- B: Main Body
- C1&C2: Wings
- E: Winch Power Control Box Bracket
| Qty | Part Name | Size(mm) | Picture | Qty | Part Name | Size(mm) | Picture |
|---|---|---|---|---|---|---|---|
| 6 | Hex Bolt | M12×35 | [Image of M12x35 Hex Bolt] | 6 | Flat Washer | M8 | [Image of M8 Flat Washer] |
| 6 | Hex Bolt | M12×30 | [Image of M12x30 Hex Bolt] | 4 | Flat Washer | M6×12×1 | [Image of M6x12x1 Flat Washer] |
| 6 | Hex Bolt | M8×20 | [Image of M8x20 Hex Bolt] | 2 | Nylon Round Spacer | M6×12×1.3 | [Image of M6x12x1.3 Nylon Round Spacer] |
| 4 | Hex Bolt Plate | M6×16 | [Image of M6x16 Hex Bolt Plate] | 12 | Hex Nut | M12 | [Image of M12 Hex Nut] |
| 8 | Hex Bolt | M4×20 | [Image of M4x20 Hex Bolt] | 6 | Flange Hex Lock Nut | M8 | [Image of M8 Flange Hex Lock Nut] |
| 12 | Button Bolt | D12 | [Image of D12 Button Bolt] | 4 | Nylon Lock Nut | M6 | [Image of M6 Nylon Lock Nut] |
| 6 | Split Lock Washer | D8 | [Image of D8 Split Lock Washer] | 1 | L-Wrench | M4 | [Image of M4 L-Wrench] |
| 18 | Split Lock Washer | M12×30×1.5 | [Image of M12x30x1.5 Split Lock Washer] | 2 | EVA | [Image of EVA material] |
Tools Required
- Drive Ratchet Handle
- 10mm, 13mm Wrench
- 4mm Hex Bit Socket
- 19mm Wrench
To view online instruction, please scan the QR code. [QR Code]
Installation Instruction
Step 1
Place the vehicle in park, remove the factory bumper from the frame.
[Image of vehicle with factory bumper removed]
Step 2
First, stick the EVA to the main body. Assemble your Hooke Road bumper. Align the outer profile with the inner profile and tighten the hardware. Repeat this step on the other side of the bumper.
- (6) M12×30 Hex Bolts
- (6) D12 Split Lock Washers
- (6) M12×30×1.5 Flat Washers
- (6) M12 Hex Nuts
- (2) EVA
[Diagram showing EVA attachment to the main body and initial assembly]
Step 3
Assemble the license plate bracket, then secure it to the bumper and tighten the hardware.
- (4) M6×16 Buttom Bolts
- (4) M6×12×1 Flat Washers
- (2) M6×12×1.3 Nylon Round Spacers
- (4) M6 Nylon Lock Nuts
[Diagram showing license plate bracket assembly and attachment]
Step 4
Secure the bull bar to the bumper and tighten the hardware.
- (4) M8×20 Hex Bolts
- (4) D8 Split Lock Washers
- (4) M8 Flat Washers
- (4) M8 Flange Hex Lock Nuts
[Diagram showing bull bar attachment to the bumper]
Step 5
Secure the winch power control box bracket to the bumper and tighten the hardware.
- (2) M8×20 Hex Bolts
- (2) D8 Split Lock Washers
- (2) M8 Flat Washers
- (2) M8 Flange Hex Lock Nuts
[Diagram showing winch power control box bracket attachment]
Step 6
Secure the bumper to the vehicle frame. Adjust the bumper to the desired position. Finally, tighten all bolts.
- (6) M12×35 Hex Bolts
- (6) D12 Split Lock Washers
- (12) M12×30×1.5 Flat Washers
- (6) M12 Hex Nuts
[Diagram showing final bumper attachment to the vehicle frame]
Step 7
The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!
[Image of the fully installed front bumper on the vehicle]
